|
| 1 | Taken down/Dismantling ofplain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. |
| 2 | Demolition ofBrickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement morter. |
| 3 | Taken down damaged wooden frame with shutter exc 1 sq. m and n exc 2 sq. m each |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm hard/dense soil |
| 5 | M/L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard and dense soil. |
| 6 | M/L for Bricks, sub class B, laid flat, in floors, old size brick laid dry |
| 7 | S/F for filling of good quality loose earth / sand filling and leveling of earth in layers including watering and consolidation. |
| 8 | M/L for P.C.C.in foundations filling and mass concrete 1:3:6 Type C2, with 40mm graded aggregate,. |
| 9 | M/L for Reinforced Cement Concrete in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete M-20 (20mm graded aggregates) |
| 10 | M & L for mild steel TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia.; Complete all as specified and as directed by the Engineer-in-Charge. |
| 11 | M/L for wear proof topping 20mm thick as specified (incorporating an approved metalic floor hardner @ 3Kgs./Sq.m.) mixer with water proofing compound, laid on concrete floors and pavings, and finished even and smooth.(except metalic hardner). |
| 12 | Supply only metalic floor Hardner |
| 13 | M/L for Rendering 25mm thick cement plaster, using cement morter (1:4) on wall/ceiling / concrete surfaces and finish the surface even and smooth without using extra cement including coat.(204.80+3*58.32+41.12) |
| 14 | M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc with flat surface finish and fair finished.; Complete all as specified and as directed by the Engineer-in-Charge.(462.80+80.39) |
| 15 | M/L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar,complete Set in cement mortar 1:4 Type B1 1:2:4 |
| 16 | Cutting holes in brick walls built in cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cement moratr 1:3 or cement concrete 1:2:4 type B-1 as required, exc. 1/2 brick n. exc. 1 brick thick |
| 17 | S/f of Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws as specified |
| 18 | Supply , assembly and erection of GI sheet with TDF flange rectangular/square duct made out of \"L\" shaped hollow profile, duly factory boxed, incl all accessories such as Corner, Cleat, Carriage bolt, Gasket and appropriate sealant on longitudinal joints etc complete of size 18 Gauge. |
| 19 | S/F Plain Aluminioum sheeting Alloy 31000 H-4, thickness 0.71mm in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed). |
| 20 | Applying Two coats of Synthetic enamel paints (Berger/Asian/ICI) over preparation of new surfaces on steel surfaces of any description, over aluminium red oxide primer, above 10 cm in width or girth.(18.10+35.00+45.60+45.60) |
| 21 | M&L for applying two coats of Plastic emulsion paint on old surface of any description over 10cm girth or width over one coat of wall primer including surface preparation; Complete all as specified and as directed by the Engineer-in-Charge. (16.70+32.60+50.8+50.8) |
| 22 | S/F for gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or slidingwith and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, Fe-290(Gde E 165) |
| 23 | Supply and fixing factory made uPVC white color Sliding window Two track made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding , Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose), Area exceeding 2.00 sqm each. |
| 24 | Supply and fixing factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75 sqm.) comprising of uPVC multi- chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile offrame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) |
| 25 | Supply and fixing factory made uPVC white colour Two track two panels sliding glazed door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC multi-chambered frame, with in-built aluminium roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC, extruded glazing beads, uPVC extruded interlock and uPVC extruded line sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double SS rollers (weight bearing capacity to be 120 kg), G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) |
| 26 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Slidingmesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Area exceeding 2.00 sq.m each |
| 27 | Filling the gap in between uPVC frame & adjacent RCC/ Brick/ Stone work upto 5mm depth and 5mm width by providing weather silicon sealant over backer rod of approved quality as per the direction of Engineer-in-charge complete. |
| 28 | M & L for sheet glass 5.5mm thick, ordinary quality and glazing withoil putty packing in square exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge. |
| 29 | S/F for MS ERW PIPE -300 |
| 30 | S/F for MS ERW PIPE - 200 mm |
| 31 | M/L for Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.)Tee pieces single branch. \"Y\" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plug. 200mm to 300mm bore |
| 32 | M/L for Connecting pieces one end flanged and other socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth. |
| 33 | Supplying and laying of CPVC pipes 32mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 34 | Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock systemwith M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. |
| 35 | Hiring of JCB\"s (vertical arm maximum 20 m and Horizontal arm maximum 30m )including Driver, fuel and other necessary items for cleaning and dumping, lifting of material from work execution siteas per direction of Engg. In Charge. |
| 36 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louver |
| 37 | Supply and fixing LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 38 | M & L for One 3 pin socket outlet. 15 amps, independent, with cables 4 sq. mm size with copper conductor cables FRLS in PVC Conduict PVC single core sheathed cable |
| 39 | M & L for One lightpoint or one fan point controlled one switch with cables 2.5 sq. mm size wiring with copper conductor cables FRLS in PVC Conduict PVC single core sheathed cable |
| 40 | M&L 6 Way modular metal flush box |
| 41 | M&L 6 modular white cover plate with frame |
| 42 | M & L of Modular switch 1 way 6A, 1 module |
| 43 | M & L of Modular switch 1 way 16A, 1 module |
| 44 | S & F of Socket, 6A - 2/3 pin combined 2 module, |
| 45 | S & F Socket 6A/16A - 2/3 pin combined 2 module, |
| 46 | M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor,4core , 1100 volts grade, csec. area 16 sq. mm→ |
| 47 | M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire. |
| 48 | M&L For Sub main wiring along with single core earthwire with2x 6.0 SQ MM in PVC Insulated Copper conductor with 1x6.0 mm earth wire with Suitable PVC conduit pipe &accessories. As directed by the Engineer-in-charge. |
| 49 | M&L For Sub main wiring along with single core earthwire with2x 4SQ MMin PVC insulated Copper conductor with 1x4 sq. mm earth wire with Suitable PVC conduit pipe &accessories. As directed by the Engineer-in-charge. |
| 50 | S & F of Sheet metal enclosures for single door 415Vtriple pole and neutral 8 way with 200 Amps rated bus bar |
| 51 | Supply and fixing amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.SP 6 To 32 AMP |
| 52 | Supply and fixing amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.SPN 32 AMP |
| 53 | Supply and fixing of MCCB 4 Pole , 415 V, 63 Ampswith breaking capacity 16 KA with enclosure Complete as directed by Engineer-in-charge. |
| 54 | M&L of MCCB 3 Pole , 415 V, Adjustable type 250 Amps. with breaking capacity 36 KA with enclosure Complete as directed by Engineer-in-charge. |
| 55 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) |
| 56 | Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre |
| 57 | M and L for 12 mm Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) |
