Tender For Construction Of Toilet And Rest Room Infront Of Ncb-Ii In Vocpa.; 1 Earthwork excavation in trenches for foundation in sand and other loose soils not exceeding 1.50m in width and including dressing of sides and ramming of bottom lift upto 1.50m including getting out of the excavated soil and disposal of surplus excavated soil as directed within a lead of50m and lift of 1.50m, cost including shuttering, strutting, bailing out seepage of water wherever necessary etc., complete complying with AISS and as directed by the departmentalofficers.Laying and Jointing PVC Pipe. Heading 2 Providing and laying Plain Cement Concrete 1:4:8 (One part of cement, 4 parts of Coarse sand & 8 Parts of 40 mm nominal size metal ) for foundation using 40 mm nominal size graded metal including mixing, laying, levelling, consolidation, finishing and curing etc., complete complying with AISS and as directed by the departmental officers.Brick work in C.M 1:5 mix including all labour charges etc complete 3 Providing Form work including centring, shuttering, (shuttering Planks shall not less than 38 mm thick) so as to give a rough finish shuttering and propping etc., in all floors upto full height of the building and removal of the same for in situ RCC work such as beam, slabs, lintels, sunshade etc., complete complying with AISS and as directed by the departmental officers.Construction of chamber for 100mm sluice plates 4 Providing and laying Reinforced Cement Concrete 1:1.5:3 (One part of cement, One and a half parts of Coarse sand & Three Parts of graded stone aggregate (i.e.) 2 parts of 20mm nominal size graded metal & 1 part of 10mm nominal size graded metal) using 20 mm nominal size graded metal including mixing, laying, levelling, consolidation, finishing and curing etc., and excluding the cost of form work and reinforcement grills for all RCC works in all floors upto full height of the building etc., complete complying with AISS and as directed by the departmental officers.Construction of chamber for 100mm sluice plates 5 Fabricating and placing in position of M.S / Tor steel grills for R.C.C works in all floors including cost of Steel, cutting, bending, binding with 16 Gauge GI Binding wire and placing in position etc., complete complying with AISS and as directed by the departmental officers.Construction of chamber for 100mm sluices valve 6 Brick work in Cement Mortar 1:5 (M. Sand (Crushed Stone Sand)) ( One cement, five M. Sand (Crushed Stone Sand)) using chamber burnt bricks for walls in Ground Floor of the building including cost of all materials, labour, curing etc., complete complying with AISS and as directed by the departmental officers.Laying and Jointing PVC Pipe. Heading 7 Providing Half Brick Masonry wall using chamber burnt bricks in Cement Mortar 1:3 (M. Sand (Crushed Stone Sand)) (One cement, three M. Sand (Crushed Stone Sand)) for partition walls etc., in Ground level including cost of all materials, labour, scaffolding, etc., complete complying with AISS and as directed by the departmental officers. 8 Plastering the Brick work 15 mm thick in Cement Mortar 1:5 (Plastering Sand (P-Sand)) (One cement, five Plastering Sand (P-Sand)) for all faces of walls (even and uneven) in all floors upto full height of the building including necessary scaffolding, racking of masonry joints, cleaning, curing etc., complete complying with AISS and as directed by the departmental officers.Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost 9 Lime Surki Mortar 1:2 for Weathering course 10 Finishing the top of weathering course with one course of machine pressed tiles of size 23 cm X 23 cm X 2cm in Cement Mortar 1:3 (M. Sand (Crushed Stone Sand)) including all materials, labour, etc., complete complying with AISS and as directed by the departmental officers.The Total value of Schedule4 11 Supplying and fixing UPVC WINDOWS (Un-Plasticized Polyvinyl Chloride) windows of casement type (open) from the profile the size of outer frame 60mmX58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with overall the edges of frame and shutter. The shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storm sand should have key lockable action, security protective hinges, strong locking system sand as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with100% packing with screw sand silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work. The rate including cost of all materials, labour, tools & plants, conveyance, fixing in position etc., complete and as directed by the departmental officers. 12 Supplying and fixing in position of best Indian make chinaware water closet of indian style (white color) of approved quality (make parryware/Hindware) and size 580mmx440mm with foot rests (Oriya type) with necessary P or S trap in brick jelly concrete in lime mortar 1:2 (one lime two sand) and plastering with CM 1:3 (one cement, three sand) finshing roughly to receive floor finish including all materials, labour etc., complete complying with AISS and as directed by departmental officers. 13 Supplying and fixing UPVC ( Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm X 58mm and shutter profile size of 60 X 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work. The rate including cost of all materials, labour, tools & plants, conveyance, fixing in position etc., complete and as directed by the departmental officers. 14 Supplying and fixing of Lipped Mouth Porcelin Flat Urinal (White) of approved quality with all accessories such as 32mm dia bell mouth PVC connection, 15mm dia G.M wheel valve, 15mm ida B class GI waste water pipe, 15mm dia nylon coneection, 15mm dia brass nipple, including all materials, labour etc., complete complying with AISS and as directed by lthe departmental officers. 15 Providing and fixing of Anodized Aluminium Door of various size (manufactured to relevant IS Specification) of 37.5 x 37.5mm Vertical and Door bottom rails using 67.5 x 37.5mm including providing 5.5 mm thick glass superior quality for top panel and with Novapan of 8 mm thick at bottom panel with necessary accessories like snap on beading (clips), cleat angles, fully threaded 75mm long metal screws, wooden plugs & metal screws etc., wherever required, all as directed at site of work including all materials, labour, tools, equipments, scaffolding, transport, fuel, etc., complete. Note: Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including using glazing clip, rubber beading for glazing and necessary screws, plugs etc., complete and as directed by the departmental officers. 16 Supplying and fixing of Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer with Double Speed Adjustment like HARDWYN (make) GAZEL (or) Equivalent (with ISI Monogram) for the doors including cost of door closer, accessories, labour, tools, etc., complete and as directed by thedepartmental officers 17 Supplying and fixing Solid Panel PVC door with frame - Supplying and fixing Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter etc., complete and as directed by the departmental officers. 18 Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary labour and furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work. 19 Providing and laying approved colour and quality of Stain Free Nano Polish Vitrified Tiles 600 x 600 x 8mm in Cement Mortar 1:4 (M. Sand (Crushed Stone Sand)), 20 mm thick. The rate inclusive of cost of tiles, all materials, labour, white cement, conveyance etc., complete complying with AISS and as directed by the departmental officers. 20 Supply of Ewc Tank (flush TANK) at Maintenance sub division office including conveyance charges complete and as directed by the departmental officers. 21 Supplying and fixing in position of Brass Chromium Plated Shower Rose -100mm dia. including all materials, labour etc., complete complying with AISS and as directed by the departmental officers. 22 Supplying and fixing in position of 600 x 450 mm size Mirror of best make, first quality approved by the department including plywood back, plugs, screws etc., complete complying with AISS and as directed by the departmental officers. 23 Supplying and fixing in position Brass Chromium Plated Soap Tray of size 150mm x 100mm first quality approved by the department including plugs, screws, all materials, labour etc., complete complying with AISS and as directed by the departmental officers. 24 Supplying and fixing in position of Brass Chromium Plated Towel Rail60cm long and 20mm dia. with Brackets first quality approved by the department including plugs, screws, all materials, labour etc., complete complying with AISS and as directed by the departmental officers. 25 Supplying and fixing in position Stainless Steel Health Faucet first quality approved by the department including plugs, screws, all materials, labour etc., complete complying with AISS and as directed by the departmental officers. 26 Supplying and fixing of 1000 litres capacity Sintex double layer water tank with approved brand including cost of PVC water tank, making connection with input and output water pipe line and valves. Cost inclusive of all materials, labour charges, & conveyance etc., complete and as directed by the departmental officers. 27 Providing and fixing Precoated metal sheet 0.45mm for Roofing with hot dipped galvanised prepainted steel sheet for roof of make TATA or equivalent including cost of metal sheet, conveyance, fixing the sheet with necessary clamps / screws and labour charges for fixing sheet etc., complete complying with AISS and as directed by the departmental officers. 28 Supplying and fixing in position of chinnaware Wash Basin (White color) 550 mm x 400mm size with pedestal of approved quality with necessary fittings such as cast iron bracket, 1 no 15mm C.P heavy duty piller tap with pentagonal head, 32mm dia PVC waste water pipe and 15mm dia nylon connection, 1 No 15 mm dia G.M. wheel valve and fixing it with the wall with necessary plugs, clamps and screws, and giving water supply connection and painting the exposed pipe connection with two coats of paint of approved colour, including all labour, materials etc., complete complying with AISS and as directed by the departmental officers. 29 Supplying and fixing in position of best Indian make heavy duty Gun Metal Wheel Valve at 32mm dia. of approved quality including all materials, labour etc., complete complying with AISS and as directed by the departmental officers. 30 Supplying and fixing 25mm dia. PVC pipe 10 kg. per cm2 working pressure in wall, ceiling and floor with necessary clamps and screws, making holes in the wall wherever necessary by drilling holes in the roofs and walls, packed the holes with necessary brick works or concrete wherever necessary plastering the surface smooth with required scaffolding including cost of pipe and special such as elbows, tee, union joints, reducer etc., cutting threading etc., complete complying with AISS and as directed by the departmental officers. 31 Supplying and fixing 32mm dia. PVC pipe 10 kg. per cm2 working pressure in wall, ceiling and floor with necessary clamps and screws, making holes in the wall wherever necessary by drilling holes in the roofs and walls, packed the holes with necessary brick works or concrete wherever necessary plastering the surface smooth with required scaffolding including cost of pipe and special such as elbows, tee, union joints, reducer etc., cutting threading etc., complete complying with AISS and as directed by the departmental officers. 32 Supplying and laying in trenches 110 mm dia. PVC inflow pipe line 6 Kg./CM2 with necessary pipe specials such as elbow, tee, union joint etc., and the joints being tightened including threading cost of pipe, specials etc., complete complying with AISS and as directed by the departmental officers. 33 Supplying and fixing in position 15mm dia. Heavy type Brass Chromium Plated Pillar tap of approved quality including all materials, labour etc., complete complying with AISS and as directed by the departmental officers. 34 Painting TWO coats with Plastic emulsion paint of approved brand and colour over New Wallsurfaces including one coat of alkalin resistance primer of approved brand so as to give aneven shade.Prior to applying the primer, the wall surfaces shall be thoroughly cleaned of allgrease, dirt, loose pieces, scales and make the surface even by applying wall putty and make good of the surface with sand paper etc., The cost including preparing the surface, all materials, labour, brushes, scaffolding, etc., complete complying with AISS and as directed by the departmental officers. 35 Applying One coat of Alkali Resistant Primer and Two coats of APEX - Exterior Emulsion Paint of approved colour and quality over the New wall surface in all floors to give an even shade after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand paperes smooth including all materials, labour, brushes, scaffolding, etc., complete complying with AISS and as directed by the departmental officers. 36 Supplying, fabricating and fixing in position of Steel Truss of span 3m, Top, bottom and vertical member with 50 x 50 x 6mm M.S. Angle with joint plates of 16mm thick to connect with the existing column, necessary foundation bolts & nuts of required length. The rate including cost of 50 x 50 x 6mm M.S. Angle, M.S. Plates, welding rod, hire charges for welding machine, transportation charges from fabrication yard to work site, handling charges in both end for hosting, erection to the required height, fixing charges, including one coat primer and two coats of synthetic enamel paint, labour, tools, equipments, etc., complete and as directed by the departmental officers. 37 Providing and fixing granite slabs (jet black) of 20mm thick (super fine polished with nosing edges) on the steps area of building, in between urinals and wherever required. The rate inclusive of cost of granite slab, chemical component, white cement, labour charges & conveyance etc., complete and as directed by the departmental officers. 38 Writing letters or figure on any surface with enamel painting (stops, comas, hyphens and the like not to be measured and paid for seperately) of approved colour and quality for 15 CM height letters including cost of enamel paint, labours, scaffolding charges and cleaning the surface etc., complete complying with AISS and as idrectred by the departmental officers. 39 Supplying, fabricating and fixing in position of GI pipe ladder for a height of 6m using 40mm dia. GI pipe as vertical member & joint horizontal step using 40mm dia. GI pipe and for Hand Rail of required lengt using 20mm dia GI pipe. The rate including cost of 40mm dia. GI pipe, 20mm dia. GI pipe, transportation charges, fabrication charges, fixing charges, including one coat primer and two coats of synthetic enamel paint, labour, tools, equipments, etc., complete and as directed by the departmental officers.
