Tender For Repair/Maintenance/Rescanning And Polishing Of Wooden And Misc Furniture And Fixing Ply Charpoy And Bed Hard Under Ge (I) Kanpur; 1 Chair Dining FD-1105/279(a)Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Rear leg 2 (ii) Front leg 3 (iii) Rear/front/side rail 4 (iv) Stiffener 5 (v)Back rest 6 (vi) S&F recanningin Godrej pattern with 2mm wide & 0.6mm thick for centre portion and 4mm wide plastic cane for borders including dismantling unserviceable one complete all as specified and directed. 7 (vii) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng complete all as specified and shown on drg and as directed by EIC. 8 Chair Easy FD-1108/229(a)Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Rear leg 9 (ii) Front leg 10 (iii) Arms 11 (iv) Front/back/Side rail of seat as to match with the existing, made of shisham wood complete all as specified and directed. 12 (v) S&F recanning seat & backin Godrej pattern with 2mm wide & 0.6mm thick for centre portion and 4mm wide plastic cane for bordersincluding dismantling unserviceable one complete all as specified and directed. 13 (vi) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 14 Chair writing FD-202/ 250/280S&F new components of 2nd class HW (shisham) including dismantling unservicable one complete all as specified and directed.(a) Rear leg 15 (b) Front leg 16 (c)Rear/front/Side rail 17 (d)Arms. 18 (e) Back rest 19 (f) Stiffener 20 (g) S&F recanningseat & back of the chairand recanning in Godrej pattern with 2mm wide & 0.6mm thick for centre portion and 4mm wide plastic cane for bordersincluding dismantling unserviceable one complete all as specified and directed. 21 (h) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 22 Bed plywood top FD-245 & 246S&F new componentscomprising of following outer member made of shisham wood and internal frame made of cheer wood, covered both sides ofboard with 3.5 mm thick OST plywoodwith 12mm thick half cut teak wood beading including dismantling unservicable one complete all as specified and directed.(a) Head board 23 (b) Foot board 24 (c) S&F new teak plywoodof head board on both sidesalong with 30mm x 6mm teakwood beading on top including dismantling unserviceable one complete all as specified and directed. 25 (d) S&F new teak plywoodof foot board on both sides along with 30mm x 6mm teakwood beading on top including dismantling unserviceable one complete all as specified and directed. 26 (e)S&F new components of 2nd class HW (shisham) including dismantling unservicable one complete all as specified and directed.(a) Long rail of size 90 x 35 mm 27 (f) Stiffner of size 60 x 40 mm 28 (g) Wooden bracket (corner) 29 (h) S&F top made of 12mm BWR phenol bonded commercial plywood with suitable screwsincluding dismantling unservicable one complete all as specified and directed. 30 (j) preparation of the surfaces by throughly rubbing with emery paperboth surfaces of the head board, foot board including legs and long rails and polishing with french polish two coats to obtain a glossy finish complete all as specified and directed. 31 Table dining for 08 personsFD-30(M)/ 273 & 239 (a) Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Leg 32 (ii) Top rail (long/front) 33 (iii) Top rail (short/side) 34 (iv) Top 18mm thick prelaminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) with 0.8 mm thick PVC edging and laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 35 (v) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 36 Table dining for 06 personsFD-30(M)/ 273 & 239 (a) Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Leg 37 (ii) Top rail (long/front) 38 (iii) Top rail (short/side) 39 (iv) Top 18mm thick prelaminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) with 0.8 mm thick PVC edging and laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 40 (v) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 41 TeapoyFD-382/ 232 & 278Top 18mm thick prelaminated HDHMR board BSD (Make-Century ply/Green ply/Archid ply/Action tesa) with 0.8 mm thick PVC edging and colour/shade as approved by Engineer-in-Chief.(a) Leg 42 (b) Top rail (long/front) 43 (c) Top rail (short/side) 44 (d) Stiffener 45 (e) Top 18mm thick prelaminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) with 0.8 mm thick PVC edging and laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 46 (f) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 47 Table centreFD-274 & 235(a) Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Leg 48 (ii) Top rail (long/front) 49 (iii) Top rail (short/side) 50 (iv) Stiffener 51 (v) Top 18mm thick prelaminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) with 0.8 mm thick PVC edging and laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 52 (vi) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 53 Table PegFD- 277 & 236/384(a)Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Leg 54 (ii) Top rail (long/front) 55 (iii) Top rail (short/side) 56 (iv) Stiffener 57 (v) Top 18mm thick prelaminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) with 0.8 mm thick PVC edging and laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 58 (vi) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 59 Table writingFD-249 & 275(a)Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) S&F new components of 2nd class HW (shisham) including dismantling unservicable one complete all as specified and directed. 60 (ii) Leg (long) 61 (iii) Leg (short) 62 (iv) Side/bottom rail 63 (v) Backmade out of 6 mm thick plywood commercial including dismantling unserviceable one complete all as specified and directed. 64 (vi) Sidemade out of 18 mm thick Pre-laminated MDF board one side laminated finish including dismantling unserviceable oneall as specified and as 65 (vii) Stiffner (long) 66 (viii) Top made out of 18mm thick prelaminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) with 0.8 mm thick PVC edging and laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg including provision of knob including dismantling unserviceable one complete all as specified and directed.Note :-Knob shall be be aluminium anodised (Dark Brown) chromium plated of approved size and quality 67 (ix) Complete cupboard including drawer from the table writing and made of 18 mm thick pre-laminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) including back provided with 6mm thick commercial plywood including dismantling unserviceable one complete all as specified and directed.Note :- (a)Knob shall be aluminium anodized (dark brown chromium plated of approved size & quality).(b) Hinges shall be 50 mm of approved quality. 68 (x) Preparation of surfaces with sand/emery paper and applying french polish two coats of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with beas wax complete all as specified and directed. 69 Hat Stand (FD-361/362) (a) S&F 4mm thick teak face Plyto make front side along with teak wood edging of size 35mm x6 mm including dismantling of old unserviceable one complete all as specified, directed and shown on drawings. 70 (b) S&F of Back commercial plywood including dismantling unserviceable one complete all as specified, directed and shown on drawings. 71 (c) S&F of brass Pegs of size 75mm(W) x 120mm (H) including dismantling of old unserviceable one complete all as specified, directed and shown on drawings. 72 (d) S&F of 5mm looking mirror with edging including dismantling of old unserviceable one complete all as specified, directed and shown on drawings. 73 (e) M&L for preparation of surfaces with sand / emery paper and applying french polish one or more coats of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with bees wax complete along with two key plates all as specified and directed. 74 Removing of glass of Hat Stand and S&F New 6mm Glass god quality (Make- Modguard) as applicable as per drg and as per direction by EIC. 75 Side boardFD-372(a) S&F door shutters (both) made of 18mm thick Pre-laminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) boardduly providing 6mm thick teak wood beading all round with fittings and fixtures including dismantling unserviceable one complete all as specified and directed.Note :- (i) Knob shall be aluminium anodized (dark brown chromium plated of approved size & quality).(ii) Hinges shall be 50 mm of approved quality. 76 (b) Front portion of the drawer as to match with the existing made out of 18mm thick Pre-laminatedMDF board andknob including dismantling unserviceable one complete all as specified and directed. 77 (c) New top made out of 18mm thick Pre-laminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa)duly providing 4mm thick teak wood beading all round including dismantling unserviceable one complete all as specified and directed. 78 (d)S/F 4mm thick one side teak face plywood on sidesincluding dismantling unserviceable one complete all as specified and directed. 79 (e) Backmade out of6mm thick commercial ply wood including dismantling unserviceable one complete all as specified and directed. 80 (f) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 81 Table 900 x 600 mm with/ withoutdrawer FD- 223 & 224(a)Removal of following existing unserviceable wooden components of various MES F/DB/FD/MAP/TP/SPL furniture items or similar items carefully without distrubing the adjoining parts and S&F new components in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, wedging, glueing, providing hinges, placing everypart in-tact the disturbed portion, as applicable as per drgs and as directed by EIC.(b) Work will be executed where the furniture exist in different under units of GE (I) Kanpur Cantt including BSOs Furniture Yard as directed by EIC.(c) Timber Shall be 2nd class teak wood seasoned. CRCA section/CRCA sheet shall be used in repair/maint of steel furniture.(i) Leg 82 (ii) Top rail (long/front) 83 (iii) Top rail (short/side) 84 (iv) Top made ofpre-laminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 85 (v) Drawer made of 12mm thick commercial plywood and front side made of 18mm thick pre-laminated MDF board including provision of knob completed all as specified and directed. 86 (vi) Preparation of surfaces with sand/emery paper and applying french polish one or more coat of approved quality to achieve uniform smooth texture and high glossy finish after filing holes with beas wax complete all as specified and directed. 87 Table 900 x 900 mm Wdn (FD-88)S&F new components of 2nd class HW (shisham) including dismantling unservicable one complete all as specified and directed.(a) Leg 88 (b) front/Side rail 89 (c) Top made ofpre-laminated HDHMR board BSL (Make: Century Ply/Green/Archid Ply/Action Tesa) exterior grade 18mm thick post-formed with 0.6 mm thick laminated in Mohigni/Walnut colour/shade as approved by Engr-in-Charge with 2 mm thick PVC edging of Make : Rehau/Pegasus/Kynes shall be fixed on two sides it complete with strong bonded chemical adhesive through hot pressed machine all as specified in drg and as directed by Engr-in-Charge. 90 (d) M&L for melamine polish with spray machine after removing of existing polish by scapping and smothening of surface wherever required or as directed by EIC to the following furniture articles all are of MES pattern viz F/DB/FD/MAP/spl type series or similar items incl applying wac for depressed surface as well as washing with caustic soda wherever required before polishng all as specified and shown on drg and as directed by EIC. 91 Charpoy GI pipe (FD-220)S&F following components of Charpoy GI pipe including dismantling unservicable one all as specified and directed.(a) Long rail made of 32 mm dia GI Tubing medium grade ISI mark 1.88 mtr long, threaded at both ends and fixing to 3 way 32 mm dia GI elbow of charpoy. 92 (b) 3 way 32 mm dia GI elbow ISI marked 93 (c) Check nuts of 32 mm dia 94 Conversion of 32 mm dia long rail obtained from item No 1 above into two numbers short rail after cutting and threading both ends and fixing to 3 way 32 mm dia existing elbow including dismantling existing one. 95 Conversion of 32 mm dia short rail obtained from item No 4 above into two numbers leg including fixing to 3 way 32 mm dia after one end threaded . 96 Removing old unserviceable/rustedMS Plate and S&F new MS Plate of size900mmx40mm x 5mm duly painted with black colour after applying red oxide after making two Nos holes. 97 (a) M&Lfor removing old U/S plywood and S&F New12 mm BWR phenol bonded commercial plywood of size 2020 mm x 900 mm including fixing of plywood with new 12NosNut and bolts (75mmx6). 2mm teak wood eading complete reast all as per ply with applying with red colour. Necessary reassembling the components as where required to fixing components and tighten the charpoy frame to make original shape of charpoy as per drg before fixing the ply top. Rest all as per directed by Engr-in-Charge. 98 (b) M&L for painting two coat of synthetic enamel paint with silver shade of Charpoy LegS&Frame as approved by EIC/GE. 99 Charpoy with hard top (FD/MAP/04)M&Lfor removing old U/S plywood and S&F New12 mm BWR phenol bonded commercial plywood of size 1980 mm x 900 mm including fixing of plywood with new 12NosNut and bolts (75mmx6).Necessary reassembling the components as where required to fixing components and tighten the charpoy frame to make original shape of charpoy as per drg before fixing the ply top. Rest all as per directed by Engr-in-Charge. 100 S&F following components of Charpoy with hard top including dismantling unservicable one all as specified and directed.(a) Stiffenersmade of 25x25x16 mm Gauge MS Tube, tighten the charpoy with hard top frame to make original shape of charpoy as per drg. Rest all as per directed by Engr-in-Charge. (Make : Jindal/Bansal/Tata) 101 Removing old unserviceable/rustedLegs and S&F new MS plate 32x32x5 welded at Bottom of legs & over which 3 mm Thk Rubber sheet fixed with adhesive. the charpoy with hard top frame to make original shape of charpoy as per drg. Rest all as per directed by Engr-in-Charge. 102 Removing old unserviceable/rustedMS Plate and S&F new MS Plate of size900mmx40mm x 5mm duly painted with black colour after applying red oxide after making two Nos holes.
