Providing And Supplying Furniture At Flat No.3/5 Suruchi Building, G.J. Bhosale Marg, Mumbai.-1 . Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc. complete. 2 . Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete 3 . Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. 4 . Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. 5 . Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete. 6 . Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete. 7 . Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. complete 8 . Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 kg/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years guarantee on requisite stamp paper including curing etc. complete. 9 . Removing loose rust from the reinforcement bars by wire brushing, light hammering etc. and applying sulphate and chloride free inorganic single component rust remover Rusticide as approved by Engineer in charge conforming to IS 9077. The rusted surface shall become blackish non rusted colour. After 24 hours of application of rust remover, loose particles shall be removed by brush. Apply one more coat of Rusticide. Apply bonding coat slurry of high performance acrylic polymer - Methyl 2-methylpropenoate copolymer with another enoate as approved by Engineer in charge on entire surface. Mix 1 Kg of acrylic polymer with 0.5 Kg of cement. Finish it with ready to use repair polymer modified mortar based on special cements, aldehyde based polymers with thixotropy modifying agents as approved by Engineer in charge (The Polymer Modified Mortar (PMM) should attain min. compressive strength of 20 N/mm2 in 1 day and 30 N/mm2 in 7 days) by adding 13 - 16% water by weight of polymer modified mortar for treatment to the damaged RCC members. Add 1 Kg of Migrating Corrosion Inhibiting Admixture as approved by Engineer in charge per 25 Kg bag of polymer modified mortar. After mixing polymer modified mortar, it can be trowel applied or sprayed. When applying by hand, polymer modified mortar must be forced tightly into the substrate to ensure complete contact with the substrate. (If scaffolding is required, same shall be provided and will be paid under relevant item) (Upto 15 mm thickness at a time). 10 . Removing loose rust from the reinforcement bars by wire brushing, light hammering etc. and applying sulphate and chloride free inorganic single component rust remover Rusticide as approved by Engineer in charge conforming to IS 9077. The rusted surface shall become blackish non rusted colour. After 24 hours of application of rust remover, loose particles shall be removed by brush. Apply one more coat of Rusticide. Apply bonding coat slurry of high performance acrylic polymer - Methyl 2-methylpropenoate copolymer with another innovate as approved by Engineer in charge on entire surface. Mix 1 Kg of acrylic polymer with 0.5 Kg of cement. Finish it with ready to use repair polymer modified mortar based on special cements, formaldehyde based polymer with thixotropy modifying agents as approved by Engineer in charge (The Polymer Modified Mortar (PMM) should attain min. compressive strength of 20 N/mm2 in 1 day and 30 N/mm2 in 7 days) by adding 13 - 16% water by weight of polymer modified mortar for treatment to the damaged RCC members. Add 1 Kg of Migrating Corrosion Inhibiting Admixture as approved by Engineer in charge per 25 Kg bag of polymer modified mortar. After mixing polymer modified mortar, it can be trowel applied or sprayed. When applying by hand, polymer modified mortar must be forced tightly into the substrate to ensure complete contact with the substrate. (If scaffolding is required, same shall be provided and will be paid under relevant item) (15-30 mm thickness at a time). 11 . Providing internal cement plaster 6 mm thick in a single coat using Ready to use wall plaster in cement mortar 1:3 to concrete surface in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. With Prior Approval of Concerned S.E. 12 . Providing internal / external 12 mm thick Ready Mix plaster confirming to IS:4031(Part-4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete. 13 . Providing internal / external 20 mm thick Ready Mix plaster confirming to IS:4031(Part-4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete 14 . Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) 15 . Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. 16 . Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. 17 . Providing and laying telephone black / Amba White / Cadbury brown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc.complete. 18 . Providing 25 mm to 30 mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. a) One side polish 19 . Doors : Providing and fixing full height door shutter at required location having height more than 1.5m made by using soild core commercial type flush doors 35 mm thick of requisite manufacture equivalent with formica laminate sheet finished lamination pattern with or without grooves externally with necessary (BTC) moulding, antitermite treatment to plywood and wood work including all leads and lifts complete as per Architects Drawing and instruction of Engineer in-charge etc. complete 20 . Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. 21 . Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineer in-charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box 22 . Providing and fixing in position Colour anodized aluminium openable window of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick clear float glass etc. complete. 23 . Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. 24 . Providing and fixing in position aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening such as 5 mm thick clear float glass etc. complete. Note : While arriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered. (a) Colour Anodized 25 . Providing and fixing Wall Mounted European type white glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the outside face of wall 10 liter enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps ,20 mm dia. UPVC overflow pipe ,mosquito proof couplings G.I. chain and pulley, with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete.( prior approval of sample and brand by Ex. Engineer is necessary before use) 26 . Providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval typa wash basin model no 3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 m x 0.60 m ) 27 . Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete. 28 . Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nut etc. complete. 29 . Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. 30 . Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. 31 . Providing and fixing 15 mm diameter PVC Aqua kraft type of approved make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete 32 . Providing and applying priming coat on concrete/ masonry/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete. 33 . Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. Applying Asian / Berger / Nerolac / Dulux Paints or equivalent wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hours After applying Asian / Berger / Nerolac Dulux Paints or equivalent acrylic wall putty with appropriate proportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45 % or 65 to 70 % by roller. (With prior approval of S.E.) 34 . Providing and fixing on site wall panelling made by using C.P.T.W.framing out of 38x25mm (unfinished size) at approximately 600x450 mm center to center or as per site conditions and covered by 6mm and moulding by 19mm thk marine ply of the requisite manufacture generally confirming to IS 303/IS 10-1980 finished with 1.5 mm laminated with grooves pattern of approved quality including all necessary & moulding,moulding pattern, & melamine polish. Antitermite treatment to plywood and wood work with 10 years guaranteed bond etc.including all lead and lifts etc.complete as per architects drawing and istruction of engineer incharge. 35 . Storage Full Height : Providing and fixing 53cm deep Cupboard type Storage Unit made out of 19mm thick marine plywood of the requisite manufacture generally confirming to I.S. 710-1980 for frames, internal verticals horizontal divisions, shutters and 6mm & 12mm thick marine plywood for drawers with locks,handles, hardware, lipping & beading patti (BTC) etc. The shall be finished with veneer in approved pattern with grooves etc. and two coats of french polish and melamine polish for all BTC moulding& lipping patties with antitermite treatment to plywood & wood work with ten years guarantee on requisite stamp paper including all leads & lifts etc. complete as per drawing and instruction of Engineer-in-charge etc. complete. 36 . Low Height Storage - Providing & fixing on site 40 cm Deep Low Height Storage Unit at require location less than 1.35 meter height by using 19mm marine ply of requisite manufacture generally confirming to I.S. 303/IS. 710-1980 for frame, internal verticals, horizontal divisions, openable shutters, 6mm thick marine ply back, with necessary locks, handles, hardware, lipping (BTC), moulding etc. The total shall be finished with formica laminate sheet finished lamination pattern with grooves externally and two coats of french polish with anti-termite treatemtn to plywood & wood work including all leads & lifts etc. complete, as per Architects Drawing and instruction of Engineer in Charge. 37 . Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT. 38 . Providing & Arrangemnt of MId Back, Normal Syncro Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5prong/Nylon Base with Leather Upholstery 39 . Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (kgs): 66 (Kg) Seating Capacity: Five Seat 40 . Tables (1.20X0.60) : Providing & fixing in position table for the Clerical Staff having overall size of 120x60x76 cm height made out of 19mm thick Marine Ply of the requisite manufacture generally confirming to I.S.303/I.S.710-1980 top, vertical side & 6mm marine plywood of requisite manufacture generally confirming to sides and 6mm marine ply bottom with necessary sliders one open shelf of 19mm thick marine ply with necessary lipping on external sides and foot rest out of 40x75 mm (finished dimension) CPTW etc. as per drawing and instructions.the external side and top shall be finished with 1mm thick laminate matt/suede/fine line finished lamination pattern with grooves all internal surfaces on table and drawer shall be internally finished with two coats of french polish with antitermite treatment. 41 . Providing and Fixing Dining table of Overall S.S (IS 6911:1992),gradeof steel 304, Thickness of the table is 40 mmStructure top to be Of s.s 18 SWG 304,Grit. Under Structure to be Vertical poles of 50 mm Dia (16 gauge 304 grade) and top and Bottomsupporting frame Structure to be 50 x 50 mm Square tube etc. complete. Glide shall be of Plastic fixed at the under structure to prevent the damage of table top during stacking. Legs shall be of SS and 38 mm dia (16 gauge 304 grades). pipe legs are fixed with under structure and table top etc. complete. 42 . Providing and fixing SS (IS 6911:1992) grade of steel 304 Dinning chirsfor dining Hall and dining Room area as per the drawing or approvedsize and shape including all lead lift shiftingto work location etc. complete. 43 . Providing and supplying wooden sofa made with minimum 19mm.Marine ply (IS 710 : 2010) structure and internal frame work made of C.P. teak / Maranti wood seat made with minimum 19mm.Marine ply (IS 710 : 2010) and cushion madewith foam of 150mm thick - 32 density on seat covered with 14mm thick - 18 density foam. Back made with wooden frame of minimum 50mm X 40mm with 4 mm. ply and coveredwith foam of 100mm thick - 32 densities covered with 14mm thick - 18 density foam for back extra support to the shape all foam of seat and back covered with tapestry approved by E-I-Charge. (Basic rate Rs. 450/- metre.) Handle made with wooden frame with box of 12mm. ply covered with 14mm thick - 18 density foam with tapestry etc.complete. 44 . Providing and supplying wooden sofa made with minimum 19mm.Marine ply (IS 710 : 2010) structure and internal frame work made of C.P. teak / Maranti wood seat made with minimum 19mm. Marine ply (IS 710 : 2010) and cushion madewith foam of 150mm thick - 32 density on seat covered with 14mm thick - 18 density foam. Back made with wooden frame of minimum 50mm X 40mm with 4 mm. ply and coveredwith foam of 100mm thick - 32 densities covered with 14mm thick - 18 density foam for back extra support to the shape all foam of seat and back covered with tapestry approved by E-I-Charge. (Basic rate Rs. 450/- metre.) Handle made with wooden frame with box of 12mm. ply covered with 14mm thick - 18 density foam with tapestry etc.complete. 45 . Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2 mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT. Side Panel: - The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The overall width of the side panel is 150mm. The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure. Head Board :- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 650mm. Foot Board :- The foot board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 450mm. Bed Base: - The Bed Base is made up of 12mm thick Prelam Particle Board with both side White laminate. 46 . Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mm X 750mm X 450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc. 47 . Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400LX 400DX 415H The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding 48 . Dressing Table @400LX 400DX 1800H Providing& Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4mm thick pasted on 18mm thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker. 49 . Wardrobe with Mirror @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900LX 600DX 1965H The wardrobe side panels and doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18mm thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36mm prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and 18mm batons on all sides to achieve 36mm overall thickness). The exposed edges of the top are sealed with 2mm thick PVC edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450 (D) made of 18mm thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160mm pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required. 50 . Lowering down the debris obtained from breaking and removing the cement plaster / burnt brick masonry of the first floor by any means without causing dust nuisance and damage to structure, stacking the same as and where directed including cleaning the site complete. 51 . Removing any kind of debris including loading in truck and conveying to dumping point approved by MCGM, unloading, spreading etc. complete. With all leads and lifts. 52 . Basic Test of Cement : Carrying out Standard Consistancy Fineness, Specific Gravity, Setting Time (Initial &Final ), Compressive Strength, Soundness Test 53 . FINE AGGREGATES : Carrying out test of Fineness Modulus (Sieve Analysis), Silt & Clay Content 54 . ALUMINIUM SECTION : Carrying out test of Thickness, Mass Per Running meter 55 . PLYWOOD : Carrying out test of Determination of Resistance to dry heat, Determination of Moisture Content, Determination of Density, Thickness of Plywood, 56 . WOOD : Carrying out test of Density, Moisture Content. 57 . FLOORING TILES (MOSSAIC / CEMENT) : Carrying out test of Flooring of Natural Stone (Kota, Marble, Granite, Tandur etc.) Water Absorption , Specific Gravity 58 . CERAMIC TILES / VITRIFIED TILES : Carrying out test of Water Absorption, Modules of Rapture (Set of 6 Tiles) 59 . MORTAR : Carrying out test of Compressive Strength. (Set of 3 Cubes) 60 . Royalty Charges for Other Minerals are to be paid to the contractor after producing receipt of royalty paid to the Govt. for the material used for this work.
