Tender For Supply, Installation, Testing And Commissioning Of Conical Poles At Sector-14A Flyover, Noida - Supply And Fixing Of 9000 Mm Conical Arch Pole Made Of Continuously Tapered Circular Hot Rolled Steel Curved Sheet (Bsen 10025 S355). Total Height I, noida-Uttar Pradesh

Tender For Supply, Installation, Testing And Commissioning Of Conical Poles At Sector-14A Flyover, Noida - Supply and fixing of 9000 mm conical arch pole made of continuously tapered circular hot rolled steel curved sheet (BSEN 10025 S355). Total height including with 2150 mm long bend radius. The pole should have minimum 185mm Bottom dia, 75mm Top dia 3mm thick HT Sheet, the base plate have minimum dimension of 275x275x16mm thick steel of grade E-250 to IS:2062 :2011 with 4 elongated holes 48x24 to suit M20X500mm bolts with grade 5.6 at CC215 having MS service door. The base plate have a cable entry hole of minimum 70mm dia at the centre. This mounting steel plate along with foundation bolt of suitable size to be used for ensuring firm grouting into the specially design foundation. Pole section welded by certified Welders using high end MIG welding process. The control gear tray is prewired with 2.5 Sqmm cable, 6A SP MCB and 32 Amp+ B7 Stud type 4 way terminal block for loop/loop out arrangement, 5A 2 Way terminal connector and provision for earthing (all cables etc. are in contractors scope). The pole should be hot dip galvanized and have PU Painting/Coating of min. thickness 60 to 80 Micron. All dimension are within 5% tolerance. The pole shall be provided with graphite gray/Anthracite grey/Black as standard colour options. The pole should strictly follow as per GA drawing. Including nut, bolt and all T&P Material as per direction of E/I.(AOR) (Make- K Lite/Kesslec/Neri/Transrail ) 2 Supply of adaptor bracket suitable for 9.0mtr height conical bended pole size 350mmX350mm and 15mm thick MS Plate L shape bracket as per given drawing all t&p material etc as as per direction of E/I. .(Make- K Lite/Kesslec/Neri/Transrail ) 3 Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PS 501 50 sqmm 3.5 core 4 16 sqmm 4 core 5 Supply and fixing of plain or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and makingonnection etc. complete in all respect as perdirection of the Engineer-Incharge. PS No. 504. 16 sqmm 6 50 sqmm 7 Supply and fixing of aerodynamically designed adjustable curved shaped street light suitable for installation oncurved poles, luminaire Housing and front frame made of pressure die-cast aluminium featuring high strength and anti corrosion. The front frame of the luminaire should be hinged for easy open and ease of maintenance. light fitting should have inbuilt tilting facility for mounting on to Ø60 pipe at -15° to +°15 lateral (side entry) and vertical (top mount). Led compartment should be covered with Clear tempered glass or poly carbonate cluster lens. High quality light transmittance lens must be used. Power consumption should be between130-150W at steady state full intensity luminaire, the delivered luminous flux of the luminaire should be minimum 150-160 lm/Wfor 4000K Distribution- Asymetrical Batwing street light optics T-II. The ingress protection is IP-66 or higher and impact resistance of IK08. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire >60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 6KV.Driver operating voltage of 100-277Vac.Adequate heat sink with proper thermal management shall be provided. The fixtures proposed must have passed LM 79 & LM-80, Reports from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material. Fitting design should be as per directed by E/I. Light fitting should have minimum 5 years of warranty. Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN. CE & BIS Certified (AOR) (Make- K Lite/Kesslec/Neri/LT ) 8 Supply and laying 90 mm dia DWC ( Double wall corrugated pipe across the road by Trenchless method (Manual). Complete in all respect as per direction of E/I. (AOR) 9 Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect. PS. No. 807 f (ii) 40 A TPN 10 Supply & erection of overhead line with G.I. wire no. 8 to 4 SWG on poles/serivce bracket including binding etc. complete in all respect.P.S. No. 628 11 Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm G.I. strip, upto switch board (from apron to switch board, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing. PS. No. 725 (B) 12 Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. PS No. 716 13 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. DSR 14.16.1a) 63 mm dia (OD-63 mm & ID-51 mm nominal) 14 Supplying and drawing sizes of FRLS PVC Insulated Copper Conductor. Single core cable in the existing surface/recessed steel/PVC Conduit as required. (DSR Elect 2018/1.17.3/P-4) 3X1.5 Sqmm

INR 2832 /-

INR 132900.0 /-

INR 66.41 Lakhs /-