Supply, Installation And Commissioning Of Equipment And Machinery Of 06Nostrade Electrical, Fitter, Smw, Wireman, Machinist, Turner.- 1 06 nos Trade Electrical, Fitter, SMW, Wireman, Machinist, Turner 2 D.C. Compound Generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, (SPECIFICATION- D.C. Compound Generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, 2.5 KW, 220V &3phase Squirrel cage Induction Motor, 5HP, 440V, with control panel & star delta starter ) 3 Ceiling fan coil Winding Machine.250V, 50 Hz, 1- Ф, with speed control 4 Primary current injection set .220V, 50 Hz, 1-Ф, output current - 200 A (min) with timer 5 SS and SC centre lathe(all geared) with minimum specification (Centre height 150mm and centre distance 1000mm along with 3 & 4 jaw chucks, auto feed system, safety guard, taper turning attachment, motorized coolant system, lighting arrangement & standard accessories. 6 Compressor unit(Suitable for Pressure : 8 bar, Delivery:50lpm(or more), Reservoir capacity: 24 Litres(or more), 230V, 50Hz, with pressure regulator and water separator) 7 A. Pneumatic Trainer Kit, each consisting of the following matching components and accessories: I. Single acting cylinder(Max. stroke length 50mm, Bore dia. 20mm). II. Double acting cylinder(Max. stroke length 100mm, Bore dia. 20mm, magnetic type). III. 3/2-way valve(manually-actuated, Normally closed) 02 nos . IV.3/2-way valve(Pneumatically-actuated, spring return). V. One-way flow control valve2 Nos. VI. 5/2-way valve (with manually-operative switch). VII. 5/2-way valve (Pneumatically- actuated, spring return). VIII. 5/2-way Pneumatically-actuated valve (double pilot). IX. 3/2-way roller nlevel valve (direct actuation Normally) 02 Nos. X. Shuttle valve(OR). XI. Two-pressure valve(AND). XII. Pressure gauge(0-16 bar) . XIII.Manifold with self- closing(NRV, 6-way). XIV. Pushbutton station for electrical signal input(with 3 illuminated momentary-contact switches(1 NO + 1 NC) and 1 illuminated maintained- contact switch (1 NO + 1 NC), Contact load 2A).XV. Relay station (with 3 relays each with 4 contact sets (3NO+1NC or change-over type), 5A). XVI. 3/2-way single solenoid valve(with LED). XVII. 5/2-way single solenoid valve (with manual override and LED). XVIII. 5/2-way double solenoid valve with manual override andLED.XIX. Power supply unit, Input voltage 85 – 265 V AC, Output voltage: 24 V DC, Output current: max. 4.5 A,short-circuit-proof. XX. Profile plate, Anodised Aluminium (1100x700mm, with carriers, mounting frames and mounting accessories(to be fitted onto the pneumatic workstation)). B. Pneumatic workstation with 40square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metalik full panel drawer slide: (1. Worktable- Size (approx) L1200 mm x W900 mm X H900mm, with 4 castor wheels including 2 lockable wheels at the front side, 2. Drawer- Size (approx) - L460mm x W495mm x H825mm and 3. Drawer SlideHeight (approx) 85mm). C. Carrier for mounting components, such as PB & relay boxes. D. Cut section model for pneumatic components. 8 A. Hydraulic Trainer Kit, each consisting of the following matching components and accessories : I. Hydraulic power pack (with 1. external gear pump having a delivery rate of 2.5lpm, (approx) @1400rpm operating pressure 60bar, couplled to a single phase AC motor (230V AC) having start capacitor and ON/OFF switch and overload protection, 2. Pressure relief valve adjustable from 0-60 bar, 3. Oil reservoir, ≥5 Litres capacity having sight glass, drain screw, air filter, and P and T ports. II. Pressure relief valve(pilot operated). III. Drip tray, steel (size 1160mm x 760mm ). IV.Pressure gauge (Glycerin-damped, indication range of: 0-100 bars). V. Four-way distributor (with five ports, equipped with a pressure gauge). VI. Double acting hydraulic cylinder (with a control cam, piston dia. 16mm, piston rod dia. 10mm, stroke length 200mm).VII. Suitable weight (for vertical loading of hydraulic cylinder). VIII. Mounting kit for weight (for realizing pulling and pushing load).IX. 3/2-waydirectional control valve (with hand lever actuation). X. 4/2-way directional control valve (with hand lever actuation).XI. 4/3-way directional control valve (closed centre position, with hand lever actuation). XII. Non-return valve. XIII. Pilot operated check valve (Pilotto open) . XIV. One-way flow control valve (with intregated check valve). XV. T-connector with self -sealing coupling nipples (2 Nos.) and quick coupling socket (1 No) . XVI. Profile plate (Anodized aluminium, 1100 x700mm , with carriers, mounting frames and mounting accessories(to be fitted onto the hydraulic workstation)). B. Hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metalic full panel drawer slide: (1. Worktable - Size(approx) L 1200mm x W 900mm x H 900mm, with four castor wheels including two lockable wheels at the frontside, 2. Drawer-Size(approx)- L 460mm x W 495mm x H 158mm each, and overall size of drawer unit (approx) L 470mm x W495mm x H 825mm and 3. Drawer slide height (approx) 85mm).C. Cut-section models for hydraulic components . 9 Spot & Seam Welding Machine 10 Conduit pipe cutting and threading machine adjustable for 15 mm to 30 mm. 11 Tower Ladder on type Wheels, min 10ft max 30 ft 12 Solar Street Light ,(Specification - 12V, 75Ah battery, 75 Wp solar panel, 12V, 10A dusk to dawn charge controller, 60 W LED lights and 9 m height pole all dismountable12V, 75Ah battery, 75 Wp solar panel, 12V, 10A dusk to dawn charge controller, 60 W LED lights and 9 m height pole all dismountable 13 Solar Traffic Light ,(specification -12V, 75Ah battery, 75 Wp solar panel, 12V, 10A dusk to dawn charge controller, 15 W LED lights with suitable colors and 9 m height pole all dismountable) 14 Drill H.S.S. taper shank ,(6 mm to 12 mm in step of 0.5 mm) 15 Bench vice ,100 mm jaw 16 Machine Vice ,Swivel Base -150 mm 17 Radius turning attachment , 18 Milling Cutter - Shell End Mill ,Ø 75 mm x 50 x 27 mm, Preferably Inserted Tip Type 19 Involute Gear cutter ,Size 2,2.5,3 module 20° pressure angle 20 Direct reading vernier caliper ,0- 300 (direct reading with dial) 21 Vernier bevel protractor ,with 150 m blade 22 Telescopic Gauge ,8 mm to 150 mm 23 Limit plug gauges ,5 mm to 25 mm by 2.5 mm 24 Ring gauges ,5 mm to 25 m by 2.5 mm (GO & NO GO) 25 Planer gauge standard size 26 Coventry Type Die Head (Self Opening) 27 Digimatic Electronic Vernier Caliper - 200 mm - Best quality 28 Digimatic Electronic OD Micrometer {( 0 to 25 mm) LC 0.001 mm.} Best quality
