Estimate for renovation and beautification of Shani Mandir Park in M.C Sonipat -- 1 -Analysis of rate for providing and fixing of concertina coil fencing GI Wire having 2.50 mm wire diameter , 600 mm coil diameter and two horizontal line of concertina GI wire , including the cost of making hole in the angle to pass the Concertina coil through angle and cost of metal clip. 2 Repairing of old play equipment : Chain Swing , Bridge Ladder , Slide Ladder and Sea Saw including rubbing , painting and spraying with good finish by painting machine at site complete in all respect to full satisfaction of Engineer-in-chief. 3 Air Walker: Providing, designing and fixing of Air-Walker of size 100 x 550 x 1480mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thickmade up of hot rolled tubular steel and hot dipped galvanized,and powder coated 80-120 micron thick usingAkzo Nobel or equivalent in desired shade and colour. All welding joints of pipeshall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing.Base plate cover shall be made up of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness U V resistant and colour as approved by Engineer-in Charge. High quality grip rubber should be used on handles. Foothold shall be made ofNylon alloywith rounded edge to prevent impact and injury. Maintenance free bearing should be used in equipment manufactured by reputed companyduly sealed and self lubricated to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters . The equipment should be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. 4 Sit Up Station: Providing, designing and fixing of double sit-up station of size 1500 x 1150 x 650 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thickall pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipeshall be robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and Base plate cover shall be made up of virgin LLDPE plastic by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. The equipment should be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and when concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing of equipment etc. 5 Air Swing: Providing, designing and fixing ofairs winging pair of size 1150 x900 x1250 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and Base plate cover shall be made up of virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearing used shall be maintained free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fittedwithin built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base coverplate and fixing of equipment etc 6 Leg Press: Providing, designing and fixing ofstair stepper in a combination of pair and a single step ofsize 2000 X 550 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing.Handle bars are to be provided with high quality grip rubber at top end. Padalsshall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to bemade from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base coverplate and fixing of equipment etc. 7 Arm Wheel :- Providing, designing and fixing Arm Wheel in a pair ofsize 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing.Handle bars are to be provided with high quality grip rubber.Padalsshall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to bemade from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base coverplate and fixing of equipment etc 8 Elliptical Exerciser :- Providing, designing and fixing Elliptical Exerciserofsize 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padalsshall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to bemade from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base coverplate and fixing of equipment etc 9 Double Cross Walker :- Providing, designing and fixing Double Cross Walker ofsize 1600 X 600 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padalsshall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to bemade from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base coverplate and fixing of equipment etc 10 Seated Chest Press :- Providing, designing and fixing Seated Chest Press ofPullpair ofsize 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized,and powder coated usingAkzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber.Padalsshall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to bemade from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful andU V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shapedwelded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base coverplate and fixing of equipment etc 11 Providing and Fixing Multi Play Activity equipment Covering Area: 27’L x 13’W FRP Wave Slide 6mm thick at 5’H – 2set. FRP Square Canopy 2mm thick -2set FRP Fancy Railing Monkey and Frog shape-4set. FRP Platform 3’.5 x 3’.5 x 5mm thick-2set. M.S Walking Bridge 6’Long -1set. M.S Safety railing – 2set. M.S Climbing Ladder-2set. M.S Wave Climbing Ladder 8’Long-1set. M.S Sea-Saw (Double) 7’long having 4no FRP Sitting seat of 3mm thick With jerk proof system using 4no semi tyres- 1set. M.S vertical station of m.s pipe 2”.5 x 12Gauge ISI Mark-2set. Complete item priming and Painting in P.U Paints and fitting at site complete in all respect engineer in the charge.
