Tender For Special Repair To Guest House At Bus Station Azamgarh. - Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.DSR 15.7.4 In cement mortar 2 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :15.12.1 Of area bryond 3 sq. Metres. 3 Same as in item 1 but for lime terracing SI 696 4 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within50 metres lead as per direction of Engineer - in- charge. DSR 15.7.3 5 Brick work with common burnt clay (non modular) bricks of designation 7.5in super structre above plinnth level up tofloor V level in cement mortar1:4 (1 cement :4 coarse sand) . (SI 6.4.1) 6 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.3 7 Centering and shuttering including strutting, propping etc. and removal of form for DSR 5.9.5 Lintels, beams, plinth beams, girders, bressumers andcantilevers 8 Centering and shuttering including strutting, propping etc. and removal of form forDSR 5.9.3 Suspended floors, roofs, landings, balconies and accessplatform 9 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.DSR 5.22.1 Mild steel and Medium Tensile steel bars 10 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.DSR 15.56 11 12 mm cement plaster DSR 13.4.1, 1:4 (1 cement : 4 coarse sand) 12 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding. 13 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete DSR 13.80 14 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.DSR 13.83.2 Two coats 15 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : DSR 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 16 Finishing walls with Premium acrylic smooth exterior paint with silicon additives of required shade New work (two or more coats applied @1.43Lite/10Sqm over and including base coat of water proofing cement paint applied@2.2 Kg/10 sqm). DSR13.47.1 17 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. DSR 11.41.2 size of 600 x 600 mm. 18 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. DSR 11.56.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown,Cat Eye or equivalent. 19 Supply and fixing of anodized Aluminium work for partition door or sliding window with standerd builtup tublar section having 1.5 mm. thick Aluminium section of approved make ISI mark 20 micron Anodizing fixed with fast nut,rowel plug screws. 20 Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-incharge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). DSR 21.50 21 Providing and fixingfirst quwality CeramicGlazed tilesmm or more (thickness to be specified by the manufacturer),conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:3 (1 Cement : 3 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.DSR 11.37 A 22 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.18.8.2 20 mm nominal outer dia Pipes 23 Providing and fixing white vitreous china single bodd water closet (European type W.C. pan) with ISI marked white solid plastic seat and lidetc complte DSR 17.3.1 24 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer DSR 17.7A 25 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.DSR 17.38.2.1 26 Providing & fixing viterous china toilet paper holder.DSR 17.34.1 27 Providing & fixing 15 mm nominal bore CP brass bib cockof approved quality conformingtoIS 8931.DSR 17.49.1 28 Providing and fixing 15 mm nominal bore C.P brass long nose bib cock of approved qualityconforming to IS standardsandweighing notlessthan 810 gms. DSR18.50.1 29 Providing & fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points of approved quality conformingto IS8931.DSR 18.53.1 30 S/F of 110 mm dia PVC pipe6 kg per sqm appd brand ISI. 31 Sal .wood wrought framwd and fixed etc complete. SI 403 32 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35mm thick including ISI marked Stainless Steel butt hinges with necessary screw. DSR 20.1.35 33 Approximate cost of Aluminum Fitting with screws for door and window including hinges.PWD 472 (1) 34 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.DSR 16.91.2 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. 35 Disposal of malwa beyond municipal limit incluiding loading,catage and unloading complete .DSR 1.1.3 36 W/P for light with 1.5 sqmm. FRPVC insulated multistrand single core copper conductor cablein PVC conduit pipe in wallcomplete with 1.5 Sqmm FRPVC insulated multistrand single core copper conductor cable as earth wire drawn in side the conduit, PWD 138 (C) 37 Same as in item 1 but for fan point. PWD 140 (C) 38 Same as in item 1 but for plugpoint. PWD 141 (C) 39 Supply & fixing of power plug with 20A/250 volts flush type switch and 5 pin 20 A/250 volts flush type universal modular socket on concealed MS box including supply of all material, labour T&P etc. required for proper completion of the work. PWD 1139 A 40 S/F of sheet steel enclosure surface / flush mounting fitted with 20 amp 2 pin and earth metal clad scraping earth plug and socket complete. (for AC etc) PWD 1031 Cat-B 41 Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gaugePVCcoduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting, including matching colour wash etc complete in all respects. (a)2 x 4 sq. mm. with 1 no 14 SWG copper earth continuity wire, in 20 mm dia conduit.PWD 221 (C) 42 Supply fixing and concealing PVC conduit pipe in the wall including cutting of brick work, laying of conduit and fixing it with M.S. hooks and then plastering with cement, sand motar finished to the level, with matching color wash including cost of proper threading of the conduit and providing necessary sockets, bends and chuck nuts as directed by the engineer-in-charge with supply of all material labour and T&Prequired for proper completion of work. (for Telephone / Television / circuits)(a) 20 mm dia. conduit (2.0 mm) thick PWD 148 A 43 (b) 25 mm dia. conduit(2.0mm)thick PWD 149 A 44 S/F of surface / flush mounting SPN Distribution board without MCB complete in all respects as directed at site by Engineer-in-charge. 4 Ways Cat A PWD 1022 45 Supply & fixingof 6/10/16/20/25/32 amp. SP MCB (10 KA) Kat B PWD 1002 46 S/F of 25 Amp DP MCB (10 KA) Kat A PWD 1009 47 S/F of 25 amp FP MCB(10 KA) Kat A PWD 1019 48 Supply Fixing and making commection of 30 MA E.L.C.B. (Earth leakage circuit breaker) of din/R.C.C.B. railmounting complete in all respects as per directionandsatisfaction of engineer-in-charge.25Amp 2 Pole PWD 392 49 Supply&burryingof 600mm x 600mm x 6.0mm G.I. plate, vertically for earthing with itstop at least 3 meters below ground level complete with 20 mm G.I. pipefor watering funnel, 30 cm square C.I. frame with hinged cover, masonry housing, alternate layersof coke/charcoal and salt at least 150 mm thick alroundetc. complete in all respects.PWD 706 50 Supplying & Layingof 25mm x 3mm. G.I. strip for earthing purpose as required complete in all respects. PWD 716 51 Supply and fixing brass nickle plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connectedwith the earth conductor.10 sqmm 2 core PWD 503.b 52 Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge.10 sq.mm. PWD 504 c 53 S/Foffactorywired, LED Tubelight 1x22 watt& without end covers for 1 no 22 watt LED lamp complete in all respect. PWD 1413 CAT AAA 54 Erection and testing of ceiling fan and regulator etc excluding supply of down rod, complete in all respect.PWD 1115 55 Erection and testing of ceiling fan and regulator for room height upto 3.50 meter including supply of 3 mm thick G.I. Rod 19 mm dia. Duly painted, complete in all respect.PWD 1116 56 Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts nuts and washers etc complete in all respects.PWD 1120 57 Supply & fixing ofFanregulator,dimmer, 300/400 watt, ISI marked, ontheexisting switch board includingmaking connections, required material,labourT/Petc.for proper completionofworkto the satisfaction of Engineer of work. PWD 1203 58 S/Fof shocktreatmentchart ( prescribed under I.E.rules ) duly framed with glass and supported from back with hard board orsoft board with supply of all material labour T & P etc for proper completion of work.PWD 1134 59 Supply of AC230/250 volts, 50 HZceiling fanwith standarddownrod, blades, 2 nos. caps etc.complete (Make : Bajaj / Crompton / Havells) 1200 mm sweep 60 Supply of AC230/250 volts, 50 HZ exhaust fansincluding providingnuts, bolts, mounting frame and other accessories etc.complete (Make : Bajaj / Crompton / Havells)
