|
| 1 | Items : |
| 2 | Surface dressing n exc 15 cm deep, including removing shrubs, vegetation, grass, bush , weed, trees and saplings, undergrowth, roots, and trees not exceeding 30cm grith (measured one metre above ground level), in hard/ dense soil. As directed by EIC. |
| 3 | Excavating in trenchesin hard/ dense soil,n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out. As directed by EIC. |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.hard/ dense soil. As directed by EIC. |
| 5 | Plain cement concrete 1:4:8 (40 mm graded aggregate) in foundation, filling and mass concrete. M&L. As directed by EIC. |
| 6 | Reinforced cement concrete (design mix M-20) with 20mm graded aggregates in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete. M&L. As directed by EIC. |
| 7 | Reinforced cement concrete (design mix M-20) with 20mm graded aggregates in Columns, pillars, piers, posts and struts M&L. As directed by EIC. |
| 8 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, (Rough finished flat surfaces of concrete).M&L. As directed by EIC. |
| 9 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions, (Fair finished finished square, rectangular or polygonalsurfaces of concrete).M&L. As directed by EIC. |
| 10 | Formwork to cornices and mouldings of any shape in cross section and of any girth, (Fair finished finishedsurfaces of concrete).M&L. As directed by EIC. |
| 11 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. M&L. As directed by EIC. |
| 12 | Mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. M&L. As directed by EIC. |
| 13 | Rendering 10mm thick, in cement plaster 1:4on fair faces of brick work or concrete surfaces and finished even and smooth (without using extra lime or cement). M&L.As directed by EIC. |
| 14 | Preparation of new concrete surfaces of any description, over 10cm in width or grith, not otherwise described, priming with priming paint plaster coat and painting with two coats of Synthetic enamel yellow paint. M&L. As directed by EIC. [Make of paint: Asian, J&N, Nerolac, Berger, Dulux as informed by DOO (C&S)] |
| 15 | Painting Labels, etc, n exc 0.1 sq. m each, including cutting in edges with Synthetic Black enamel paint. M&L. As directed by EIC. [Make of paint: Asian, J&N, Nerolac, Berger, Dulux as informed by DOO (C&S)] |
| 16 | Writing letters or figures (Block, Roman, Italic or Indian) in 5CM height, n exc. 30 cm. M&L. |
