Tender For Supply, Installation And Commissioning Of Devices, Machineries, Equipment And Tools, Etc. In Laboratories And Workshop Of Electrical Engineering Department Of Jangipur Government Polytechnic, raghunathganj-West Bengal

Supply, Installation And Commissioning Of Devices, Machineries, Equipment And Tools, Etc. In Laboratories And Workshop Of Electrical Engineering Department Of Jangipur Government Polytechnic- 1 Profometer Rebar Diameter & Cover Meter 2 Half Cell Meter 3 Cannon Manning cum Cannon Fenske Viscometer bath with Vacuum Pump 4 Pile Integrity Tester 5 Hand Operated Soil Sample Extruder 6 Standard Penetration Test Apparatus 7 Turbidity Meter 8 Multiparameter pH/ORP/EC/TDS/Salinity/DO/Pressure/ Temperature Waterproof Meter, 10m cable 9 Multiparameter Photometer with COD for Water and Wastewater 10 Bacteriological Incubator 11 Laminar air flow with UV Lamp 12 Universal Water bath 13 MacConkey Broth: NutriSelect Plus, 14 Gutzeit Apparatus (Glass) 15 Desiccator 16 Digital PH meter 17 Digital Conductivity meter 18 Digital colorimeter 19 Digital DO-meter 20 Complete set for Thin Layer Chromatography 21 Arsenic set (For Laboratory) 22 Digital Thermometer or Normal Thermometer 23 Daniel -Cell for EMF measurement 24 Set up to determine and verify the time period of oscillation of a cantilever 25 Set up to convert a galvanometer into an ammeter. 26 Kit to verify Kirchhoff’s law using electrical circuits 27 Instrument set up to Test the performance of speaker 28 Instrument set up to study the internal layout of black and white TV receiver. 29 Instrument set up to: - a)Study the internal layoutof colour television, b)Fault finding in given Colour TV :i) No colour ii) Red b)Colour only iii) Blue colour only iv) Green colour only v)Magenta colour only vi)Cyan colour only vii)Yellow only viii)No raster, No Sound. c) Measure voltage level to sketch composite video signal at different stages of TV receiver. 30 Instrument set up to find the maximum range of a RADAR (using simulation software) 31 Instrument set up to Built-in LED state control by push button sketch implementation (Arduino) 5 Built-in LED blinking sketch implementation (Arduino) 6 Built-in LED blinking by toggling states based on binary operation (Arduino) 7 Controlling multiple LEDs with a loop and an array (Arduino) 8 Use a potentiometer to control the blinking of an LED (Arduino) 9 Temperature monitor using LCD display and LM35 (using Adrino ) 32 Instrument set up tostudydrain and transfer characteristics ofFET 33 Instrument set up tostudy drain and transfer characteristics of JFET 34 Instrument set up tostudy the input and output characteristics and to determine the h-parameters of a BJT for : — (a) C-E configuration, (b) C-B configuration, (c) C-C configuration 35 Instrument set up to determine frequency response characteristics of RC coupled amplifier circuit and calculation of bandwidth, midband gain, input impedance and output impedance for : (a) Single-stage amplifier, (b) Double-stage amplifier 36 Instrument set up to study the rectifier with and without capacitor filter for : — (a) Half-wave rectifier, (b) Full-wave rectifier 37 Instrument set up to study the operation of Oscillators (any two) using OPAMP - a) Hartley, b) Colpitt, c) Wein-bridge, d) Phase Shift, e) Crystal 38 Instrument set up to study the operation of Voltage to Frequency converter 39 Instrument set up to study the operation of Oscillators (any two) using OPAMP - a) Hartley, b) Colpitt, c) Wein-bridge, d) Phase Shift, e) Crystal 40 Instrument set up to study the applications of op amp IC 741 as a) clipper b)clamper c)Schmitt trigger d)voltage follower 41 Instrument set up for Measurement of strain/force with the help of strain gauge load cell 42 Instrument set up for Measurement of displacement with the help of LVDT. 43 Speed Control of DC Shunt motor(both Armature voltage & flux control included) 44 3phase Delta manufactored Variable voltage & variable Frequency Drive(VFD) 45 Dynamic braking of three phase squirrel cage induction motor using contactor control. 46 Analog tachometer 47 Use dual trace oscilloscope to determine AC voltage & current response in given R,L,C circuit 48 Use variable frequency supply to create resonance in given series and parallel R-L-C circuit or by using variable reactor or variable capacitor 49 Perform experiment to measure thermal performance of a solar water heating system. 50 Allen Bradley Micrologix 1400 PLC with software

Refer document

INR 25000.0 /-

Refer document

FileName	File Description	File Size
Click here to download tender document	Tender Documents-1	0 KB
Click here to download tender document	Tender Documents-1	0 KB
Click here to download tender document	Tender Documents-1	0 KB
Click here to download tender document	Tender Documents-1	0 KB
Click here to download tender document	Tender Documents-1	0 KB
Click here to download tender document	Tender Documents	0 KB