}

Tender For Certain Repairs To Mes Installation Under Ge (A) No 1 Jodhpur, jodhpur-Rajasthan

Military Engineer Services has published Tender For Certain Repairs To Mes Installation Under Ge (A) No 1 Jodhpur. Submission Date for this Tender is 22-07-2025. Paver Blocking Tenders in jodhpur Rajasthan. Bidders can get complete Tender details and download the document.




Tender Notice

49944690
Tender For Certain Repairs To Mes Installation Under Ge (A) No 1 Jodhpur
Tender
Indian
Rajasthan
Jodhpur
22-07-2025

Tender Documents

Tender Details

Tender For Certain Repairs To Mes Installation Under Ge (A) No 1 Jodhpur; 1 Demolition of cement concrete (unreinforced)in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed. 2 Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specifide. 3 Taking down chowkhats or framewith shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as directed. 4 Taking down chowkhats or framewith shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each, complete all as directed. 5 Taking down shutters of any description area not exceeding 1 Sqm eachcomplete all as specified and as directed. 6 Taking down shutters of any description area exceeding 1.0 Sqm but not exceeding 2 Sqm eachand refixing in same position, complete all as specified and as directed. 7 Taking down steel windows/ventilator with frame of any description and any sizecomplete 8 Demoltion of cement cocrete padding of water proofing treatment from roof pading taking down bituminous polythene sheets plaster etc overall thickness n.exc 200mm , cleaning of concete surfaces by wire brushres scrubbing down water and removing the dust debris etc. to a distance 50 mtre but n.exc 250 mtr from the site,complete all as directed. 9 M&Lfor plain cement concrete 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregate), as in roofpaddingover roof for making good depression / undulation to make the existing as filling in depression of roof slab, complete all as specified & directed. 10 M&L forneat cement slurry @ 3.00 kg/Sqm and screeding / bedding layer of 10 mm thickin CM 1:3 mixed with water proofing compound as per manufacturer instructions over theRCC roof slab for laying of water proofing treatmentincluding providing the following as roof treatment complete all as specified andas directed : - (a)FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastered surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen confoRMing to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 3.00mm having weight not less than 3.00 Kg/Sqm, mineral gravel finish on top, using torch application method with minimum 10cm side lap and 15cm end lap complete . (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen confoRMing to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : 40 mm thick plain cement concrete 1:2:4 (using 20 mm stone crushed aggregate) as in roof padding, including WPC as per manufacturer instruction. NOTE :- 1. A Information Tablet will be put up in the front side wall of the buildings where thiswork will be done. All building/structure shall be provided with plaque (tablet) furnishing the information as per PS clause, in plaster engraving in and painted as directed by GE2.WPC shall be measured and paid separately under respective item. 11 M&L for cleaning and preparation of existing surface including Cutting and grubbing of bushes / shrubs all and laying graded 40 mm graded coarse aggregate, all as directed 12 Taking down oldu/s existing rolling shutter from existing poition, including all necessary T&P, complete all as specified and directed. 13 S&F 1.00mm thick lath Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed. 14 Supply and fixing ball bearing of rollingof suitable size and description, complete all as specified and directed. 15 M&L for Safety lever locks mild steel with 4 levers for rolling shutters, complete all as specified and directed. 16 S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and drawings, complete all as specified and directed. 17 S&F factory made solid panel pvc doorshutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed. 18 M&L for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, ,hollow pipe etc complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, complete all as specified and directed. 19 S&F 2nd class hard wood plain framed paneled shutter 35mm thick with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board upto commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated (Factory made shutters), complete all as specified and directed. 20 S&F glavanised steel wire cloth, 0.56mm nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tack or galvanised wire stapples complete all as specified and as directed. 21 S&F stainless steel butt hinges 100 mm size fixed to frames with cadmium plated screws, complete all as specified and directed. 22 S&F 100mm size MS butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and as directed. 23 S & F 100mm long, mild steel single action spring hinge,complete all as specified and as directed. 24 S& F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed. 25 S&F tower bolts anodised aluminium body 150 mm size, complete all as specified and directed. 26 S&F 150 mm size anodised aluminium handles extruded section, complete all as specified and directed. 27 S&F in repair Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3 universal type,suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed. 28 Taking down carefully cement conc /spalled out concrete fromRCC roof projections, cilinigs ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc., and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed. 29 M&L for cleaning the existingreinf of slabs , chajjas etc& applying a coat of SIKA RUSTOFF 11 to remove the loose rust particles etc & throughly cleaning the surface.,complete all as specified and as directed. 30 M&L for Applying a coat of bond coat made with cement slurry(1 part cement to 1.5 -2 parts water)mixed with admixtureLATEX POWERmixed @5 Kg per 50 kgof cement & applying to the conc surfaces @ 200 gm/sqm to obtain tack,complete all as specified and as directed. 31 M&L for 15 -20 mm thick rendering in CM 1:1:2 using1 part of cement 1 part 2-3 mm screenings of stone agg & 2 parts coarse sandover the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPERadmixture @ 100 gm /50kg of cement & finishing the surface even & rough to receive final rendering coat,complete all as specified and as directed. 32 M&L for 5 mm thick rendering in CM 1:3 & finishing the surface even & smooth w/o using extra cement,complete all as specified and as directed. 33 Hacking out old broken glass (any thickness, size, quality or description) from metal frame incld punching or drilling out old glazing pins/ spring clips and provding and fixing new ones, complete all as specified and as directed. 34 S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed. 35 S & F for powder coated anodized Aluminium Frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. 36 S & F for powder coated anodized aluminium door shutters, aluminium section weighing 0.55Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door hinges, anodised aluminium snap beading screws etc. complete all as specified. 37 S &F for powder coated anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluninium fittings such as peg stays 150mm long (1 No) hinges type B-21 100 mm long (2 No) suitable handle (1 No) in each shutter complete all as specified 38 S&F Sheet glass 4.80mm thick, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sq.m in each pane complete all as specified and directed. 39 S&F for4 mm thick figurred, pin headed glass ordinary quality & glazingwith oil putty in square n exc 0.50sqm ineach pane, complete all as specified and as directed by Engr-in-Charge. 40 S&F in replacementof Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty & fixed 41 S&F in replacementmortice latch with two loovers (Vertical type) mild steel body 100mm long and fixed. 42 M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring, incld. finishing the surface even & rough to receive tiling etc., complete all as specified and as directed. 43 M&L 75 mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base as in floor complete all as specified and as directed . 44 S&F 28-30mm thickprecast chequered tilesany shape rubberised finish Lacquer coated with top 4-5 mm with anti abrasive material all as per sample laid over cement sand screed (measured seprately) jointing & pointing in neat cement mixed with pigment over 15 mm screed bed in cm 1:4 complete all as directed at site 45 Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; 46 S&F machine made precast cement concrete curb stone blocks using Cement concrete 1:3:6 type C1 (20mm graded stone agg)set in CM 1:6 all as directed by Engr-in-Charge 47 M&L 50 mm thick PCC 1:3:6type C1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval,complete all as specified and directed. 48 M&L ready-mix Cement concrete work in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre thickness of concrete 25 cm or less complete all as specified and directed by Engineer-in Chage 49 M&L PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foundation , filling, sub base and mass concerete complete all as specified and as directed. 50 M&L forglazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirtingetc, set and jointed in neat cement slurry and pointed in white or colouredcement to match the shade of tiles,over & including M&L 10mm thick backing coat in CM (1:4), (including Highlighter pattern),complete all as specified and directed. 51 M&L for joint free non skid ceramic coloured tiles (premium quality) of size 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as infloors etc set and jointed in neat cementslurry and pointed in white or coloured cementto match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6complete all as specified and directed. 52 All as per item No. 51.00 here-in-above, but size of tile exceeding 0.11 Sqm but n.exc. 0.18 sqm . 53 All as per item No. 51.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed. 54 M&L for light shade vitrified ceramic tiles, 10 mm thick (square/ rectagular) polished, area of each tiles exceeding 0.36 sqm butnot exceeding 0.72 sqm,(size & shape, shade and pattern as approved by GE), as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, over & including M&L 15 mm thick screed bed in cement mortar 1:4, complete all as specified and directed. 55 All as per item No. 54.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed. 56 M&L Machine cut kota stone slab 17 to 20mm thick as in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L 15mm thick screed bed in CM 1:6, complete all as specified and as directed. 57 All as per item No. 56.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed. 58 Taking down cement plaster in any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed. 59 M&L for 15 mm thick rendering in CM 1:4on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface fair and even without using extra cement, complete all as specified and as directed. 60 M&L for 15 mm thick rendering in CM 1:6on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement, complete all as specified and as directed. 61 M&L for 10 mm thick Rendering in CM 1:3 on fair faces of brick work or conc surfaces as in ceilings/chajja/facia & finished even & smooth w/o using extra cement, complete all as specified and as directed. 62 M&L for Preparation ofnew plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed. 63 All as per item No. 62.00 here-in-above, but as on wall surfaces 64 Complete removal of existing treatment of any description on walls and applying with 2 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over & including M&L single coat of primer on walls complete all as specified and as directed. 65 Taking up or down 15mm bore steel tubing medium grade and connections, as in walls, ceiling, floor etc including cleaning for re-fixing or credit to the work 66 All as per item No. 65.00 here-in-above, but20 mm bore 67 Supplying and laying of CPVC pipes, 20 mm ouetr dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laidin trenches or ceiling or fixed to wallcomplete all as specified. 68 All as per item No. 67.00 here-in-above, but25 mm outer dia 69 S&F in replacement bib cock with wall flange, chromium plated brass, fancy type15mm dia complete all as specified and as directed. 70 S&F in replacement over head Shower rose 125 mm diaof ABS Body chromium plated brassbody (Nickel 10 microns and chrome 0.3 microns) with grey face plate & with arm having swivel jointcromium plated best quality, complete all as specified and directed. 71 S&F in replacement angle cock with wall flange, chromium plated brass, fancy type15mm dia complete all as specified and as directed. 72 S&F in replacement PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed. 73 S&F in replacementvitreous ware wash down water closet [Pedestal Pattern], white [ETWC]including plastic water closet seat back soft closed pattern with flat bottom and cover & jet and mild steel chromium plated or aluminium hinging device and P or S trap connecting to drain pipe and flushing pipe etc., complete all as specified and directed. 74 S & F in replacement white vitreous china squatting pan Orissa pattern of size 580 mm X 440 mmwith integral foot rests and PVC P or S trap, including M&L brackets, flush HDPE pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts , includingprovision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed. 75 S&F in replacement 10 ltrs capacity PVC valve less(Super special colors), (ISI Marked) syphonic action type, flushing cistern, low level, with Anti Bacterial Knob, with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and, cistern colour shall be match WC colour, complete all as specified and as directed. 76 S & F 75mm bore PVC [SWR] Floor Trap with grating including jointing to waste pipe fixed with solvent cement, and making floor good ,complete all as specified and as directed 77 S&F in replacementfancy type 600mmx450mm plain edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. 78 S&F in replacementWash basins, Vitreous China white, flat back, size 630x450mm excluding tap, waste chain and plugsbut including brackets(flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe 79 S&F in replacement Pillar taps, fancy type Cast copper alloy, with capstan heads chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15mm bore pipe 80 S&F in replacement vitreous china bowl urinal flat back, size of 465 x 355 x265 mm white (minimum ),with grating and union for discharge pipe (excluding flushing cistern and flush pipe and waste pipe ) in repairs. 81 S&F in replacement PVC waste pipefor WHB/Urinal complete all as specified and as directed. 82 S&F in replacement rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) white, hoisted and fixed in position all as directed of capacity 500 ltrs a Including 20mm bore brass ball valve high pressure with polythene float complete including taking down existing damage water tank all as directed. 83 All as per item No. 82.00 here-in-above, but 1000 ltrs tank capacity 84 S&F in replacement CP mild steel grating 100mm dia complete all as specified and as directed. 85 S&F tubular towel rail 20mm dia brass chromium plated `D type 60cm long with bracket and fixed complete all as directed 86 Dismantling of cast iron of CI / PVC soil, waste & vent pipe jointed in cement mortor of size 110/100mm bore, incld. All fittings, completeall as directed 87 All as per item No. 86.00 here-in-above, but 75mm bore pipe. 88 Supply & laying 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laidin wall/ceiling/floor of suitable size complete all as specified and as directed . 89 All as per item No. 88.00 here-in-above, but 110mm bore pipe. 90 S&F in replacement decorative type curtain rod stainless steel finishofpipe 22 to 25 mm diawith best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end (as approved by GE), complete all as specified and as directed. 91 Dismantling plain or corrugated asbestos sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and as directed . 92 M&L Prepainted Galvalume Aluminium Zinc Coating GI based corrugated Steel Sheet 0.5mm thick of anycolour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed. 93 M & L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including M&L single coat of pink primer complete all as specified and as directed. 94 M&L preparation of new or previously untreatedsteel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over& including M&L singlecoat of red- oxide, zinc chrome primer complete all as specified and as directed. 95 Demolition of stone / boulder masonry walling, built in cement mortarincluding all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed. 96 M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed. 97 All as per item No. 96.00 here-in-above, but except stone 98 Extra over stone walling for hammer dressingto face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed. 99 M&L precast cement concrete block masonry using PCC 1:3:6, type C-1 solid blocks, 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed. 100 Racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed. 101 M&L keyed pointing in cement mortar (1:3) to squared rubble masonryregular coursedor un coursed complete all as specified & directed. 102 M&L for preparation of old painted surfaces of walls or roofs by brooming down or steel wire brushing, scraping down smoke spot, moulds, moss and efflorescent salt and greasy spots and applying two coats of cement base paint, complete all as specified and directed 103 M& L for precast cement concrete Type B-0 1:2:4 (12.50mm graded aggregate) as inlouvres and jallies, cement grill any type model ofZafri , 35mmthick (measured solid), setin cement mortar 1:4 fixedwith PCC post, incld. all mouldings complete all as specified and directed. 104 Supply & laying of precast cementconcrete1:3:6, type C-0 (by using 12.5mm graded stone aggregate) as in pillars (size 100 x 100 mm and 750mm height) toprovide support of RCC jallies, jointed with neat cement slurry, in CM 1:6, and including demolition of existing jallies and removed from MOD land, complete all as specified and as directed. 105 Dismantling of RCC/MS Angle fencing post or struts of any description/section including taking out embeded ,barbed wire in concrete and making good disturbed, complete all as specified and as directed. 106 Dismantling of fencing wire mesh, any type and any size complete all as specified and as directed. 107 Excavating in post holes (of similar holes) each n. Exc. 0.50 cum getting out in any type of soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified and directed. 108 S&F mild steel sections like angle, flat etc in post and struts in fencing including cutting top to shape as directed,drilling holes,notching for wire etc;flat iron fillets (for securing wire mesh etc including all necessary drilling,bolting or riviting etc confirming to Fe-290Gde E-165 complete all as specified and as directed. 109 S&F mild steel screw bolts(machine made) with hexagonal or square heads at one end and scrfewed the other, each screwed end to be fitted with washeres and one haxagonal or square nut not exceeding 5cm long with daia of neck 5 to 11 mm complete all as specified and directed. 110 Supply only chain link MS galvanised fencing of any description, complete all as specified and as directed. Note:- BOO will consitute by GE to determinate the weight of chainlink. 111 Fixing only Chain link fencing including line wires,any mesh, size and type to any standards,rails straining bolts, etc. including provision of binding wire complete all as specified and as directed. 112 Supply only Mild steel round or square bars 10mm dia.,in available length Fe-290 (Gde-165) for fixing of chain link fencingcomplete all as specified and as directed. 113 S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed.Note : - Each line wire to be measured. 114 S & F in repair Fibre glass reinforced translucent 2 mm thick corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and as directed. 115 Complete removal of existing treatment of any description on walls and applying two coats of exterior acrylic emulsion (one or more tints) over & including M&L single coat of primer on walls complete all as specified and as directed. 116 M&L for 18 to 20 mm thick (telephone black shade) granite stone, as in WHB counter top, machine cut, (table rubbed and polished) best quality as per sample, over & including 15 mm thick screeding in CM1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitabledia hole in the slab for the gas pipe, complete all as specified and as directed. 117 M&L Hardcore of gauge not exceeding 63 mm of brokenstone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, compacting with power roller, complete all as specified and as directed. 118 M&L 75 mm thick PCC 1:3:6type C1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & smooth without using extra cement & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval,complete all as specified and directed. 119 M&L Machine cut kota stone slab 20 to 25mm thick as in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L 15mm thick screed bed in CM 1:6, complete all as specified and as directed. 120 M&Lfor 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed. 121 M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns hooking ends cutting bending and binding with mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and as directed. 122 S&F mild steel TMT bar6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed. 123 M&L RCC nominal mix type B-1 (1:2:4) using 20 mm graded stone aggregate as in slab supported on wall, beam and column in floors, roofs, landing, balconies, canopies, ramp roof slab, chajjaand in shelveetc complete all as specified and directed. 124 M&L for sand filling under floors or in foundations including watering and consolidation, spreading and levelling in layers n.exc. 25cm thick and well ramming including watering as rerquired etc, complete all as specified and directed. 125 M&L for 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, drain cover stones, templates, etc, n exc. 2m in length, machine cut on all faces and along exposed edges, self faced on both side and set and pointed in lime mortar 1:3 or cement mortar 1:4,complete all as specified and as directed 126 Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket,ceiling rose etc complete all as specified and as directed 127 M&L for Point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC (FRLS)insulated unsheathed cable confirming to IS-694,1100 Volts grade( ISI Marked), class V in concealed PVC conduit (ISI Marked) not less than 20 mm dia heavy duty with accessories etc and including sunken pressed steel terminal boxes in wall, including 1.50 sq mm PVC insulated unsheathed stranded copper conductor(FRLS) cable for common earth and connecting to earth dolly, suitable for One light/fan/bell point controlled by one, one wayswitchcomplete all as specified and directed. 128 All as per Sr. item No. 127. 00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amps on same board 129 All as per Sr. item No. 127.00 here-in-above, but suitable forOne socket outlet 3 pin 5/6 Amp on independent board 130 All as per Sr. item No. 127.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable(FRLS) including 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLS) for common earth wire for 6 pin 16 Amp socket outlet on independent board . 131 M&L for Point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC (FRLS)insulated unsheathed cable confirming to IS-694,1100 Volts grade( ISI Marked) passing inPVC cassing-N-capping 25/32 mm width fixed on surface of wall/roof/ceiling withexisting/new sunken pressed steel terminal boxesincluding3.00 mmthick plastic laminated sheet top cover and 1.50 sq mm PVC insulated unsheathed stranded copper conductor(FRLS) cable for common earth and connecting to earth dolly, suitable for One light/fan/bell point controlled by one, one wayswitchcomplete all as specified and directed. 132 All as per Sr. item No. 131. 00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amps on same board 133 All as per Sr. item No. 131.00 here-in-above, but suitable forOne socket outlet 3 pin 5/6 Amp on independent board 134 All as per Sr. item No. 131.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable(FRLS) including 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLS) for common earth wire for 6 pin 16 Amp socket outlet on independent board . 135 M & L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring,drawn through in and includingnon-metalicPVC concealed (including Cutting Chases and make good the distrubed surfaces as per existing finishes) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, suitable for One light/fan/bell point controlled by one, one wayswitch, complete all as specified and directed.Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates 136 All as per Sr. item No. 135. 00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amps on same board 137 All as per Sr. item No. 135.00 here-in-above, but suitable forOne socket outlet 3 pin 5/6 Amp on independent board 138 All as per Sr. item No. 135.00 here-in-above, but with using 2.5 Sq mm (nominal area) cable for one 3 pin 16 amp socket on independent board incluing one 2.5 sqmm copper conductor multi standard green colour PVC insulated unsheathed cable 1100 volts grade as earth wire upto common earth & connected to earth dolly complete complete all as specified & directed. 139 S&F switch piano, flush type, single pole, one way, 5/6 Amps, 230 Volts complete all as specified and as directed. 140 S&F switch piano, flush type, single pole, one way, 16 Amps, 230 Volts complete all as specified and as directed. 141 Supply and fix socket out let flush type 6 amp 3 pin suitable for 6 Amp plug top 230 V complete all as specified & directed. 142 Supply and fix socket out let flush type 3/6 pin suitable for 16 Amp plug top multipurpose 230 V, complete all as specified & directed. 143 Supply and fixingin replacement ceiling rose 3 terminals complete incl taking down all as specified and directed. 144 Supply and fixingin replacement lamp holder insulated body with back plate batten/angle type for batten fittings incl taking down old unserviceable holder complete all as specified and directed. 145 Supply and fix fan regulator electronic switch/ socket type completeall as specified and directed. 146 Taking down and refixing of ceiling fan after servicing (cleaning, oiling and greasing) andconnecting up including provision of cable from ceiling rose,complete all asspecified and as directed . 147 Taking down and refixing of exhaust fan after servicing (cleaning, oiling and greasing) andconnecting up including provision of cable from ceiling rose,complete all asspecified and as directed . 148 S&F in replacement sheet metal enclosures 240 voltwith suitable rated bus bar for double doorIP-43 DBs of approved geauge suitable for one MCB SPN as incoming and 6 MCB SP as out going SPN 8 way complete all as specified and directed by Engr-in-charge. 149 S&F in replacement sheet metal enclosures 240 voltwith suitable rated bus bar for double doorIP-43 DBs suitable for one MCB SPN as incoming and 10 MCB SP as out going SPN 12 way completeincl dismentaling of unservceable DB all as specified and directed by Engr-in-charge. 150 S&F in replacement sheet metal enclosures 415 voltTPN 4 way double doorIP-43 DBs suitable for one TPN/ isolator 4 pole MCBas incoming and three TPN MCB as outgoing complete all as specified and directed by Engr-in-charge. 151 Supply and Fix in replacementMCBSingle poleB series5-32 Amps ISI marked incl dismantaling old unserviceable MCB SP . 152 Supply and Fixin replacement MCBSingle pole & neutral B series upto 40 Amps ISI marked incl dismantaling old unserviceable MCB SPN 153 Supply and Fixin replacement MCBSingle pole & neutral B series upto 63. Amps ISI marked incl dismantaling old unserviceable MCB SPN 154 Supply and fixing in replacementMCB TPN B Curve63 to 100 Amps Make incl disntaling of old unserviceable TPN MCB 155 Supply and fixing LED lights fitting 1x 20W, 220V, Cool White, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 156 S&F in replacement LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. 157 Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable, complete all as specified & directed. 158 S&F aluminium strip25 x 3.15 mm with saddles and fixing screws etc for roof conductors and down conductors above groung complete all as specified and as directed 159 M&L submain wiring with two runs of 4 sqmm with one run of 4 Sqmm earth wire of 1100V grade FRLSHPVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through in and including PVC conduit fixed on surface ISI marked and conduit accessaries fixed on surface of wall, ceiling etc and making good and including M&L 15mm dia non mettalic PVC rigid conduit with wall thickness not less than 1.8 mm,and connected to common earth dollycomplete all as specified and directed.Note :- Two runs of 4 sqmm and one runs of 4 sqmm (earth wire) including one run of PVC conduit shall be measured as one length for the purpose of measurement. 160 M&L submain wiring with two runs of 4 sqmm with one run of 4 Sqmm earth wire of 1100V grade FRLSHPVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through and including cutting chasing in wall for concealed using machine cutting and making good and including M&L 15mm dia non mettalic PVC rigid conduit with wall thickness not less than 1.8 mm,accessories concealed on wall / ceiling with PVC saddles and cadmium plated steel screws and connected to common earth dollycomplete all as specified and directed.Note :- Two runs of 4 sqmm and one runs of 4 sqmm (earth wire) including one run of PVC conduit shall be measured as one length for the purpose of measurement. 161 S&F streetLight bracket made out of medium grade GI pipe (as per samplefor 25 mm bore or more suitable for bldg security light fitting) bent to shape including GIclamps nut, bolts, washers, reducer of required size for suitable any type fittings etc complete including necessary painting complete all as specified and as directed. 162 M&L for earthing complete with galvanized steel earth plate electrode of size60cm x 60cm x 6mm thick burried directly in ground vertically at a depth not less than 2.25 metredeep below normal ground level with top edge of the plate not lessthan1.5 metre below normal groundlevel surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt, filling in alternate layer and electrode connections by using galvanized iron earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers made of galvanized iron or steel and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board, and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1: 2: 4 type C2 including excavation and earth work, disposal of surplus soil to a distance not exc. 50 mtr all as specified and as shown on Plate No 5 of SSR Part I (1991)incl dismanteling of existing unserviceable earth pitall as specified and directed by Engr-in-Charge.

Key Value

Document Fees
INR 500 /-
EMD
INR 90000.0 /-
Tender Value
Refer document

Attachment

FileName File Description File Size
Click here to download tender document Tender Documents 0 KB
Click here to download tender document Tender Documents 0 KB
Click here to download tender document Tender Documents 0 KB
Click here to download tender document Tender Documents 0 KB
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail