Tender For Periodical Services And Misc B/R Works In Hq Wac Complex And Areaunder Age B/R-I Of Ge (Af) Subroto Park; 1 Taking down cement of cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge 2 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (Cement plaster 1:4) finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge 3 M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (Cement plaster 1:6) finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge 4 M&L for rendering 5mm thick cement mortar (1:3) as in ceiling, soffit of staircase, chhajjas facia etc including cement slurry etc complete all as specified and as directed by the Engineer-in-Charge. 5 M&L for three coats of white wash on ceiling, soffit of staircase, chhajjas facia etc newly plastered surfaces including preparation of newly plastered surfaces or unplastered surfaces complete all as specified anddirected by the Engineer-in-Charge. 6 M&L for preparing new surfaces (plastered or unplastered) of walls and applying two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls complete all as specified anddirected by the Engineer-in-Charge. 7 M&L for preparation of old painted wooden surface of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified anddirected by the Engineer-in-Charge 8 M&L for one coat of synthetic enamel paint including preparation of old decorated steel surfaces/concrete surfaceof any description over 10 Cm width or girth not otherwise described complete all as specified anddirected by the Engineer-in-Charge 9 M&L waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness1 mm, of Asian Paints or its equivalent over the plastered/old painted wall after scrappingto prepare the surface even and smooth complete and . Sanding of the putty surface with Asian Paints TruCare Wall Sander: L- 01/H-01 or equivalent (having mechanical vacuum mechanism) having RPM not less than 1500, sannding pad of 240 Grit or above having dia of 7/9 to make the surface free from dust etc. by skilled labour as per following steps:-Step 1) Mix the putty powder by adding 40-50% water and mix it with Asian PaintsTrucare Putty mixer(Trucare Putty mixier with min1400 W power havinng mixer rod ofindustrial stell grade 45 with the mixing capacity of min 2.5 kg putty per minute)Step 2)Apply the first coat the prepared mixer with the help fully automatic airless spraymachine of putty application of Asian Paints Trucare Graco Spray Machine(Model: Mark VII) or equivalant having a DC electric motor of 3.3 KW having flow speed of max 6ltrs per minutes with a maximum pressure 230 bar having maximum tip size 0.041Step 3) Allow 6-8 hrs time to dry the putty surface Note:(a) Masking of window/doors during spray painting using polythene film will be included. (b) work will be executed upto 5th floor using MS scaffolding 10 M&L for applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed.Note: -(a)Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application). note; (a) Masking of window/doors during spray painting using polythene film will be included. (b) work will be executed upto 5th floor using MS scaffolding 11 M&L for one coat of acrylic water based exterior grade primer @0.9 ltr(undiluted)/10 sqmtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalent having an electric motor of min. 1 HP of capacity with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent quotes. note; (a)Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application). note; (a) Masking of window/doors during spray painting using polythene film will be included. (b) work will be executed upto 5th floor using MS scaffolding 12 M&L for water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up Resistance of Asian Paints Ltd or its equivalent with low VOC less than 50 , Anti Algal properties in two coats@ 1.79 ltr (undiluted)/ 10 sqm diluted with water in 5:2 ratio applied over priming coat with fully automatic airless spray machine of paint application of Asian Paints TrucareGraco or equivalant having an electric motor of min. 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both thecoats of paint with 8 years performance warranty from Manufacture and instructions complete all as specified and directed.Note; (a) Masking of window/doors during spray painting using polythene film will be included. (b) work will be executed upto 5th floor using MSscaffolding 13 M&L for preparation of new/old plastered surfaces of walls & applying one coat of acrylic water based interior grade primer @ 0.8 ltr(undiluted)/10 sqmtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spraymachine of paint application of Asian Paints Trucare Graco or equivalant having an electric motor of min. 1 HPcapacity with a flow speed of min 1 ltr per minute having a pressure o f3300 PSI.Allow 6-8 hrs to dry the surface for painting of subbsequent quotes.note; (a)Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application). Note : (a) Masking of window/doors during spray painting using polythene film will be included in unit quoted rate. (b) work will be executed upto 5th floorusing MS scaffolding 14 M&L for two coats of smooth interior acrylic emulsion with rich matt finish having VOC less than 50 grams per Ltr complying LEEDS criteria @1 Itr (undiluted) /10 sq mtrs Diluted with water in 2:1 ratio applied over priming coat with fully automatic airless spray Machine of paint application with a flow speed of min 1 Ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint as per manufacturer instructions complete all as specified and directed.Note: (a) Masking of window/doors during spray painting using polythene film will be included in the unit quoted rate. (b) work will be executed upto 5th floor usingMS scaffolding 15 M&L for complete removing existing treatment old surface of wall and applying two coatdistempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturerof required shade and colour, over applying wallcareputty of 2 mm thickness over surface to prepare the surface even and smoothas per manufacturers specification.complete all as specified anddirected by Engineer-in-Charge.Note:- Work will executed upto 5th floor. 16 M&L for preparation of old decorative surfaces including scraping down smoke dust mould, mean cut salt and trading oils and greasy spot etc. on ceiling including cornices, plasters etc. (plastered or unplastered surfaces) and applying one coat of white (lime) wash on old washed surfaces complete all as specified and as directed by Engineer-in-Charge. 17 M&L for10mm thick plaster of Paris ceiling (Gypsum anhydrous) to sunk or raised moulding to flat surface overmetal frame work inclreinforced with G.I. wire mesh & Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre & Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.Note : Unit quoted Rates shall also includestaking down of electrical fitting and refixing the same if required 18 S&F in repair self adesive anti skid srips for stairs of approved width (50mm to 75mm) complete all as specified and directed by Engr-in-Charge. 19 Dismantling plain corrugated steel sheeting any gauage thick ness including Nainital and similar pattern complete all as specifed and directed. 20 S&F for 2mm thick fibre glass reinforced translucent corrugated sheeting withtwo corrugated side lap fixed with L or J type or cranked hook bolts complete all as specifed and directed. 21 S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. 22 S&F in repair for 15mm bore CP autometic/touchless power sensor oprated wash hand basin tap screwed down for iron pipe and fixed with power battery complete all as specified and directed by Engr-in-Charge. 23 S&F plain or coloured floor mounted bathroom vanity of size upto 600mm to 900mm in width and 800mm to 900mm in height of water proof prelaminated PVC material with fixed wash hand basin along with suitable pillar tab and water disposal arrangment, with required drawers and shutters complete all as specified and directed by Engr-in-Charge.Note :- Unit quoted Rate shall alsoincludes hinges, handles, locks, magnetic catch, sliding channels. 24 M&L for removing plants/shrubs grown on wall/junctions with roots duly rendering herbicidechemical and making good of the existing brick/concrete surfaces of area n.exc 0.50 Sqm complete all as specified anddirected by the Engineer-in-Charge. 25 Dismantling water tank and removing to storeexeeding 250 but n.exc 500 ltrs complete all as specifed and directed by Engr-In-Charge. 26 S&F for rotational moulded polyethylene water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule complete all as specifed and directed.by Engr-In-Charge. 27 Dismantling water tank and removing to storeexeeding 500 but n.exc 1000 ltrs complete all as specifed and directed by Engr-In-Charge. 28 S&F for rotational moulded polyethylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule complete all as specifed and directed by Engr-In-Charge. 29 M&L for Cleaning of water tank of capacity exc 250 ltrs and n. exc 500 ltrs & removing all scale & dirt, etc., from tanks & from mouths of circulating pipes, etc. including disconnecting and refixing complete all as specified anddirected by the Engineer-in-Charge. 30 M&L for Cleaning of water tank of capacity exc 500 ltrs and n. exc 1000 ltrs & removing all scale & dirt, etc., from tanks & from mouths of circulating pipes, etc. including disconnecting and refixing complete all as specified anddirected by the Engineer-in-Charge. 31 Demolition ofwall and ceiling boards (fiber, pulp, insulation, etc.) or insulation boards/ slabs/ blankets/board fixed in aluminum door or partition, any thickness, including cover fillets & framed work if necessary complete all as specified and directed by Engr-In-Charge. 32 S&F 5mm thick ACPwall cladding sheet in colour as directed by Engr-in-charge fixed on MS frame size of section 25mmx50mmx3.25 mm. The size of each panel not exc 1.5sqm. MS frame to be fixed on walls, chajja and fasad with Min 08 Nos GI fastener 5 long per 1.5 sqm, including all necessary repairing work as reqd, two coat of synthetic enamel paint over one coat of red oxide primer, including weather sealing sealant, masking tape, including cutting of V groves to fixing moulded ACP sheet self-tapping screw complete all as specified and directed by Engineer-in-Charge.Note:-1.Work to be carried out upto four storey bldg with MS scaffolding 2. MS frame should be fixed on wall after painting. 33 M&L for PVC profile for wall paneling of size 23cm wide, 8mm over all thick and 01mm wall thickness fixed with screw to mild square tubular steel frame work mad e out of MS Hollowsection of size 25mm x 15mm x 2mm spacing 01 meter on both side frame work shall be fixed in wall with the help rawl plug and required length of screws and MS work shall painted with one coat of Red oxide primer for wall panelling,complete all as specified and directed by Engr-In-Charge. 34 S & FE board(Design: LACK & hill) : 605x605x4 mm thick, white pre laminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanized iron imposed grid with 24 mm wide T-section exposed flanges which shall be power coated white. The frame work shall be comprise of main runner made from 0.33 mm thick galvanised steel sheet and of size 24 mm X32mmX300 mm board spaced at 120 mm maximum center to center, hangers of GI wire4 mm dia to be fixed by approved rawal plug level and fasteners and screws etc.,The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall , flushing fitting of 1200 mm longer cross tee(with double stitching) to be interlocked between main runners at 600 mm center to center from 1200X600 mm modules cross tee longer than 600 mm to be supported independently . 600mm long cross tee centrally between the 1200 mm cross tee(with double stitching) to be interlocked between main runners at 600 mm center to center from 1200X600 mm modules cross Tee longer than 600 mm to be supported independently . The perimeter wall angle shall be 0.45 mm thick GS sheet of size 19 mm X 19 mm and 300 mm long of white colour all as per manufacturers instructions complete all as specified and directed by Engr-In-Charge. 35 S&F for 10-15mm thick exterior PVC wall cladding (Jalli) sheet of medium density in colour white or as directed by Engr-in-charge with computerized cutting as directed, fixed on MS frame. The size of each panel not exc 1.5sqm. MS frame to be fixed on walls, chajja and fasad with GI fastener 5 long per 1.5 sqm, including all necessary repairing work as reqd, two coat of synthetic enamel paint over one coat of red oxide primer, including weather sealing sealant, masking tape, including cutting of V groves to fixing molded PVC sheet with S/S self-tapping screw complete all as specified and directed by Engineer-in-Charge.Note:-1.Work to be carried out up to four story bldg with MS scaffolding . 2. MS frame should be fixed on wall after painting complete all as specified and directed by Engr-In-Charge. 36 M&L for providing & fixing infalse ceiling with Semi perforated 12mm thick acoustical false ceiling, (fire retardant and sound absorbent) micro regular edged at all heights with GRG (Glass Fibre reinforced Gypsum) false ceiling tiles of size 595x595 mm of approved texture, design and pattern having moisture content less than 2%, humidity resistance of 99% NRC 0.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 475 (Part 4) -1970 and light code description unit rate No 429 Sub Head : 26.0 NEW TECHNOLOGIES AND MATERIAL reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T-Gridof hot dipped galvanised iron section of 0.33 mm thick (galvanised @ 120 grams per sqm including both sides) comprising of maint -T runners of size 15x32mm of length 300mm, cross -T of size 15x32 of length 600mm to form grid module of size600x600mm , suspended from ceiling using galvanised mild steel items (galvanising @80 grams per sqmm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-Shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on perimeter wall /partition with the help of plastic rawl plugs at 450mm centre to canter and 40mm long dry wall screws.The work shall be carried out as per specification, drawing and as per direction of the Engr-in charge. 37 M&L for Providing and fixing in position wall panelling at all heights (fire retardant and sound absorbent) with GRG ( Glass Fibre Reinforced Gypsum) panels/tiles of10 mm thick fully perforated suitable for acoustic purpose of size 595 x 595 mm of approved texture, design and pattern having moisture content less than 2%, humidity resistance of 99%, NRC 0.70 to 0.85 as per IS 8225:1987, Non combustible as per BS 476 (Part 4)-1970 and light Reflectance of 75% to 85% (Minimum), comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanising @ 120 grams per square metre including both sides) i.e vertical studs of size 48 x 34 x 36 mm are placed at 600 mm centre to centre in a floor and ceiling channel section ofnickel coated size 50 x 32 mm fixed to the floor and ceiling at 600 centres using 12 mm dia, 50 mm long wedge type expanded zinc alloy dash fasteners with 10 mm bolt. The same channel is then to be fixed in horizontal direction at 600 centre to centre so as to form a grid of 600 x 600 mm. Glass wool of 50 mm thickness is then to be inserted in the slots and finally GRG ( Glass Reinforced Gypsum) non combustible panels/tiles are to be screw fixed with self tapping pan head nickle coated mild steel screws of size 13 x 3.2 mm on this grid leaving an even groove of 1 mm between the panels. The joint between the panels are to be duly jointed and finished using recommended jointing compound and fibre joint tape roll 50 mmm wide ( 90 meter) roll and two coats of primer suitable for panelling as per manufacturers specifications complete all as specified and directed. 38 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge 39 M&L for Non-SkidColoured Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified anddirected by the Engineer-in-Charge . 40 M&L for Screed bed or bedding layer 15 mm thick in CM (1:6) for laying floor finishes/ paths etc., complete all as specified and directed by Engr-In-Charge. 41 M&L forvitrified ceramic tiles 9 to 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 15 mm th screed in cement mortar 1:6 complete all as specified and directed by Engr-In-Charge. 42 M&L forVitrified Ceramic tiles light shade/ /double charge/ ultracharged 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 15 mm thick screed in cement mortar 1:6 complete all as specified and directed by Engr-In-Charge. 43 All as per item No 42 here in beforebut in dado/Skirting over 10mm thick rendering in CM 1:4 44 M&L for Glazed Coloured Ceramic tiles in vertical surface 300x200x7mm (or) 350X450X6 to 7 mm thick set and joint in neat cement slury and pointed in white or colour cement to match the colour of the tiles,complete all as specified anddirected by the Engineer-in-Charge . 45 M&L for Rendering or bedding layer for tiles as in vertical surfaces 10 mm thick in CM (1:4) for back coat. Complete all as specified and directed by Engr-In-Charge. 46 M&L for coloured chequered cement concrete tiles30cmX30cm x22/25 mm thick, set, jointed & pointed in neat cement slurry with grey cement and pigment over 20 mm screed bed in CM (1:6) ,complete all as specified anddirected by the Engineer-in-Charge 47 Demolition of concrete of any description and in any position not otherwise specifically provided for.complete all as specified and directed by Engr-In-Charge. 48 M & L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection complete all as sepcified and directed 49 M&L for Machine pressed colouredprecast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of60 mm thickness M-35 Grade.complete, with grey cement andpigment complete all as specified and directed by Engr-In-Charge. 50 M&L for75 mm thick Cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub floors, sub bases , floors and pavings/ paver blocks etc complete all as specified and directed. 51 M&L for for sand filling under floors or in foundation including watering and consolidationfor cushioning as in interlocking paver blocks laying complete all as specified and directed by Engr-In-Charge. 52 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.laid,bedded and pointed in any mortar complete all as specified and directed by Engr-In-Charge. 53 M&L for 16-18mm thick Granite slab on top of cooking plateform, bar counter stairs etcand simillar work including cutting polishing rounding on edge etcmachine cut, bedded andjointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15mm thick screed bed in CM 1:4. including grinding and polishing complete all as specified and directed by Engr-In-Charge. 54 M&Lfor 16-18mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall with any height) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, cutting polishing rounding on edge etcmachine cut, bedded,jointed with grey cement slurry, pointed with white cement with admixture of pigment to match the shade of granite stone and holding with brass screw complete all as specified and directed by Engr-In-Charge. 55 S & F in repair Aluminium door single leaf with anodized aluminium frame of section 62.5 x 37 x 2.5 mm thick, shutter with bottom & middle rail of section 112.50 x 37 x 2.5 mm thick and styles & top rail of section 83 x 37 x 2.5 mm thick with centrally locking arrangement with lock 7 lever and self closing device with rebate includingjointingcleats, fixing of builders hardware fittings, necessary numbers of floor spring and glazing with 5.5 mm thick ordinary plain glass includingnecessary fittings, fixtures & aluminium snap beadsComplete all as specified and directed. 56 S&F as in repair powder coated (minimum thickness of powder coating 50 micron) aluminum anodized three track slinding window with two or more shutter with 5 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing ,handle lock,etc rubber beading and glazing clips etc using following sections as given in JINDAL catlogue etc as specified as per manufacturer instructions with the following size, complete all as specified and directed by Engr-in-Charge.Note : Glass and wire not measured and paid separately however cost of all other connected accessories deemed included in unit quoated rate. 57 S & F in repair for aluminium partition frame work anodized frame of size 62.5x37x2.5 mm thick with bottom 7 middle rails of aluminium section 62.5x37x2.5mm thick and styes, top of section 62.5x37x2.5 mm thick including jointing cleats, filled with 12 mm thick pre laminated partical board interior grade up to middle rail from bottom and 5 to 6 mm thick plain/frosted glass/aluminum chequered grill of anodized section of mesh 100x100mm of 08 mm dia of bar fixed to frame with 20x20 mm aluminum flat with mire mesh fixed with screw and necessary fittings fixtures complete all as specified and directed 58 Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm each,incl removing complete all as specified and directed by Engr-In-Charge. 59 S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners not paid for separately and fair finish should be given to jambs ).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. 60 S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60(Suspension Grade), 2, 4, or 6 raised panel design calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified anddirected by Engineer-In-Charge. 61 S&F Butt hinges of size 100mm length, extruded aluminium alloy with galvanished mild steel hinges pin, anodized & fixed, type C-21 complete all as specified and directed by Engr-In-Charge. 62 S&F 150mm Alluminium, anodized, barrel tower bolts extruded section.complete all as specified and directed by Engr-In-Charge. 63 S&F 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified anddirected by the Engineer-in-Charge. 64 S&F Mortice lock, fency type, 4 leavers, verticle type, brass body, size 100 mm, all as directed by Engr-in-Charge. 65 S&F in repairs Gun-metal, glabe or gate valves, with iron wheel head, screwed both ends for iron pipe & fixed dia of bore of pipe 20mm complete all as specified and directed by Engr-In-Charge. 66 Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and as directed by the Engineer-in-Charge. 67 M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. 68 S&Fin repair Vitreous china coloured wash down water closet pan one pieces (Couple closet) with P or S trap, Soft close PVC seat cover and twin flushing cistern complete all as specified anddirected by Engineer-in-Charge. 69 S&F in repairplastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified anddirected by Engineer-in-Charge. 70 S&F in repairs heavy duty Mortice lock, fency type, 4 to 6 leavers, verticle type, brass body, with push and pull handle, Complete all as specified anddirected by Engineer-in-Charge. 71 S&Fin repairs Door closer hydraulically regulated Alluminium (Die cast) body design No-3 universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed by Engr-In-Charge. 72 S&F in repairs 32mm bore and 75cm long PVC flexible waste pipe for WHB complete all as specified and directed by Engr-In-Charge. 73 M & L in repairs for 35 mm thick Type B-0 (1:2:4) (using 12.50 mm graded stone aggregate) set in CM (1:4) Providing precast cement concrete louvres and jallies, including all mouldings and reapiring/ finishing/ colouring of disturbed surfaces , complete all as specified and directed by Engr-In-Charge. 74 S&F in repair two legged aluminium floor door stopper with rubber shoe 140mm long complete all as specified and directed by Engr-In-Charge. 75 S&F in repair for floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size),complete all as specified and directed. 76 S&F steel water tubing, galvanised,medium grade, ISI marked with all fittings andfixed on walls and ceilingsor laid in floors bore of pipe 15 mm complete including taking down or up 15 mmsteel water tubing and removing to store complete all as specified and directed by Engineer-in-Charge. 77 S&F steel water tubing, galvanised,medium grade, ISI marked with all fittings andfixed on walls and ceilingsor laid in floors bore of pipe 20 mm complete including taking down or up 20mmsteel water tubing and removing to store complete all as specified and directed by Engineer-in-Charge. 78 S&F in repair CP bib taps long body , cast copper alloy, fancy type with crutch or butterfly handles, chromium plated, screwed down to iron pipes or for brass ferrule of 15 mm borecomplete all as specified and directed by Engr-In-Charge. 79 S&F in repair CP stop/angle valves, cast copper alloy, fancy type, chromium plated with long shank & cup (concealedtype) with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed by Engr-In-Charge. 80 S&F in repair two way angle stop valves, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm borecomplete all as specified and directed by Engr-In-Charge. 81 S&F in repair Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hookcomplete all as specified and as directed by Engineer-in-Charge. 82 S&Fin repair 15 mm pillar taps cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nutsscrewed for iron pipes and fixed , fancy typecomplete all as specified and directed by Engr-In-Charge. 83 S&F in repairs Vitreous China urinal half stall type, white complete all as specified and directed by Engr-In-Charge. 84 S&F fancy type mirror of8 to 10 mm thick glossy glass decorative/ designer type, any size and shape bevelled edges all-round as decided by EIC, wall mounted mirror complete all as specified and directed by Engineer-in-Charge. 85 S&F in repair for CP towel railof 15mm dia with hook 600mm long complete all as specified and directed by Engr-In-Charge. 86 S &F in repair Toilet paper holder with flat recessary type stainless steelcomplete all as specified and directed by Engr-In-Charge. 87 M & Lforcompleteremovalofexistingrooftreatment (Mud puska, Cement Tiles, bricks or Old APP Roof treatment and vegetation from root) including bedding layer in cement mortar/Mud anddisposedfrom MoD landcomplete all as specified and directed by Engineer-in-charge. 88 M&L PCC 1:2:4type B1 (using 20mm graded stone aggregate) mixed with3.00% liquid water proofing compound of weight of cement laid 25 mm thickness as in padding over roof slabs for providing proper slope to the concrete padding, surface finished even and smoothwithout using extra cement complete all as specified and directed by Engineer-in-charge. 89 M&L for five layer prefabricated atactic polypropylene polymer (APP) modified 3 mm thick membrane ( weight not less 3 kg/sqm) reinforced with 160 gms polestar non-woven fabric with scratched tool before finishing roof surface. When the concrete surface is still green, 10 mm thick 1:4 cement plaster shall be laid, the roof surface shall be thoroughly wire brushed washed dried up and cleaned of all foreign matter and dust prior to the application of primer on the dried surface, one coat of approved bituminous primer having density in the range of 0.87 to 0.89 / kg at 25 degree and viscosity of 70 to 160 CPS manufactured by the same manufacturer @ 0.40 litres/sqm shall be applied. APP membrane shall be laid on primed surfacetorch application method after allowing 24 hours of primer to dry. Laying of APP membrane shall be commenced at the lowest level and worked upto the crest. APP membrane will normally be laid in length at right angle to the direction of slope. The overlaps shall be of minimum 100 mm on longitudinal direction and 150mm on the transverse direction. All overlaps shall be bonded with bitumen primer and levelled by the heating the overlaps with butane torch. This treatment shall be done by theapproved authorized applicator. Guarantee of treatment shall be for 10 years. Thereafter APP membrane shall be painting with two coat of water proofing paint with aluminium finish.(ii) Independent testing of membrane for the approval technical parameters specified here in after shall be carried out the approved laboratories like National test house any other Govt approved laboratory having facilities for the testing of membrane. 90 S&F in repairs for white vitreous china battery based infrared sensor operated urinal of size 295 x 325 x 575 mm having water inlet from back side, including fixing to wall with suitable brackets and sensor all as per manufacturers specification and directioncomplete all as specified and as directed by the Engineer-in-Charge. . (Make: Hindware - Flow with integrated sensor CAT Part No 60021/or equivalent in Cera, Parryware etc. 91 S&F in repair vitreous china wash basin white oval type size as directed by EICwhite in colour, fitted in counter platform of granite stone (Granite stone shall be measured separately) including waste coupling for WHB with long screwed and shanks and fly nuts, flanged end bedded in red lead and other end fixed, PVC waste pipe, 32mm dia ,medium grade, pipe with fittings fixed in wall connected to floor trap for drain out, completeall as specified. 92 S&Finrepair110 mmborePVC (SWR ) pipesinglesocketedinany lengthwithrubber ringjoints, laidintrenchesorinfloorsetcincludingremovingfromsite complete all as specified and directed by Engineer-in-Charge. 93 S&Finrepair75mmborePVC (SWR ) pipesinglesocketedinany lengthwithrubber ringjoints, laidintrenchesorinfloorsetcincludingremovingfromsite complete all as specified and directed by Engineer-in-Charge. 94 Supply and fixing in repair 4.00 mm thick ordinary quality sheet glass exe 0.5 sqm in each paneof glazing with oil putty /beading etc complete all as specified and directed by Engineer-in-Charge. 95 S & F as in repair 12mm thick Toughned glass as in hinged doors, partitions, sliding doors, automatic doors and similar work of approved brand and manufactures, including cutting to shape, drilling holes required, including Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specifiedand directed by Engr-in-Charge.Note:- Rate included all nessesry fitting and frame work for glass fitting, provision of top and bottom pivots, S/S handle, hinges, double action floor spring, stoppers etc. complete all as specifiedand directed by Engr-in-Charge. 96 S&F in repair vertical venetian blinds made out of nylon cloth of any colour 100mm wide strip as aprroved including hanging arrangement rollers etc complete all as specified and directed by Engr-in-Charge. 97 M&L Repair of automatic sensor glass door its motion motors or safety sensor or all mechanical part(Sliding door (dorma xl-c4125,150mm height 4 mtr (approx),complete allspecified and as per manufacturerinstructions or as directed by engineer in charge .
