tender for civil work Tahsil Someshwar Vikash Khand Takula Gram Kakrad Ra U Ni Syetra Manila 1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, for all lift, including getting out the excavated soil and disposalof surplus excavated soil as directed, within a lead of 50 m. 2 Providing and laying in position cement concrete1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived fromnatural sources : 8 graded stone aggregate 40 mm nominalsize derived from natural sources) 3 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and1:2:4 (1 cement : 2 coarse sand (zone-lll) derived fromnatural sources : 4 graded stone aggregatereinforcement - All work up to plinth level : 4 Reinforced cement concrete1:1.5:3 work in beams suspended floor roof etc. 5 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete 6 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers 7 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts 8 reinforcement for R.C.C. work including straightening, cutting,bending, placing in position Mild steel and Medium Tensile steel bars Thermo-Mechanically Treated bars of grade Fe-500D or more. 9 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 10 Honey - comb Brick Work 10/11.4 cm thick with common burnt clay bricks of class designation 7.5 in supper structure above plinth level upto floorV level with cement mortar 1:4 11 Providing and fixing 25 mm thick shutters for cup board etc. :Second class teak wood including ISImarked anodized aluminium butt hinges with necessary screws 12 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part 1) non-decorative type, core of block board construction30 mm thick including ISI marked Stainless Steel butt hinges with necessary screwswith frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 13 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 14 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete.11.3.1 40 mm thick with 20 mm nominal size stone aggregate 15 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 16 12 mm cement plaster of mix : 1:4 (1 cement:4 fine sand)finished with floating coat of neat cement 17 Neat cement punng 18 Distempering with 1st quality acrylic distemper (ready mixed) having VOCcontent less than 50 gram/litre, of approved manufacturer and of requiredshade and colour all complete to achieve even shade and colour : 19 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 20 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :painting wood work with Deluxe Multi Surface paint 21 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 22 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 23 Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.15 mm dia nominal bore 24 Providing and fixingG.I. Union in existing G.I. pipe line, cutting andthreading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required 15 mm nominal bore wherever required : 25 Providing and fixing 15 C.P. brass bib cock of approved quality conformingto IS:8931 :15mm nominal bore 26 Providing and fixingC.P. brass stop cock (concealed) of standarddesign and of approved make conforming to IS:8931.15mm nominal bore. 27 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 28 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed 1.00 mm thick with zinc coating not less than 275 gm/m² 29 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, for all lift, including getting out the excavated soil and disposalof surplus excavated soil as directed, within a lead of 50 m. 30 Providing and laying in position cement concrete1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived fromnatural sources : 8 graded stone aggregate 40 mm nominalsize derived from natural sources) 31 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and1:2:4 (1 cement : 2 coarse sand (zone-lll) derived fromnatural sources : 4 graded stone aggregatereinforcement - All work up to plinth level : 32 Reinforced cement concrete1:1.5:3 work in beams suspended floor roof etc. 33 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete 34 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers 35 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts 36 reinforcement for R.C.C. work including straightening, cutting,bending, placing in position Mild steel and Medium Tensile steel bars Thermo-Mechanically Treated bars of grade Fe-500D or more. 37 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 38 Honey - comb Brick Work 10/11.4 cm thick with common burnt clay bricks of class designation 7.5 in supper structure above plinth level upto floorV level with cement mortar 1:4 39 Providing and fixing 25 mm thick shutters for cup board etc. :Second class teak wood including ISImarked anodized aluminium butt hinges with necessary screws 40 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part 1) non-decorative type, core of block board construction30 mm thick including ISI marked Stainless Steel butt hinges with necessary screwswith frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 41 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 42 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete.11.3.1 40 mm thick with 20 mm nominal size stone aggregate 43 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 44 12 mm cement plaster of mix : 1:4 (1 cement:4 fine sand)finished with floating coat of neat cement 45 Neat cement punng 46 Distempering with 1st quality acrylic distemper (ready mixed) having VOCcontent less than 50 gram/litre, of approved manufacturer and of requiredshade and colour all complete to achieve even shade and colour : 47 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :painting wood work with Deluxe Multi Surface paint 49 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 50 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 51 Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.15 mm dia nominal bore 52 Providing and fixingG.I. Union in existing G.I. pipe line, cutting andthreading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required 15 mm nominal bore wherever required : 53 Providing and fixing 15 C.P. brass bib cock of approved quality conformingto IS:8931 :15mm nominal bore 54 Providing and fixingC.P. brass stop cock (concealed) of standarddesign and of approved make conforming to IS:8931.15mm nominal bore. 55 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 56 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed 1.00 mm thick with zinc coating not less than 275 gm/m² 57 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, for all lift, including getting out the excavated soil and disposalof surplus excavated soil as directed, within a lead of 50 m. 58 Providing and laying in position cement concrete1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived fromnatural sources : 8 graded stone aggregate 40 mm nominalsize derived from natural sources) 59 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and1:2:4 (1 cement : 2 coarse sand (zone-lll) derived fromnatural sources : 4 graded stone aggregatereinforcement - All work up to plinth level : 60 Reinforced cement concrete1:1.5:3 work in beams suspended floor roof etc. 61 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete 62 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers 63 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts 64 reinforcement for R.C.C. work including straightening, cutting,bending, placing in position Mild steel and Medium Tensile steel bars Thermo-Mechanically Treated bars of grade Fe-500D or more. 65 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 66 Providing and fixing 25 mm thick shutters for cup board etc. :Second class teak wood including ISImarked anodized aluminium butt hinges with necessary screws 67 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part 1) non-decorative type, core of block board construction30 mm thick including ISI marked Stainless Steel butt hinges with necessary screwswith frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 68 Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 69 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete.11.3.1 40 mm thick with 20 mm nominal size stone aggregate 70 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 71 Neat cement punng 72 Distempering with 1st quality acrylic distemper (ready mixed) having VOCcontent less than 50 gram/litre, of approved manufacturer and of requiredshade and colour all complete to achieve even shade and colour : 73 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :painting wood work with Deluxe Multi Surface paint 74 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 75 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 76 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed 1.00 mm thick with zinc coating not less than 275 gm/m² 77 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, for all lift, including getting out the excavated soil and disposalof surplus excavated soil as directed, within a lead of 50 m. 78 Providing and laying in position cement concrete1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived fromnatural sources : 8 graded stone aggregate 40 mm nominalsize derived from natural sources) 79 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and1:2:4 (1 cement : 2 coarse sand (zone-lll) derived fromnatural sources : 4 graded stone aggregatereinforcement - All work up to plinth level : 80 Reinforced cement concrete1:1.5:3 work in beams suspended floor roof etc. 81 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete 82 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers 83 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts 84 reinforcement for R.C.C. work including straightening, cutting,bending, placing in position Mild steel and Medium Tensile steel bars Thermo-Mechanically Treated bars of grade Fe-500D or more. 85 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 86 Brick work with F.P.S brick of class designation 75 in super structure above plinth cement mortar Cement mortar 1:6 (1 cement : 6 coarse sand) 87 Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in superstructure above plinth level up to floorV level.Cement mortar 1:4 (1 cement :4 coarse sand) 88 Providing and fixing 25 mm thick shutters for cup board etc. :Second class teak wood including ISImarked anodized aluminium butt hinges with necessary screws 89 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part 1) non-decorative type, core of block board construction30 mm thick including ISI marked Stainless Steel butt hinges with necessary screwswith frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 90 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 91 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete.11.3.1 40 mm thick with 20 mm nominal size stone aggregate 92 Providing and fixing Ist quality ceramic glazed wall tiles conforming to1S: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of anysize as approved by Engineer-in-Charge, in skirting, risers of steps anddados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarsesand) and jointing with grey cement slurry @ 3.3kg per sqm, includingpointing in white cement mixed with pigment of matching shade complete. 93 Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08% andconforming to IS: 15622, of approved make, in all colours and shades,laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointingwith grey cement slurry @ 3.3 kg/ sqm including grouting the joints withwhite cement and matching pigments etc., complete.Size of Tile 500x500 mm 94 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 95 12 mm cement plaster of mix : 1:4 (1 cement:4 fine sand)finished with floating coat of neat cement 96 Neat cement punng 97 Distempering with 1st quality acrylic distemper (ready mixed) having VOCcontent less than 50 gram/litre, of approved manufacturer and of requiredshade and colour all complete to achieve even shade and colour : 98 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 99 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :painting wood work with Deluxe Multi Surface paint 100 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 101 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps 102 Providing and fixing white vitreous china water closet squatting pan (Indiantype)Orissa pattern W.C. pan of size 580x440 mm 103 Providing and fixing controlled flush, low level cistern made of vitreouschina with all fittings complete.10 litre (full flush) capacity-white 104 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 105 Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.15 mm dia nominal bore 106 Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc.20mm dia nominal bore 107 Providing and fixingG.I. Union in existing G.I. pipe line, cutting andthreading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required 15 mm nominal bore wherever required : 108 Providing and fixing 15 C.P. brass bib cock of approved quality conformingto IS:8931 :15mm nominal bore 109 Providing and fixingC.P. brass stop cock (concealed) of standarddesign and of approved make conforming to IS:8931.15mm nominal bore. 110 Providing and fixing soil, waste and vent pipes :Sand cast iron S&S pipe as per 1S: 1729 111 Providing and filling the joints with spun yarn, cement slurry and cementmortar 1:2 (1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :100 mm dia pipe 112 Providing and fixing M.S. holder-bat clamps of approved design to Sand Castiron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes andmaking good the walls etc.For 100 mm dia pipe 113 Providing and fixing soil, waste and vent pipes Centrifugally cast (spun) iron socket & spigot(S&S) pipe as per IS: 3989 114 Providing and filling the joints with spun yarn, cement slurry and cementmortar 1:2 (1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 75 mm dia pipe 115 Providing and fixing M.S. holder-bat clamps of approved design to SandCastiron/cast iron (spun) pipe embedded in and including cement concreteblocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size), including cost of cutting holes andmaking good the walls etc. :For 75 mm dia pipe 116 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I.surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation,foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coatof neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of classdesignation 7.5 117 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 118 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed 1.00 mm thick with zinc coating not less than 275 gm/m² 119 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, for all lift, including getting out the excavated soil and disposalof surplus excavated soil as directed, within a lead of 50 m. 120 Providing and laying in position cement concrete1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived fromnatural sources : 8 graded stone aggregate 40 mm nominalsize derived from natural sources) 121 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and1:2:4 (1 cement : 2 coarse sand (zone-lll) derived fromnatural sources : 4 graded stone aggregatereinforcement - All work up to plinth level : 122 Reinforced cement concrete1:1.5:3 work in beams suspended floor roof etc. 123 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete 124 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers 125 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts 126 reinforcement for R.C.C. work including straightening, cutting,bending, placing in position Mild steel and Medium Tensile steel bars Thermo-Mechanically Treated bars of grade Fe-500D or more. 127 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) 128 Providing and fixing 25 mm thick shutters for cup board etc. :Second class teak wood including ISImarked anodized aluminium butt hinges with necessary screws 129 Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part 1) non-decorative type, core of block board construction30 mm thick including ISI marked Stainless Steel butt hinges with necessary screwswith frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 130 Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 131 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete.11.3.1 40 mm thick with 20 mm nominal size stone aggregate 132 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 133 Neat cement punng 134 Distempering with 1st quality acrylic distemper (ready mixed) having VOCcontent less than 50 gram/litre, of approved manufacturer and of requiredshade and colour all complete to achieve even shade and colour : 135 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) 136 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :painting wood work with Deluxe Multi Surface paint 137 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 138 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 139 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed 1.00 mm thick with zinc coating not less than 275 gm/m² 140 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. asrequired. 141 Supplying and fixing of following sizes of steel conduit alongwith accessories in surface/recess including painting in case ofsurface conduit, or cutting the wall and making good the samein case of recessed conduit as required.3 pin 5/6 A socket outlet 142 Supplying and drawing following sizes of FRLS PVC insulatedcopper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.5/6 amps switch 143 Supplying and fixing metal box of 150mm X 75mm X 60mmdeep (nominal size) on surface or in recess with suitable size ofphenolic laminated sheet cover in front including providing andfixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,connections, painting etc. as required 144 Supplying and fixing following piano type switch/ socket on theexisting switch box/ cover including connections etc. as 2 way 5/6 A switch 145 Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 146 Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired.2 X 4 sq. mm + 1 X 4 sq. mm earth wire 147 Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired.2 X 6 sq. mm + 1 X 6 sq. mm earth wire 148 Supplying and fixing metal box of 180mm X 100mm X 60mmdeep (nominal size) on surface or in recess with suitable size ofphenolic laminated sheet cover in front including providing andfixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano typeswitch, connections, painting etc. as required 149 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of2.7 metre long etc. with charcoal/ coke and salt as required. 150 Supplying and laying 6 SWG G.I. wire at 0.50 metre belowground level for conductor earth electrode, includingconnection/ termination with GI thimble etc. as required. 151 Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator)12 way , Double door 152 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, Ccurve, miniature circuit breaker suitable for inductive load offollowing poles in the existing MCB DB complete withconnections, testing and commissioning etc. as required. Single pole. 153 Supplying and fixing following rating, double pole, 240 V,isolator in the existing MCB DB complete with connections,testing and commissioning etc. as required.63 A 154 Supplying and fixing brass batten/ angle holder includingconnection etc. as required. 155 Supplying and fixing 3 pin, 5 A ceiling rose on the existingjunction box/ wooden block including connections etc. asrequired. 156 Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required.
