Tender For Construction Of Godown 1080 Mt - Construction Of Warehouse 1080 Mt - CIVIL WORK 2 Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means 3 Excavation for foundation in earth, soils of all types, sand, gravel and soft-murrum, including removing the excavated material up to a distance of 50 meters beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) By Mechanical Means 4 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand-packing and compacting etc. complete. 5 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer in-charge in layers of 15 cm to 20 cm including watering and compaction etc. complete. 6 Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centring, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc.) 7 Providing and laying in situ /Ready Mixcement concreteM-20of trap / granite /quartzite/ gneissmetal for R.C.C. workin foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchionsetc. including bailing out water,Steel centring formwork, laying/pumpingcover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) 8 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc.) 9 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centring, formwork, cover blocks, laying/pumping, compaction and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). With fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan Mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) 10 Providing andlaying Castin situ/Ready Mix cement concrete M-20 of trap/ granite /quartzite/gneiss metalforR.C.C. slabsand landings as perdetailed designsand drawingsincludingsteelcentering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surfaceorrougheningifspecialfinishistobe providedandcuringetc.complete,(Excluding reinforcementandstructuralsteel).withfullyautomatic microprocessorbasedPLCwithSCADAenabled reversibleDrum Typemixer/concreteBatchmixplant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade). 11 Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centring, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan Mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) 12 Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. Including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 13 Providing and fixing in position HCRM / CRS (CorrosionResistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. Including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. 14 Providing secondclassBurntBrickmasonrywithconventional/I.S.typebricksincement mortar 1:6 in plinth as backing in composite masonry including bailing out water manually, striking joints, raking out joints and watering etc Complete. 15 Providing Second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in Superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete. 16 Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete 17 Providing External cement plaster 15 mm thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positionsincluding scaffolding and curingetc. Complete. 18 Providing and laying in situ Tremix Cement Concrete M-20 with tremix treatment for 100 mm thickness for flooring with groove cutting of 4mm wide and 20 mm deep with necessary refilling with bitumen etc. complete. 19 Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sq.m as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. 20 Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. 21 Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete. 22 Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. 23 Providing and fixing screw down 15 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete 24 Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and topsection 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineer-in-charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self-locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc., complete. With colour anodising without box 25 Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 26 Providing and fixing H.D.P container one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 litres 27 PEB WORK 28 Supplying,Fabricating,erecting & fixing in position of steel structures at all elevations using fusion welding quality steel E-350 (Fe 490) conforming to IS :2062 -2006. Rate shall be include cost of cutting,welding,splice plates,& packing plates,transporting,straighting ,cleaning,fabricating,& erecting in position weled /bolted structrural steel work in columns,beams,trusses,purlins,platforms,ladder,momorails,staircass ,supports,strenghting of steel members,etc.at site to line & level,supply of approvedbolts/nuts/washers etc.complete as per drawing including painting as per G/4,G/5,G/6 before erection& all material & labour chargesetc.complete& including sand blasting & painted withone coats og enamel paint (Berger EPILUX SG-HHI 664002) of 35-50 micron each coat with air less spary gun over a coat of zinc chromate primer-35-35 micron etc. complete as shownin drawings as per specifications and as directed by Enginner- in-charge (The Rate quoted shall include cost of bolts, nuts,washers,welding & electrodes required fot complete work). 29 Supplying,Fabricating,erectingof Cold Formed Light GaugestructuralSteel members conforming to IS:801/IS: 811 hot dip galvanised to IS:4759-96 including cutting,welding or bolting,splice plates , transporting,straghtnening,cleaning,fabricating & erececting in position 30 Supplying & Fixing ofPPGI Sheets ot 0.5 mm thick as shown in drawingor as directed by engineer in charge.( Essar Make) 31 Supplying & Fixing of 0.5 mm thk PPGL roof accessories as per drawingor as directed by engineer in charge. 32 Supplying & fabricating & erecting in position PPGI Eaves Gutter of required size with stop ends, all fixing accessories, dtop ends,etc. all elevations levels & heights incluiding, alinging,leveling,providing& fixing nut bolts,washers etc.as directed by engineer in charge. 33 Providing & Fixing of the rain water down take pipes Of PPGI , the sectional area of rain water down take pipe provided shallbe generally at the rate of 1 Sq.cm/ 70 to 80 Sq. decimetre of roof area drained. No Spout shall be less than 80 mm in diameter. The spacing of spouts shallbe arranged to suit the position of opening in the wall including all materials & labours charges etc. as per drawing or as directed by engineer in charge. 34 Turbo Ventilator 24 : Providing and fixing wind operated turbo ventilator system of various sizes over the existing roof including cutting CGI sheet, proper fixing in position to true line and level with all fixtures and fastenings includign etc. complete. 35 ELECTRIFICATION 36 Supplying,erecting&terminatingXLPEarmouredcable3 core6sq.mm.copperconductorcontinuous5.48sq.mm. (12SWG)G.I.earthwirecompleteerectedwithglands& lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 37 Makingtrenchofsuitablewidthanddepthinhardmurum/ tar roadfor layingprovided LTcable upto andincluding 16 sq. mm complete as per specification no. CW-EXNCTR 38 Makingtrenchofsuitablewidthanddepthinsoftsoilfor layingprovidedLTcableuptoandincluding16sq.mm complete as per specification no. CW-EXN-CTR 39 Supplying & erecting mains PVC unarmoured cable 1100Volt 40 Supplying & erecting weatherproof powder coated distribution board 4 way with 2 x 6/10 Amp S. P. M. C. B. with industrialtwopinplugsocket10Aand3pinplugtop10A with top cover necessary connection etc complete with approved make. 41 ProvidingpointwiringforstreetlightwithPVCunarmoured cable1100VoltgradeISImark3core1.5sqmmstranded/ solid copper erected on wall with G. I. Saddle duly painted @ 0,25 m C/C rigidly grouted in the wall with the help of plated 42 Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base. 43 Supplying and erecting LED street light fitting suitable for20 to25W,withPF>0.95classIP65andabovehousingof pressurediecastaluminiumalloyandheatsinkextruded aluminium complete as per specification No FG-ODF/FLS 44 SupplyinganderectingstreetlightWallbracketmadefrom 40 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB 45 Providing earthingwith galvanizediron earthplate size60 x 60x 0.6cmcompletewithallmaterials,testing&recording the results as per specification no. EA-EP 46 Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP 47 Supplying, erecting & marking DPMCB 6A to 32A,C- series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB 48 Supplying,erecting&markingSPMCB6Ato 32A,B- series (for lighting) in provided distribution board as per specification no. SW-SWR/MCB 49 SupplyinganderectingGIsheet1.6mm(16SWG)tobe usedforfabricationofboxespanelboardsetc.including cutting,bending,drilling,welding,rivetingetc.andpainting with one coat of red lead paint and 2 coats of enamel paint. 50 Supplying and erecting marine plywood 18/19 mm thick fixed towall or onprovided panel board withnecessary materials such as screws, wall fasteners, supports, nut bolts etc. 51 Supplyinganderectingtriplepoleandneutraldistribution board(TPNDB)surface/flushmountedsuitableforSPMCB of 12 ways on iron / GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB 52 Supplying&erectingG.I.pipe‘A’ class25mmdia.erected forenclosing XLPE armoured cable onwall/pole asper specification no. CB-CE 53 Supplying & erecting G.I. pipe ‘A’ class 40 mmdia. erected forenclosing XLPE armoured cable onwall/pole asper specification no. CB-CE 54 Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosingcable below ground/road surface, to required depth complete. 55 Supplying&erecting18guageM.S.Boxpowdercoated (4x4) 3 way for mains connection. 56 Supplying & erecting Siemens type brass cable glands for 3 to4core6sq.mm./2to4core10sq.mm.forXLPE armoured cable as per specification No. CB-GL 57 Supplying shockproof type hand lamp with lamp holder, bulb/ lamp100Wguardedglass and30 mtr.3 corePVC flexible 58 Point wiring for independent plug in 20 mm ISI markedHMS PVCconduitwith1.5sq.mm(2+1E)FRLSHgrade copper wire, flush type switch, earthing and requiredaccessories as per specification No: WG-PW/SW 59 SupplyinganderectingStreetlightbracketmadefrom25 mm. dia ‗B‘ class G.I. Pipe, 0.6 min length along with pole capof300mmlengthand80mmdiadulyweldedwith provided leads as per specification no. FG-BKT/BPC 60 Supplying&erectingmainswith2x2.5Sq.mmstranded copper PVC insulated wire with 2 x 1.5Sq.mmcopper PVC wire in PVC casing - caping20 mm on wall / ceiling. 61 Supplying&erectingmainwith2x4.00Sq.mmstranded copper PVC insulated wire with 2 x 1.5Sq.mmcopper PVC wire in PVC casing - capingon wall / ceiling. 62 Supplying and erecting double pole switch surface type/ flush type240V,32Awithindicator lamp&fuseas per specification no. SW-SWR/BDP. 63 Supplying and erecting double pole metal clad switch withHC type fuse and neutral link 240V, 32A on iron / GI frame as per specification no. SW-SWR/MDP .. 64 Supplying&erecting3W,230VintegraltypeLEDLamp suitable for B-22/E-27 base. 65 Supplying and erecting T8 Fluorescent tube day light 1200mm 36 W 66 Supplying&erectingreadytouseRetrofitT8LED18/20 tubelightwithpolycarbonatebody,heatsink,integratedHF electronicdrivercomplete&compatibletoT8/T12LED luminaire by disconnecting starter & ballast if necessary. 67 Supplying and erecting regular/ standard model ceiling fan of 900/1050mm.sweepcompleteerectedinpositionasper specification no. FG-FN/CF 68 Supplying and fixing wiremesh (Jali) cover suitable for fitting / fanorforanypurpose,completewithnecessarymaterials. The jali cover shall be made from good quality G.I. wire mesh 69 Supplyinganderectingdingdong/electronicmusicaltype call bell with heavy duty coil suitable to operate on 230V A.C. supplyerectedonpolisheddoublewoodenblock/sunmica block of suitable size 70 SupplyinganderectingstreetlightWallbracketmadefrom 25 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB 71 Supplying & erecting CRCA sheet metal one wayenclosures suitable for DP MCB /TP MCB /FP MCB erected on angle iron/GI frame complete. 72 Supplying erecting and marking four pole isolators only switch version of miniature circuit breakers of 40A in provided distribution board complete. 73 APPROACH BITUMIN ROAD 74 Trimming of grass, shurbs andweeds from the roadway shoulders/berms and disposing off the same to suitable locations etc. complete As Directed by Engineer In Charge 75 Excavationfor roadway inearth, soilofall sorts, sand,gravel or soft murum including dressing section to the required grade, camber and sideslopesandconveying theexcavated materialswithall lifts up to alead of 50m. and spreading for embankment or stacking as directed 76 Excavation for roadway in hard murum and boulder including dressing section to the cum required grade, camberand side slopes and conveying the excavated materials withall lifts up to alead of 50m. And spreading for embankment or stacking as directed. 77 Providingsolingusing80mmsizetrapmetal in15cm. layer including filling void with cum Crushed sand/grit, ramming, watering etc. complete. 78 Supplying trapstonemetal of required size by bringing the boulders/Rubbleat the road side breaking them to required gradation including conveying the boulders/ Rubble and stacking thebrokenmetal etc. complete. (Prior approval of samplestackofbrokenmetalbytheEx.Engineer isnecessary thedateofapprovalwill formpartof themeasurements)a) 80 mm Metal ,By breaking rubble obtained by blasting. (Hand broken). with prior approval of concerned Superitending Engineer. 79 Supplying trapstonemetal of required sizebybringing the boulders/Rubbleat the road side breaking them to required gradation including conveying the boulders/ Rubble and stacking the broken metal etc. complete. (Prior approval of sample stack of broken metal by the Ex .Engineer isnecessary thedate of approval will form part of theme asurements)a)40 mm Metal, By breaking rubble obtained by blasting. (Hand broken). with prior approval of concerned Superitending Enginee 80 Spreading80mmmetal for road work including sectiononget complete as directed by Engineer in charge 81 Spreading 40 mm metal for road work including sectiononget complete as directed by Engineer in charge . 82 Supplying hardmurum/ kankar at the road site, including conveying and stacking complete. 83 Spreadinghardmurum/ softmurrum/ gravel or kankar for side width complete 84 Compacting the subgrade/ gravel/ oversizemetal (200 mm loose) layers for all width withVibratory roll erhaving weight 8 to10MT. includingnecessary, labour, materials and artificial wateringcomplete 85 Compacting thehardmurumsidewidths including laying in layers on each sidewith vibratory roller including artificial watering etc. complete. MORTH 408 86 Providing and constructing 75 mm. thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40 mm. stone metal layers 100% crusher broken metal with conical crusher plant heating and spraying the bitumen of specified grade @ 2 Kilogram/Square Metre, spreading 12mm.size chips compacting with three wheel static roller having weight 8 to 10 MT. to achive the desireddegree of compactionas per Technical Specification Clause 506 etc. complete. (VG-30 bulk bitumen ) 87 Providing and applying tack coat on the prepared surface heating by fames in Boiler and spraying bitumen set footedin bitumen boller onB.T. surface 2.5 kg/10 sqm.(VG-30 bulk bitumen rates are considered to arrive at rates) MORTH 503 88 Open Graded Premix Surfacing-Providing and Laying OGC20 mm thickness composed of 13.2 mm to5.6 mm aggregates premixed with bituminousbin dertransported to site with VTS, laid over a previously prepared surface, finished to the requiredgrade, level, alignment, and rolling toachieve the desired compaction but excluding prime/ tackand Seal coat. For Bitumen of specifiedgrade--USING drum mix type hotmix plant with SCADA, Paver and Vibratory roller ( Over MPM Surface)(VG-30 bulk bitumenrates are considered to arriveat rates) MORTH 511 89 9MM SEAL COAT: Providing and laying of Type A9 mm premix seal coat with HMP of Sq mapropriate capacity crushed stone chiping 6.7mmsize and penetration bitumen of specified grade @ 1.2 kg/Sq.m, preparing existing road surface by mechanical means, spreading chips and rolling, bystatic roller havingweight 8 to10MTetc. complete. (VG-30bulk bitumen rates are considered to arrive at rates) 90 Providing & fixing R. C. C. 1:2:4 guard stones as per type design including painting numbering fixing in std. Size C. C. 1:4:8 block complete 91 ROYALTY CHARGES 92 Sand 93 Murun 94 MATERIAL LAB TESTING 95 Sand- Site test, Gradation, fineness modulus, silt and clay content 96 Aggregate/Crush material a) Carrying out water absorption 97 b)Specific gravity 98 c) Inpact Gravitygravity 99 d) crushing vlaue 100 Cement- Cement- Stabdard Consistency fineness, Specific gravity, Setting Time Initial And Final compressive strenght 101 Cement Concrete- Compressive Strength set of 3 cubes per 1 test 102 Mix Design M20 103 TMT steel bars- Steel - Tensile strength,Yield stress, ultimate tensile stress,%elongation, weight per running meter, Bend/Rebend test.(Set of 3 Bars) upto 16 mm (set of 3 bar) 104 TMT steel bars- Steel - Tensile strength,Yield stress, ultimate tensile stress, % elongation, weight per running meter, Bend/Rebend test.(Set of 3 Bars) Above 16 mm (set of 3 bar) 105 Bricks: Crushing value Water aborption,Specific gravity 106 ESHS 107 ESHS (Environment Safty and Health ManagementLabour Facilities (Lump- Sum Amount )
