Supply, Installation And Commissioning Of Equipment And Machineries For The Fitter Trade.- 1 Fitter 2 A. Pneumatic Trainer Kit, each consisting of the following matching components and accessories: I. Single acting cylinder(Max. stroke length 50mm, Bore dia. 20mm). II. Double acting cylinder(Max. stroke length 100mm, Bore dia. 20mm, magnetic type).III. 3/2-way valve(manually-actuated, Normally closed) 02 nos . IV.3/2-way valve(Pneumatically-actuated, spring return). V. One-way flow control valve2 Nos. VI. 5/2-way valve (with manually-operative switch). VII. 5/2-way valve (Pneumatically-actuated, spring return). VIII. 5/2-way Pneumatically-actuated valve (double pilot). IX. 3/2-way roller nlevel valve (direct actuation Normally) 02 Nos. X. Shuttle valve(OR).XI. Two-pressure valve(AND). XII. Pressure gauge(0-16 bar) . XIII.Manifold with self-closing(NRV, 6-way). XIV. Pushbutton station for electrical signal input(with 3 illuminated momentary-contact switches(1 NO + 1 NC) and 1 illuminated maintained-contact switch (1 NO + 1 NC), Contact load 2A).XV. Relay station (with 3 relays each with 4 contact sets (3NO+1NC or change-over type), 5A). XVI. 3/2-way single solenoid valve(with LED). XVII. 5/2-way single solenoid valve (with manual override and LED). XVIII. 5/2-way double solenoid valve with manual override andLED.XIX. Power supply unit, Input voltage 85 – 265 V AC, Output voltage: 24 V DC, Output current: max. 4.5 A,short-circuit-proof. XX. Profile plate, Anodised Aluminium (1100x700mm, with carriers, mounting frames and mounting accessories(to be fitted onto the pneumatic workstation)). B. Pneumatic workstation with 40square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metalik full panel drawer slide: (1. Worktable- Size (approx) L1200 mm x W900 mm X H900mm, with 4 castorwheels including 2 lockable wheels at the front side, 2. Drawer- Size (approx) - L460mm x W495mm x H825mm and 3. Drawer SlideHeight (approx) 85mm). C. Carrier for mounting components, such as PB & relay boxes. D. Cut section model for pneumatic components. 3 A. Hydraulic Trainer Kit, each consisting of the following matching components and accessories : I. Hydraulic power pack (with 1. external gear pump having a delivery rate of 2.5lpm, (approx) @1400rpm operating pressure 60bar, couplled to a single phase AC motor (230V AC) having start capacitor and ON/OFF switch and overload protection, 2. Pressure relief valve adjustable from 0-60 bar, 3. Oil reservoir, ≥5 Litres capacity having sight glass, drain screw, air filter, and P and T ports. II. Pressure relief valve(pilot operated). III. Drip tray, steel (size 1160mm x 760mm ). IV.Pressure gauge (Glycerin-damped, indication range of: 0-100 bars). V. Four-way distributor (with five ports, equipped with a pressure gauge). VI. Double acting hydraulic cylinder (with a control cam, piston dia. 16mm, piston rod dia. 10mm, stroke length 200mm).VII. Suitable weight (for vertical loading of hydraulic cylinder). VIII. Mounting kit for weight (for realizing pulling and pushing load).IX. 3/2-way directional control valve (with hand lever actuation). X. 4/2-way directional control valve (with hand lever actuation).XI. 4/3-way directional control valve (closed centre position, with hand lever actuation). XII. Non-return valve. XIII. Pilot operated check valve (Pilotto open) . XIV. One-way flow control valve (with intregated check valve). XV. T-connector with self -sealing coupling nipples (2 Nos.) and quick coupling socket (1 No) . XVI. Profile plate (Anodized aluminium, 1100 x700mm , with carriers, mounting frames and mounting accessories(to be fitted onto the hydraulic workstation)). B. Hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metalic full panel drawer slide: (1. Worktable - Size(approx) L 1200mm x W 900mm x H 900mm, with four castor wheels including two lockable wheels at the frontside, 2. Drawer-Size(approx)- L 460mm x W 495mm x H 158mm each, and overall size of drawer unit (approx) L 470mm x W495mm x H 825mm and 3. Drawer slide height (approx) 85mm).C. Cut-section models for hydraulic components .
