Tender For Spl Repair And Refurbishment To Toilet T 02 Repairs To Joinery Blinds Allied Works At Kalinga Block At Dssc Wellington.; 1 Demolition of floor hearth or wall tilinglaid bedded and pointed in any mortar (but not backing) complete all as specified and directed. 2 Demolition of cement concrete (unreinforced ) of any description and in any postion not otherwise spcifically provided etc (below or above ground level)as in roof pad /floors etc and removing debris off the site complete all as specified and as directed. 3 Dismantling MS steel work of any descrption as in fencing post,MS line wire ,Gate etc complete all as specified and as directed 4 Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed. 5 Taking down chowkats or frames including shutters (without taking off shutters from the frames)exceeding 1.50 Sqm and not exceeding 4 Sqm eachcomplete all as specified and directed. 6 Refixingpartiton of any pattern or any sizewith frame at the opening where directed inlcuding repalace/repair of any acessories as required etc including making good the surface complete all as direted. 7 M&L forfactory made UPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality figured glass /5mm thick UPVC board with EPDM Rubber gasket (as required)complete all as direted. (Note: The unit rate quoted by contractor shall be deemed to include the cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) 8 Material and labour for UPVC door with shutters .The construction profile shall be overall frame sectional size 60x 58mm with wall thickness 2.70+/- 0.2mm extruded sections.The corners shall be plastic welded.The hinge side vertical outer frame shall be reiforced with galvanised steel profileof wall using 8mm dia 80mm long MS screws minimum 3 Nos on each side.The glazing shall be fixed to door frame with UPVC standared beading s of sectional size 24.05x16mm & 2mm thick.The bottom portion of door shutter shall be provided with UPVC board 5mm thick & 1Mtr in height andthe balance shall be glazed excluding the shutter frame area.The shutter shall be fixed to frame using 3Nos of 3D hinges.The door shutter shall beprovided with 6 mm thick toughened glass & 5mm UPVC board with EPDM rubber gasket, zinc plated mild steel multipoint locking arrangementwith key incl zinc alloy (white powder coated) handles andtwo numbers zinc alloy (white powder coated) tower bolts complete all as specified and as directed.The cost of glass, sheet etc shall be deemed to be included with the quoted rate. 9 Supply and fixing factory made UPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality,incl Glazing shall be provided with 4.8mm thick Plain / frosted glass in square not exc 0.5 Sqm in each pane fixed with appropriate size beading as per manufacurers specificationsandStainless steel wire mesh 0.36mm nominal dia and average width of aperature 1.40mm shall be provided with each window shutter, complete all as specified and directed.Note: For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. ® PER SQUARE METRE S & F Material only. 10 S&Ffor UPVC Fixed ventilators with glazing made up of (small series) frame 47x50mm, mullion47 x68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (area upto 0.75 sqm), compirising of UPVC multi chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanised mild steel section made from roll forming process of required length (shape& size according to UPVC profile), UPVC extruded glazing beads of appropriate dimension, EPDM gasket, GI fasteners 100x8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. ((Note: The unit rate quoted by contractor includes the cost of glass and includes necessary modification of ventelator according to the site requirement such as opening for exaust fan, lauvers etc and all other connected accessories. Net opening will be measured for payment purpose.) 11 S & F White/ColouredUPVC partition fixed complete all as per manufacturers instructions and following specifications all as directed:-(i) UPVCfixed partition frame shall be made ofmaterial confirming to IS 10151of extruded UPVCsection having over all dimension of 65 x 55having wall thickness 2mm ± 0.2mm. (ii) Corners of frame shall bejointed by MS galvanized brackets mitred and plastic welded.(iii) The profiles should be single chamber system which shall provide high insulation properties.(iv)Partition consisting of solid UPVC shutter with UPVC Panels not less than 6mm thick/ toughened glass not less than 10 mm thick, as per requirementfixed in frames with appropriate beading as per manufacturers specification. (v) All the fittings shall be provided with using self tapping screws. Note: The entire fixing shall be done as per manufacturers instructions and specification and as directed by Engr-in-Charge. For UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.all as specified and directed .The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. 12 M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 all as specified and as directed. 13 S&F in repairsblinds of approved make Roller type,Zebra pattern using Polyester/PVC/ Vinyl of approved colour/ shade and pattern including operating arrangement such as chord/thread, counterweight, connecting chain etc and necessary fittings complete all as specified and directed. Make: Vista/ Levolor/ Aerolux/ MAC. 14 M&L for precast solid block exceeding 10 cms in width 1:3:6 type C1 (using 20mm graded aggregate) and set in cement mortar 1:6 all as specified and as directed 15 M&L for PCC 1:4:8 type D2 with 40mmgraded stone aggregateas in sunken floor/toilet floor /roof slab/kitchen floor concrete finished the surfaces even and fair to receive top layer all as specified and as directed. 16 M&L cement concrete type B1 1:2:4 using 20mm graded stone aggregate 40mm thick as in flooring with using 3% WPC etc all as specified and as directed 17 M/L for non skid ceramic coloured tiles 7mm to 8 mmthick(square/rectangular)area of each tile exceeding 0.11 Sqm, but not exceeding 0.18 Sqm , in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified & directed. 18 M&L for glazed coloured ( 350 x 450 mm/600mm x300mm) x 7 mm th as in skirting/dado over & including 10mm thk rendering in CM 1:4 set onbrick/PCC Blockmasonry/concrete surface& jointed in neat cement sullry & pointed in white or coloured cement to match complete all as specifiedand directed. 19 Material and labour for Granite work with 20mm thick machine cut, Jet Black granite slabin single piece or two piece length, table rubbed and polished, laid over and including 20mm thick cement screed in cement mortar 1:4, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust and admixture of pigments to match with shade of granite stone as in cooking platforms, microwave platform, WHB counter topin steps, jambs, pillars, window-cills,etc, including cutting, polishing and rounding to edges of stone slabsetc., complete all as specified and as directed. 20 Supply and fixed in repair Vitreous china wash down water closet pan, pedestal pattern, colour white, closed pattern with flat bottom with and including white coloured PVC seat cover, mild steel chromium plated or aluminised hinging device flushing cistern and P/S trap including connections to drain(or outgoing pipe) andtaking down existing water closet etc., complete all as specified and as directed. Make : Cat No FLS-WHT-5353PPZ of Jaquar/ Cat No C8810/C8809(S-110/220) of Parryware/ Cat No 20151 (P-17.5) Cist -924154 of Hindware or equivalent all as specified and as directed 21 S&F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern)including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, urinal spreader, grating,waste pipe and Union for discharge pipe all as specified and as directed 22 Supply and fix in repair Vitreous china Wash Hand Basin, White, counter top oval type of size 550x450x200mm as per Cat No.FLS-WHT-5701 of Jaquar (or) C0431 Cascade NXT of Parryware or Cat No.10017 of Hindware or equivalent of other specified makes, fixed over an d including including32mm waste coupling, 32mm dia waste pipe750mm long etc.,including taking down existing one complete all as specified and as directed.Note: The unit rate quoted shall be deemed to include the cost of WHB, Granite slab, brackets, waste coupling and waste pipe. Make :Cat No FLS-WHT-5701 of Jaquar/ Cat No C 0407 of Parryware/ Cat No 10049 Hindware or equivalent. 23 Supply and fix in repairt angular stop cock 15mm bore, cast copper alloy, chromium plated, fancy type with long shank conforming to IS as per Cat No.CON-053KN of Jaquaror G3053A1 of Parryware, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and as directed. 24 S& F in repair Pillar cockcromium platedwith wall flange complete .screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipecomplete all as specified and directed. 25 S&F in repairs Bib cock (Two in one) with health faucet multi type including flexible hose complete all as specified and as directed. 26 Dismantling of cast iron /PVC pipe in of 150 mm dia and in any position all as specified and as directed. 27 Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore all as specified and as directed. 28 Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 20mm bore all as specified and as directed. 29 Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 25mm bore all as specified and as directed. 30 Supply and fix galvanised steel water tubing 15 mm bore,medium grade with all fittings and fixed completeto walls/ceiling or laid in floors complete all as specified and as directed. 31 Supply and fix galvanised steel water tubing 20 mm bore,medium grade with all fittings and fixed completeto walls/ceiling or laid in floors complete all as specified andn as directed. 32 Supply and fix 25 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed. 33 S&F in repairs 5.50mm thick looking mirror of size 1.85X1.20 M mounted on 6mm thick Plywood backing or AC sheet backing including framing with 1st class hard wood of size 40x40mm decorative type polished and fixed to wooden plugs with chromium plated brass screws and cupwashers/or chamferred glass from all sides fixed with steel screws all as specified and directed. 34 Supply and fixin repair Towel rail 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats all as specified and as directed. 35 S&F in repairs toilet paper holder brass CP rod to insert paper roll mounted and screwed to walls complete all as specified and as directed. 36 S&F in repair stainless steel soap dish of size min 100 mm dia or square or rectangular complete all as specified and as directed. 37 Supply and fixin repair 110 mm bore PVC (SWR) pipessingle socketed in any length with rubber ring joints fixed to walls/trenches complete all as specified and as directed. 38 Supply and fixin repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed. 39 Supply and fixin repairPVC connections 15mm size with brass nuts of length 600 mm eachcomplete all as specified and as directed. 40 Supply and fixin repair75 mm dia PVC floor trap with gratingincluding jointing to waste pipe with hole for waste pipewith 100 dia CP grating fix with cement mortarincluding jointing to waste pipe complete all as specified and as directed. 41 M&L 15mm thick rendering plaster onfair face of brick-work or concrete surfacein CM 1:6 complete all as specified and as directed . 42 M&L for preparation of newplastered surfaces of walls applying two coats of distemper, oil emulsion including alkali resistant primer over 3mm thick wall care putty complete all as specified and as directed. 43 M&L 15mm thick rendering plaster brick or concrete surfacein CM 1:4 as in external walls/chajja/manholes including adding water proofing compoundcomplete all as specified and as directed .(WPC will be measured and paid separately.) 44 Material and labour for applying two coat of exterior acrylic emulsion weather proof paint overa coat of primer including applying 3mm wall care putty and preparation of new plasterd surface all as directed. 45 M&L for vitrified double charged /Ultracharged jointless tiles 8-10mm thiock light/dark colour (Square/rectangulart) area of each tile n exc 0.36 Sqm as in floor etc set and jointed in neat cement slurry and pointing in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. 46 Supply only Liquid Water proofing compound. all as specified and as directed 47 M&L rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM 1:3 on ceiling and finishing the surface even and smooth without using extra cement complete as specified. 48 M&L for preparing new plasteredsurfaces of ceilling and applying two coats ofdistemper over a coat of primer and 3 mm wall acre putty all as specified and as directed. 49 M&L for preparation ofold plastered or unplastered surfaces of wallsand applying one coat of Oil bound distemper, white or tintedcomplete all as specified and directed. 50 M&L for preparation of oldplastered surfaces of ceiling applying one coat of distemper, oil emulsioncomplete all as specified and directed. 51 Taking down point wiring (light, fan, socket or power) complete , including fixture and fittings such as switches, ceiling roses, sockets, light fitting, bell etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as specified and directed. 52 M&L for point wiring concealed complete with 1.5 sqmm (nominal area) FRLS gradePVC insulated, unsheathed stranded copper conductor single core cable 1100 volts grade in and including PVCconduit medium grade complete with conduit fittings/accessories with provn of MS terminal boxes of suitable size including provn ofhousing ofswitches, and socketsetc including 1.5 sqmmFRLS grade PVC insulated unsheathed stranded copper conductor for earth continuity conductor and connected to common earth dolly for the followings :Note: The cost for concealed point wiring is deemed to be inclusive of cutting chases in stone masonary wall/roof/ floor for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 10cm girth. 53 One light point or one fan point controlled by one switch with cables 1.5 sq. mm size all as specified and directed. 54 One 3 pin socket outlet, 5 amps, independent, with cables 1.5 sq. mm size all as specified and directed. 55 All as per item No.52 above but wiring complete with 2.5Sqmm for 3 pin 15A socket multipurpose on independent board all as specified and directed. 56 M&L for Modular switch 1 way 6A, 1 moduleall as specified and directed. 57 M&L for Modular switch 1 way 16A,1 moduleall as specified and directed. 58 S&F Socket, 6A - 2/3 pin combined 2 module,all as specified and directed. 59 S&F Socket 6A/16A - 2/3 pin combined 2 moduleall as specified and directed. 60 S&F modular Metal flush box 3 module all as specified and directed. 61 S&F modular Metal flush box 6 module all as specified and directed. 62 S&F modular white cover plate with frame, 3 module all as specified and directed. 63 S&F modular white cover plate with frame, 6 module all as specified and directed. 64 Taking down Submain wiring with aluminium conductor along with PVC Conduit and Material and Labour for Submain wiring with 2 runs of FRLS gradePVC copper conductor cable 4 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 4 Sqmm drawn through and includingPVC Conduit pipe 20 mm dia with all fittings all as specified and directed.Note: The cost for concealed submain wiring is deemed to be inclusive of cutting chases in stone masonary wall/roof/ floor for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 10cm girth. 65 S&F Wall mounted, 18 W, LED 6000K (4 ft.) LED tube light batten, min lumen out put 100 lum/watts extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver, lamp color white including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.. 66 S&F Wall mounted, 10 W, LED 6000K (2 ft.) LED tube light batten, min lumen out put 100 lum/watts extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver, lamp color white including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.. 67 Supply and fix for ceiling rose 3 terminals PVC/Poly Carbonate isolated body incl base block complete all as specified. 68 Supply and fix Distribution boardsheet steel phosphatised powder coatedfor MCB/DB with copper bus bar and neutral link earthing stud (confirming to IS-13032, IS-8623) TPN DB 8 way double door typewith 200 amps rated bus bar 69 Supply and fix MCB SP 06 to 32 Amps, 240 Volts, 50 Hz AC supply complete all as specified and directed. 70 Supply and fix MCB SPN 40 Amps 240 Volts, 50 Hz AC supply complete all as specified and directed. 71 Taking down and Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm all as specified and directed.
