Limited Tender For Furnishing Work Of Kasbe Digraj Branch => Limited; A NEW WORK AS PER UBI NORMS 1 Armstrong false ceiling: - Providing and fixing in position false ceiling in Armstrong 600 x 600mm x 15/16 mm Dune supreme RH99 Prima tile with Tegular edge frame work as specified by Armstrong Co. with suspenders wherever required. Making necessary framework for A.C. ducting if any and necessary cutouts for diffusers and light fitting, taping and finishing to proper line & level including making grooves and trap doors for A.C. unit in 18mm thick M.R. grade plywood with stainless steel hinges & locks with molding 1” x 1” for edges including finishing with white plastic Emulsion Paint etc. complete in all respects. ( Note:- Only the plan area will be measured for payment No. extra payment will be made for cutouts, grooves, moldings etc.) 456.00 Sqft. 2 False ceiling- Gypsum board:- Providing and fixing in position false ceiling in Gypsum board sheet 12mm thk with GI frame work with suspenders wherever required. Making necessary framework for A.C. ducting if any and necessary cutouts for diffusers and light fitting, taping and finishing to proper line & level including making grooves and trap doors for A.C. unit in 18mm thick M.R. grade plywood with stainless steel hinges & locks with molding 1” x 1” for edges including finishing with white Luster Paint etc. complete in all respects. ( Note:- Only the plan area will be measured for payment No. extra payment will be made for cutouts, grooves, moldings etc 611.63 Sqft. 3 Banking counter :- Providing & fixing in position Front office counter 2’6” wide as per dwg comprising of the following comp. in all respects :- i). Working top made with 19mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1 ¼ ” x 1” T.W. molding finished with melamine polish. Inside edge will be provided with ½ “ x 1” T.W. beading Patti with melamine finish. ii). Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades. iii). Vertical drop (horizontal band) shall be provided on the facial below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1mm thick groove shall be provided at the joint of two different shades of laminate. iv). Glazed partition above working top to be provided with 12mm thick clear glass cut to the standard shape fixed to partition as per fixing details and to boxing with concealed S.S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish. v). 3’-10” high boxing (10”x10”) made with 18mm thick plywood finished with 1mm thick laminate including providing and fixing 6mm thick square frosted glass at a height 3’2” above finished floor level. vi). 1’9” high boxing (5”x5”) made with 12mm thick plywood finished with 1mm thick laminate. 27.75 Rft. vii). Vertical supports made with 18mm thick plywood finished with white enamel paint. viii). Telescopic CPU stand/ ready made keyboard tray shall be provided of approved model and make. ix). Foot rest made with T.W. member of size 4”x1 ½ “ finished with French polish. The item to include all necessary hardware and fitting in stainless steel finish, leaping to all edges and making provision only for electrical fitting behind the front. Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beadings with melamine polish for fixing the glass are to be provided. 4 Cash counter: - Providing and fixing in position cash counter 2’6” wide as per drawing comprising of the following:- i). Working top made with 19mm thick plywood finished with 1mm thick laminate. outside edge of the working top shall be provided with 1¼” x 1” T.W. molding finished with melamine polish inside edge will be provided with ½ “ x 1” T.W. beading Patti with melamine polish. ii). Vertical facia (Apron)made with 18mm thick plywood finished with 1mm thk. Laminates of the different shades. iii). Vertical drop (horizontal band) shall be provided on the facia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1mm thick groove shall be provided at the joint of two different shades of laminate. iv). Glazed partition of 1’4” height above working top provided with 12mm thick toughened and frosted glass besides nontransparent film from inside fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing . The exposed edges of the glass shall be finished in mirror polish. v). Transaction top shall be provided with 12mm thick toughened glass (partly glazed partly frosted) fixed horizontally with concealed stainless steel D bracket, Both exposed edges (inside and outside) shall be molded and finished in mirror polish. vi). Glazed partition having height 1’0” above the transaction top (in fascia) shall be provided with 12mm thick glass (clear) with cut out of 8”x4” as per drawing. The edges of cut out and the top edge of glass are to be mirror polished and to be fixed to partition as per fixing details and to boxing with concealed S.S. finished ‘D’ brackets as shown in glass (Clear) above the slit to be fixed to partition as per fixing details and to boxing with concealed S.S. finished ‘D’ brackets as shown in the drawing. The exposed edges shall be finished in mirror polish. viii). 7’7” high boxing (10”x10”) made with 18mm thick plywood as per drawing with 1’6” horizontal extension at the top including providing and fixing 6mm thick square frosted glass at a height of 5”-11” above finished floor level. ix). 1’9” high boxing (5”x5”) made with 12mm thick plywood finished with 1mm thick laminate are to be provided. x). Telescopic CPU stand/ready made keyboard tray shall be provided of approved model and make. xi). Footrest made with T.W. member of size 4”x1½” finished with French polish. xii). Drawer units as per drawing shall be provided and each drawer should have vertical partitions for keeping the currency notes and multipurpose Godrej locks. Facia of drawer unit shall 5.00 RFt be finished with 1mm thk. Laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless steel finish) and channels as per approval of the project consultant/ Bank. xiii). Boxing as per drawing made with 12mm thick plywood finished with synthetic enamel paint shall be provided below the table top for electrical conducing and at the bottom for the LAN cabling/ Telephone wire conducting. The item to include all necessary hardware and fittings in stainless steel finish, leaping to all edges and making provision only for electrical fitting behind the vertical drop and also in the 10”x10” boxing as shown in the drawing Necessary beadings with matching melamine polish for fixing the glass are to be provided as per drawing/as directed. 5 Manager’s table:- Providing & fixing Manager’s table of size 6’0” length 3’0” width with 19 mm plywood for top, side support & key board bottom. 12 mm plywood for drawer, 19 mm plywood for front. Top & drawer front, side finish with 1 mm thk. Laminate. Top must be covered with 12mm glass. Internal surface finish with oil paint foot rest of size 3” x 1 ½” with T.W. section finish with French polish. Telescopic channel fixed to keyboard & other fixtures & lock as suggest by Architect. T.W. leaping 1” X ½” for edges finish with french polish/ oil paint etc. complete. 1.00 No. 6 Officer’s table:- P& F Officer’s table of size 4’0” x 2’.6”- Specification as per above 3 No. 7 Glazed partition for Manager cabin, Store, UPS :- Providing & fixing partition up to ceiling with 2”x1 ½” T.W. section or 19 mm double ply section at 2’.0” c/c/ grid, 6 mm ply on both side as per dwg. finish with 1 mm thk. Laminate & 6/8 mm glass with itching as per design above 3’0” & 1’6” level, glass should fix in B.T.C. beading of size ½” x ½” both side exposed surface should be French polish. Door must be provided with door closer or floor spring with 8mm glass with etching as per design etc. comp. 532.95 Sqft. 8 Glazed Partition for Cash counter cabin : Providing & fixing 7’6” ht. partition with 2’x1 ½” T.W. section or 19 mm double ply section @ 2’.0” x 2’.0” c/c grid & 6 mm plywood for both side finish externally with 1 mm thk. laminate below 3’0” height as per design & above 6mm thk. Glass with itching as per design upto 7’0” height for sides and back. For front side 6mm glass fixed in T.W. beading of size 1” x ½ “finished with French polish or oil paint. All unexposed surface should be french polish or oil paint. Glass must be provided with itching as per design. Door should be provide with fixed in floor spring or door closer of approved quality with lock latch & handle of approved company etc. complete. 76.00 Sqft. 9 Providing and fixing in position anodised extruded aluminum partitions, partly glazed and partly laminated or fully laminated as per drawings having frame made out of extruded tubular section of size 40 mm x 60 mm and bottom member of size 150mm x 44.5mm x 3.00mm thick with12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic 10 Sqft. resin conforming to IS 128231990, laminated on both sides, Nova teak or equivalent and 5 mm thick selected quality plain/ float glass panels fixed with aluminum glass clips 12 mm x 12 mm and rubber cushioning beading to glass partitions as per approved drawing etc. compete with powder coating. 10 3’0 ht. / Low ht. storage cupboard:- 3’0” ht Low height Storage/ Back storage(Credenza) :- Providing and fixing in position full height storage/ Low height storage/ Back storage (credenza) as per design using plywood of 19mm thickness finished with 1mm thick laminates as shown in the drawing and all other sides shall be finished with white enamel paint as detailed there in. The storage units shall be provided with handles ( Stainless steel finish) as per approval of the project consultant/ bank. All exposed plywood surfaces to be finished with 1mm thk laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1”x ¼ ” T.W. leaping. All exposed T.W. section to be melamine and internal surfaces to have white enamel paint as directed. Item to include ply boxing, all necessary hardware and fitting in stainless steel finish, leaping to all edges comp. in all respects. 251.25 Sqft. 11 7’0 ht. / full ht. storage cupboard-: Same as above 96.75 Sqft. 12 ACP Paneling for wall :- Providing and fixing in place aluminum Composite panel cladding of approved quality, shade, colour, make (Euroband / Alucobond etc.)per design, in flat or rounded shapes, perfectly in level / slope, line, and plumb, at all heights, over Aluminum frame and as directed by architects. Panels shall be installed with accessories recommended by the Manufacturer, required hardware, silicon sealent (Dow Corning 789) masking tape, necessary scaffolding etc. complete in all respects. The support structure and aluminum frame shop drawings shall be submitted to the architects for approval before start of work. Aluminum Composite Panels shall meet the following minimum specifications: Panels shall be exterior grade, 4mm thick (0.5mm – 3mm – 0.5mm) composed of Polyethylene Core sandwiched between two sheets of Aluminum of minimum 0.5mm thickness. The outer top skin shall be coated with KYNAR 500 PVdF or similar coating. The panel product shall carry a 10 years Warranty on weather durability, UV color fading, corrosion, chalking, fading, weather damage and manufacturing defects and confirm to ASTM standards. 310.00 Sqft. 13 Waiting S.S. sofa- 3 seat:- Providing SS finish 3 seated sofa as per Architect selection ( All body SS coating & for seat & back SS perforated sheet ) 3.00 No. 14 Writing Desk:- Providing & fixing Writing Desk/ Slip counter with 19mm ply for bottom, wall front, side & internal division for slip with 1 ½ mm thk laminate with 1”x1 ½ leaping finish with oil paint. Top with 10mm glass fix in T.W. 1”X1” section as per design etc. comp. 1.00 No. 15 Flap Door: - Providing & fixing flap door horizontal or Vertical as per shown in drawing with 19mm ply finish with 1.5mm thk. laminate fixed with hinges and tower bolt etc. 1.00 No. 16 Notice Board :- Providing & fixing notice board with 19 mm ply for back side & 12 mm thk. soft board fix in 1” x ¾” T.W. 2.00 No. leaping & cover with cotton cloth approved by consultant etc. Shutter with 6 mm glass fix in aluminum 1”x½” sliding channel with lock. 17 Paint (Luster/plastic Paint ):- Preparation of surface for wall & ceiling with Luster paint with two coat & with one coat of primer & 2 coat of putty with scrubbing & other process etc.. 3640.00 Sqft. 18 Paint (Oil Paint ) :- Preparation of surface with synthetic enamel or oil paint with two coat & with one coat of primer with scrubbing & other process for window grill & window shutters and existing wooden door etc.. 525.00 Sqft. 19 Providing and fixing in position, Single/Double shuttered aluminium extruded powder coated openable door of specified size with aluminium door frame of powder coated section 101.60 x 44.75mm, 3.18mm thick and shutter comprising of powder coated section having bottom and lock rail of size 150mm x 44.5mm x3.00mm thick top rails 47.62 x 44.45mm x 3.00mm thick, vertical style 47.62 x 44.45 mm, 3.00mm thick and for shutter plain glass panes 5mm thick for top panels and 12mm thick both side laminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark , heavy duty, Hydraulic floor spring of 150 Kilogram capacity, having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250mm length aluminium tower bolts, 150mm dia. Pad handle, etc. as per detailed design and drawing or as directed by Architect including all materials, labours, and equipment etc.complete 40.00 SqFt. 20 Providing and fixing of Wall panelling as per design in 8mm thk. Commercial Plywood of approved make and framing in 19mm thk. Plywood (3x1.5”) with 1mm thk. Laminate finished as per approved shade and design including cleaning etc. complete. 100.00 Sqft
