Tender For Portable Toilet For Security At Gate No.01 In The Actrec Campus.; 1 Portable Cabin of size 10x8 with corrugated HR sheet with an internal partition of HR corrugated sheet bisecting at the centre. Double roofing with heat insulation inside the portacabin with two-way slope and additionally MS raised structure provision to be made. Each separation will have two toilet blocks (Dim: 890mm x 840mm x 1980mm per block) with signage indicating Male/Female, which will be made out of HPL sheets of thickness 8mm and all accessories as required.Doors as per the drawing. Providing wash basins along with taps and fittings in each partition of male and female, internal plumbing are to be considered inside the portable cabin scope. An aluminium partition is inside the cabin as per the drawing. Flooring to be supported by MS pipes or angles at 600mm intervals with flooring of Antiskid tiles with waterproofing at the base. Providing and fixing of LED lights, Mirrors, Hooks/Hangers, handwash and Soapholders, exhaust fans in all toilets as well as in changing rooms, wall-mounted fans, and power sockets shall be made., Outside door entry LED lights IP 67 type,Doors and windows are to be provided as per the drawing. 75mm thick glass wool insulation on all sides.Including a 500-litre overhead tank for water supply. Provision of the inlet and outlet of sinks shall be made as per the drawing. Including the supply and fixing of all internal and external UPVC, CPVC, PVC pipes as well as fittings within a 10m radius of the portable cabin. All complete as per the instructions of the Engineer in charge. The provision for painting inside and outside as per the technical specification, windows, silicone sealant, anti-termites and finishing materials is to be considered in this costing. 2 Dry stone rubble soling/pitching of 150 mm to 250mm size shall be approved quality, hard, free from cracks, durable, preferably black trap. Rubble shall be laid on leveled base close to give compact, surface. If base is not properly leveledsame will have to be done without any extra cost. Voids in the joints shall be filled with selected chips. A sample of paving shall be prepared and got approved before proceeding ahead. After stones are laid with thickness of 200mm and packed with chips, sandshall be spread and watered to fill remaining voids. Sandshall be allowed to go into joints till final packing is obtained. Rate quoted shall be for materials, labour, watering, leveling site, before paving, consolidating etc. complete. 3 Providing and laying in position ready mixed M15 grade plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, including the cost of centering, scaffolding, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineerin-charge. 4 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. 5 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.8 mm thick with zinc coating not less than 275 gm/m² with colouring all complete as per the instruction of engineer incharge 6 Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. 7 External Plastering: 20mm thick cement Plaster of mix 1:4 (1 cement: 4 fine sand) on rubble stone masonry as per the instruction of Engineer incharge. 8 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. W.C. pan with ISI marked white solid plastic seat and lid, including providing dual taps and jet spray. This also includes removal of existing W/c 9 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 10 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps 11 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. :25 mm nominal dia Pipes 12 Providing and fixing a brass ball valve with all fixtures as per the instructions of Engineer in charge. - 25mm dia 13 Electrical works 14 Supplying and erecting singlepole andneutraldistribution board(SPNDB), with 2 ways for incoming and8 ways (8 poles)for outgoing SP MCBs,with door, 1.2mm thickness surface/flush mounted, IP 43 Protectionon provided iron/GI frame as per specification no. SW-MCBDB 15 Supplying, erecting & marking DP MCB 6A to 32A, C-serieswith ratedshort - circuitbreaking capacity (Icn)10kA in provided distribution board as per specification no.SW-MCB 16 Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short-circuitbreaking capacity (Icn)10kA in provided distribution board as per specification no.SW-MCB 17 Supplying, erecting& terminatingFR XLPE insulated,galvanisedsteel wire armoured (round) cable 1100 V, 3 core4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 18 Exavation of all kind of soil as per required 900 mm below ground level including blasting & chiseling, using compressor, dewatering, back filling, reinstatement, after work completion, if necessary disposal of excess earth within the radius of500 Mtrs etc, stacking of rocks at selected places as per instruction of EIC.(Composite) 19 25 x3 sqmm GI Strip for earthing
