Public Service Commission Construction Of New Cabin At 3Rd Floor For Joint Secretary I- 1 Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (B) 15 Micron colour annodizingj) Fixed partitions. (Unsupported length of vertical member more than 1.5 mtr.or both endsof vertical member restrained but panels more than 0.9 sq.m.)k) Movable door shutter.i) Door frame. (Top & sides) 2 ii) Shutter : Top rail. 3 Bottom rail. 4 Lock rail 5 Door vertical 6 Glazing clip. 7 (B) 15 Micron colour annodizingj) Fixed partitions. (Unsupported length of vertical member more than 1.5 mtr.or both endsof vertical member restrained but panels more than 0.9 sq.m.)i) Top , bottom& side member. 8 ii) Intermediate member 9 Glazing clip. 10 Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor(iv) 12mm In 3rd Floor 11 Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge.The rate includes the cost of labour, adhesive and all incidental charges thereof.In ground floor Glossy/Matt/Suede excluding surface texture or metallic lustre. (i) Thickness of laminate 1.5mm (In 3rd Floor 12 Supplying bubble free float glass of approved make and brandconforming to IS: 2835-1987iv) 5mm thick coloured / tinted / smoke glass. 13 Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminiumalloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVCroller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window withfixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge.10-12 Micron thickness Annodizing film Natural white 14 Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units(B) Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. 15 (D) Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all othernecessary arrangements for fixing the partition to walls, floors, beams, columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge. I) For partitions using section of size: b) 101.50mm x 44.45 mm 16 (b) Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick) 17 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. a) One Coat i) Water based interior grade Acrylic Primer 18 Applying Acrylic Emulsion Paint of approved make and brand on wallsm and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) ii) LuxuryQuality 19 (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc 20 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white) 21 (A) Supplying Aluminium casted body hydraulic door closer as per I.S.I. 22 (B) Supplying 125 mm. Dia acrylic handle for aluminium door as per approved make & brand. (a) Natural Colour 23 (D) Supplying Aluminium casted body Butt Hinge (KOBRA type).(Natural white) 24 Supplying 4 lever mortice lock or any approved make and brand as per direction of the Engineer- in -Charge. i) 150 mm 25 Supplying and affixing optically clear polyester sun control window film having acrylic pressure sensitive adhesive on one side & an acrylic abrasion resistant coating on the other, with composition of infrared absorbing carbon & free from any optical defect. The film characteristics should conform to ASTM E308, ASTM E903, ASTM E84 and ASHIRAE. The film should be pasted after preparatoryworks without any cracking, delamination, bubbling, discolouring and variation in total transmission of light across the width at anyportion along the length doesnt exceed 2% over the average including scaffolding & relevant others to complete in all respect as per manufacturers specification & direction of Engineer -in-Charge. (Note: This work should not be executed without specific permission of Superintending Engineer)(b) Superior Quality : Film Thickness - 2.0 Mil, Glare Reduction >75%, U factor < 1.03, Emissivity < 0.70 26 Sub Total 27 GST 18% 28 CESS 1%
