Bids Are invited for iNTERIOR DESIGN AND BUILD FOR THE NDMA AT IIPA BHAWAN, IIPA CAMPUS, NEW DELHI. -CONCRETE WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) Cum 5 TOTAL CARRIED OVER TO SUMMARY MASONRY WORK , DRY WALL PARTITION & WALL PANELLING Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level 2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 109.344 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 3 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 30.92805 4 Providing and fixing of 115mm thick Drywall system (tested for fire rating of 120 mins, Estimated STC -52 (+/-3) ) This includes fixing of Floor & Ceiling Channel (0.55 mm thick, 92mm wide & having two flanges of 30mm each) to the Floor and Slab with 8mm Dia 40mm long Anchor Fasteners @ 600 mm c/c. ULTRAFRAME™ Wall Studs (0.55 mm thick, 90 mm wide having one flange of 34mm another of 36 mm) are placed at 610mm centers in Floor and Ceiling channel. profiles are rolled with G.I Steel (120 GSM & 230 Mpa Yield Strength) conforming to as per IS 277. Provide 99x2500x0.9mm thick Fixing Channel behind Horizontal Board Joints with the help of 4.2x13mm wafer head metal to metal screws. 1x12.5mm thick Standard Plasterboard (Conforming to IS 2095 & BSEN 520) ISI & EPD Certified Gypsum Board is screw fixed with Metal Framing with the help of 25mm long Drywall screws at 300 mm centres. The screw fixing of gypsum boards to the metal framing at the periphery, openings and cut edges should be at 150mm centres. All the boards must be staggered All joints to be taped & finished with 50mm wide USG Knauf Paper tape & APJC Jointing compound. Design Criteria: Height at site – 3.5 meters , STC -43, Fire Rating – NA All joints to be taped & finished with 50mm wide Paper tape & redimix APJC Jointing compound confirming to ASTM C475. All Openings cut outs & periphery shall be treated with appropriate sealant. Appropriate Cavity Toggles to be used for any unplanned loading in the Drywall and to be installed as per manufacturers recommendation. All work should be carried out as per the recommendation of Engineer Incharge and as per recommended practices of the manufacturer. All overlaps in the metal studs required for extension to achieve the wall height shall be boxed for minimum length of 300mm and no horizontal joints of the boards should coincide with the overlap. All Openings cut outs & periphery shall be treated with Fire & Acoustical sealant. The drywall should withstand lateral wind pressure of 200 Pa with deflections limited to L(Span)/240 criteria. Sqm 782.65935 Cladding Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick 5 Granite of any colour and shade Sqm 7.24 MARBLE & GRANITE WORK Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. completeat all levels. Granite stone slab colour black, Cherry/Ruby red 6 Area of slab above. 0.50 sqm Sqm 6.87 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge. 7 Granite work Metre 11.45 8 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. Metre 11.45 9 Extra for providing opening of required size & shape for wash basins / kitchens sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. Each opening 5 10 Fabric stretched Acoustic wall panelling system: Providing and fixing of Acoustic wall Fabric panel system using PVC Grippers to Stretch the Fabric (Approved Colour & Pattern of Fabric with density of Less than 300 GSM ) as per ASTM E 84 & thermal conductivity 0.034w/mk with desired acoustic management 0.80 NRC. The G.I frame ( Base Frame after soundproof membrane ) of thickness 0.50 consist of GI metal stud frame of size 50mm having one flange of 41mm and other of 44mm placed @ every 600 mm c/c in vertical direction. The MICRONE ( for Sound Insulation - Acoustical Property ) of thickness 50mm and density 40Kg/m3 is fixed in between studs enact with chicken mess ( Purpose to hold the MICRONE to its place firmly ) .On outer side one layer of 12 mm perforated WPC BOARD ( Water Proof with High Density Board with Acoustical & Soundproofing Properties ) is screwed. Screw fixing is done mechanically. WPC boards Perforation ( Holes to trap the sound within to eliminate ECHO 100% ) to be done at site according to technical Specification of Proposed AV Systems & Equipments . A layer of 1/2 thick Dycrone (Synthetic wool to filter the sound - hard to soft ) is fixed on the perforated WPC baord to give cushioning to the pannels and fabric is streched Through PVC Grippers as per design chosen or proposed by Designer / Architecht or selected by customer of its own Sqm 254.35125 11 Providing & fixing Sliding folding partition 3.2 height in extruded aluminium sections with Bottom/ top track and with sound insulation value of > 50 dB and shutter with laminate finish with all fitting fixtures and supporting framework work, etc., complete Sqm 52.76775 Wood-paneling 12 Providing and fixing of 12mm ply on wall surface with required packing for leveling, ply is finished in laminate of approved shade and make. Further it is cladded with pine wood battens of size 40mm x 20mm, fixed with gap of 60mm. Battens are finished in melamine polish as per approved sample. Complete as per decoration plan and as specified & directed by Interior Designer. (Surface Area of the paneling shall be measured for billing) Sqm 270 13 FLUTED PANEL WORK ON WALL - Providing and fixing 12mm thick MDF Fluted Panel on wall/ partition and plywood faced with 12MM Thk finish with paint as per approved shade etc. all complete. Sqm 240 WOOD & PVC WORK Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). 14 Second class teak wood Cum 0.854565 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 15 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm 36.75 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 16 Frame size 50 x 100 mm Rmt 4.95 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 17 35 mm thick Sqm 1.575 18 Acoustical & Soundproof Door - ( New Chokhat & Door to be made with double PATTAM to block the sound from both end - internally & externally ) - Size 8x4 - double layer with soundproof membrane - with filled rockwool within the gap - double - HDHMR Board and Mica Finish from Externally at both End In and out (18mm HDMHMR Board - GAP of 2 - 18mm board as finished - Total Debth would be 5 ) Sqm 7.56 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : 19 Decorative veneer facings of approved manufacture Sqm 200 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete. 20 50 x 20 mm Rm 84.7 21 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Each 54 22 Providing and fixing SS tower bolts, ISI marked, with necessary screws etc. complete as per the approved make : Each 21 23 Providing and fixing SS 304 sliding door bolts, ISI marked with nuts and screws etc. complete as per approved make : Each 3 24 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. Each 15 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 25 125 mm each 42 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 26 Twin rubber stopper each 21 27 Providing & Fixing of frameless Glass partition with Glass door consisting of 12mm clear toughened glass and fixing with single leg spider, ceiling/bottom to glass connector, glass to glass connector, handle, doorset, floor spring, pivot etc, all the necessary fittings upto all height including scaffolding all complete as shown in attached drawing and as per the direction of Engineer-in-charge Sqm 187.13385 28 Providing and fixing Toilet cubical(of following standard dimension which includes 600mm door size width) made up of thermosetting resign treated high pressure ,self supporting decorative compact laminates with permanently incorporate anti-bacterial agents(under JIS Z2801:2000 certification) during manufacturing .Compact board should be resistance to water immersion through permissible increase on thickness and mass <0.60% and board density >1.35kg/cm3 and fulfilled the criteria of green guard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. each 2 29 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. sqm 1.2375 Granite Stone of approved shade FLOORING WORK Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost f nosing of steps etc. complete. 30 40 mm thick with 20 mm nominal size stone aggregate sqm 713.5 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 31 40 mm wide and 4 mm thick Rm 1284.3 32 Wood Work for Stage 450 mm height sqm 27.5 33 Providing and laying joint less 3-4 min thick epoxy flooring to achieve perfect 0-0 level without any undulations on existing mosaic/kota stone flooring after surface preparation by grinding/rubbing & cleaning the base floor, followed by epoxy primer on prepared surface followed by epoxy screed on primed surface followed by epoxy putty over screed and finally epoxy SL top, having materials of approved manufacture certified by Council of Scientific & Industrial Research (CFTRI) . Selfsmooth glossy finish, all as per manufactures specifications inclusive of necessary curing, finishing and carrying all related operations for proper completion of work. (Make- MRF/FOBROCK/DR. FIXIT/CIPI or equivalent make. complete in all respect as per approved colour. Sqm 37.6976 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 34 25 mm thick sqm 37.6976 35 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. sqm 6.01 36 Synthetic carpet flooring of high grade duly edged with broad high quality wooden beadings, L shaped beading on steps coated with radium paint / strip, floor mounted LED light with row indicator. Providing and laying woven woolen carpet/synthetic wool . Carpet shall be machine tufted loop pile carpet. Pile content 100% polypropylene. Yarn quality shall be tricolor imported yarn. Total pile weight shall be 500 gm(+-5%) and Effective pile height shall be 3.00 mm(+-5%) so that complete carpet would be 5.00 mm. carpet weight 1000gm/sqmt.+-5% of approved sample, and shade. Carpet should be easily cleanable by vacuum cleaner and occasionally dry cleaned. Carpet edges should not fray upon cutting. Carpet shall be fixed on 12mm thick rubberized coir under layer fixed on floor with rubberized adhesive, ends of the carpet shall be secured in position with floor by providing necessary wooden beading fixed to floor with necessary adhesives. sqm 713.5 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with 37 38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete. sqm 238.1 38 Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineerin-Charge. Sqm 166.45 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size 39 Size of Tile 600x600 mm Sqm 7.93 40 Size of Tile 600 x 1200 mm Sqm 320.7 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). 41 Size of Tile 600x600 mm Sqm 25.872 Grouting the joints of flooring/wall tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /grouting and finishing complete as per direction of Engineer-in-charge. 42 Size of Tile 600x600 mm Sqm 339.63 ROOFING WORK Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : 43 GI Metal Ceiling Clip in plain Beveled edge global white colour tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. Sqm 11 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 44 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. Sqm 37.6976 45 Providing and fixing Designer Wooden ceiling make / fabricated out of 8/12 mm thick plywood , duly covered with 1.0 mm thick laminate and making grooves in the desired pattern, and duly screwed to GI ceiling sections also incorporating 2 x 2 soft wood sections where ever specified as drawing. The work includes edge bending from all sides and filling the grooves with matching colour paint / polish etc complete as reqd.. The payment area will be the visible area only Sqm 478.0753333 Water Proofing Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. 46 IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). Sqm 13.75 FINISHING WORK 47 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Sqm 512.065 48 Providing , spraying and applying Texture paint as per approved shade as per approval of the architect. Bi colour texture paint will be used. On POP finish wall to give a smooth surface as per approval of the Architect.( optional for pillar) Sqm 860.83895 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 49 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) Sqm 10 Aluminium work 50 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). Sqm 7.56 51 Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge Nos 4 DISMANTLING AND DEMOLISHING Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 52 In cement mortar Cum 5 53 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Cum 2 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 54 With cement mortar 1:4 (1cement: 4 coarse sand) Total Quantity : 22965
