Tender For Repair/Maintenance Of B/R Works In Mes Installations At 33 Fad Dappar Under Age (I) Dappar
Tender Value
Ref. Documents
Estimated cost
Bid Submission
12 Jul 2025
0 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
dappar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Repair/Maintenance Of B/R Works In Mes Installations At 33 Fad Dappar Under Age (I) Dappar; 1. 11 Old Unsv chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm Each 4.00 500.00 2000.00 2. 12 Old Unsv chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm not exceeding 4.00 sqm Each 6.00 600.00 3600.00 3. 35 Old Unsv asbestos cement, (Corrugated, semicorrugated etc) sheets Sqm 162.00 50.00 8100.00 4. 1 & 38 Old unsv scrap iron/steel Kg 2800 30.00 84000.00 1. CONCRETE (a) (a) Integral cement water proofing compound. (b) Plywood for concrete shuttering work. 2645 4990 2. JOINERY (a) Wooden flush door shutters, solid core type, ply wood face panels (Sixth Revision). (b) Wooden flush door shutters, solid core type, ply wood face panels and hard board panels (Third Revision) 2202 (Part-1) 2202 (Part-2) 3. BUILDERS HARD WARE (a) Steel butt hinges. (b) Non–ferrous metal butt hinges. (c) Ferrous tower bolts. (d) Non-ferrous tower bolts. (e) Door handles. (f) Parliament hinges. (g) Hydraulically operated door closures. (h) Continuous (piano) hinges. (i) Non-Ferrous metal sliding door bolts. (j) Tee and strap hinges. (k) Mild steel sliding door bolts. 1341 205 204 (Part-1) 204 (Part-2) 208 362 3564 3818 2681 206 281 4. ROOF COVERINGS Bitumen felts for water proofing and damp proofing 1322 5. CEILING AND LINING (a) Ply wood for general purpose. (b) Block boards. (c) Veneered decorative plywood. (d) Marine plywood. (e) Fiber hard boards. (f) Veneered Particle Board (Exterior Grade) (g) Decorative thermo setting synthetic resin bonded laminated sheets 373 1659 1328 710 1658 3097 2046 6. FLOORING (a) White Portland cement (b) Cement Concrete flooring tiles. 8042 1237 7. WATER SUPPLY, PLUMBING, DRAINS & SANITARY APPLIANCES (a) Concrete pipes (with and without reinforcement) (b) Flushing Cistern for WC and urinals. (c) PVC flushing cistern. (d) Cast copper alloy screw down bib tap and stop valves for water services. (e) Galvanized mild steel tube (f) Galvanized mild steel tube fittings Centrifugally cast (Spun) Iron spigot and socket; soil, waste and vent pipes, fittings and accessories. 458 774 7231 781 1239(Part-1) 1239(Part-2) 3989 Srl No 7. (Contd…) (h) Ball valves (Horizontal plunger type) including floats for water supply purposes. 1703 (j) Cast iron manhole covers and frames. 1726 (k) AC pressure pipes. 1592 (l) Automatic flushing cistern. 2326 (m) Vitreous China ware appliances:- (i) General requirements. (ii) Wash down water closet. (iii) Squatting pans. (iv) Wash hand basin. (v) Laboratory sinks. (vi) Urinals and partition plates (vii) Specific requirements of accessories for Sanitary Appliances (Third Revision) 2556 (Part-1) 2556 (Part-2) 2556 (Part-3) 2556 (Part-4) 2556 (Part-5) 2556 (Part-6) 2556 (Part-7) (n) Plastic WC seats and covers. 2548 (o) Pillar taps. 1795 (p) Centrifugally cast (spun) iron pressure pipes for water, gas and sewage. 1536 (q) Rubber sealing rings for gas mains, water mains and sewers. 5382 (r) Cast iron fittings for pressure pipes for water, gas and sewage. 1538 (First Revision) 8. ELECTRICAL WORKS (a) Ceiling roses. 371 (b) Rigid steel conduit. 9537 (Part-2) (c) Rigid non-metallic conduit. 3419 (d) Starters for fluorescent lamps. 2215 (e) Aluminium conductor for overhead transmission purposes. 398 (f) Porcelain insulators for overhead power lines. 731
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 07-Jul-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 12-Jul-2025 |
BOQ
| Sl. No. | Item Description |
| 1 | BOQ (REPAIR/MAINT OF B/R WORKS IN MES INSTALLATIONS AT 33 FAD DAPPAR UNDER AGE (I) DAPPAR.) |
| 2 | Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition), complete all as specified and directed. |
| 3 | Material and labour for precast RCC(1:1½:3), nominal mix, type A-1 uising 20mm gradedstone aggregate as in cover slab of drain set in cm 1:4, complete all as specified and as directed .Note:- Reinforcement shall be measured seperately |
| 4 | Material and labour for mild steel TMT bars 10mm dia & over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.(NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.) |
| 5 | Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15cm thickness below or above ground level of any description and in any positionincluding removing rubbish material from building and thrown in low lying empty area outside of the MOD land, complete all as specified and as directed by Engineer-in-Charge |
| 6 | Material and labourfor100mmthickPCC1:3:6typeC-2 (using 40mm graded stone aggregate)asinsub base flooring/hard standing, complete all as specified and directed. |
| 7 | Material and labour for 60mm thick precast cement concrete (M-35) colour rubberised factory made, machine pressed interlocking paver blocks, with grey cement and pigment any shape and size as approved by AGE(I), laid over and including 25mm thick sand cushion consolidated properly before and after laying of paver block including dismantling of paver blocks, complete all as specified and directed. |
| 8 | Material and labour for 50mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) laid in alternate panel in floorings including finishing the surface even and smooth without using extra cement, complete all as specified and directed. |
| 9 | Supply only plastic dividing strips,1.5mm thick and 38mm wide inserted in position confirm to design, complete all as specified and as directed by Engineer-in-charge. |
| 10 | M&L for 100mm thick, PCC 1:4:8 type D- 2 (using 40mm graded stone aggregate)in sub base, flooring, pavings etc, complete all as specified and directed. |
| 11 | Material and labour for Chequered cement concrete tiles 20cm x 20cm x 25mm thick With greypigment cement and pigments,set, jointed and pointed in neat cement slurry in floors over 20mm thick screed bed in cement mortar 1:6, including dismantling of chequered cement concrete tiles, complete all as specified and as directed by Engineer-in-charge. |
| 12 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) areanot exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by Engineer-in- charge. |
| 13 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) areaexceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by Engineer-in- charge. |
| 14 | M&Lforfactory made Pressedsteelframesofsize105mmx60mmmadeof 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified and asdirected by Engineer-in- charge |
| 15 | Material and labour PCC (1:2:4) type B1 using 20mm graded stone aggregate as in holdfast blocks/ filling in chowkats, complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply & fixing factory made flush shutters 30mm thick ply construction, BWP confirming to IS 2202, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick lipping frame to match including supply and fixing following items :(a) MS medium weight Butt Hinges 100mm -3 nos. per leaf(b) Aluminium tower Bolt 200mm long - 2 nos per leaf(c) Aluminium handles 150mm - 2 nos. per leaf(d) Aluminium sliding door bolt 300mm - 1 no. per leaf(e) Aluminium floor door stooper 150mm long- 1 no. per leaf. |
| 17 | Providing and fixing in repair factory made extruded aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60mmX44.45mmX1.29mm and shutters made of 63.5mmX31.75mmX1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperturesin inner shutters complete fixed in all respect as specified including supply and fixing following items :-(a) Stainless steel (304 Grade) finished butt hinges 150mm -2 nos per leaf.(b) Powder coated aluminium tower bolt 150mm long - 2 nos per leaf.(c) Powder coated aluminium handles 150mm - 1 no per leaf. |
| 18 | Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5mm X 38.10mm X 1.29mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size, completeall as specifiedand directed. |
| 19 | Supply & fixing factory made aluminium 50 micron powder coated grill, fixed in position in windows, completeall as specifiedand directed. |
| 20 | Material and labour for figured glass, pin headed type, 4mm thick and glazing with oilputtyorwoodenbeadsinsquaresnotexc.0.5sqmineach pane including hackingoutoldbrokenglass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. |
| 21 | Material and labour for preparation ofnew wooden or wood based surfacesof any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in- charge. |
| 22 | Supply & fixing in repair butt hinges medium weight cold rolled mild steel of 100mm size ISI marked, complete all as specified and directed by the Engineer in Charge. |
| 23 | Supply and fixing in repair extruded aluminium alloy handles, fabricated type, 150mm long fixed with and including steel screws, complete all as specified and as directed by Engineer-in-charge. |
| 24 | Supply and fixing in repair aluminium anodised barrel tower bolt of extruded section, 150mm longfixed with and including steel screws complete all as specified and as directed by Engineer-in-charge. |
| 25 | Material and labour for angle iron postsand struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling,boltingor riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed byEngineer –in-Charge. |
| 26 | Material and labour for prepration of new or previously untreated steel surfaces of any description over 10mm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 27 | Material and labour for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete including fabrication as directed, including hold fast, locking arrangement, sliding door bolt, stopper etc conforming to Fe-410-W (Gde E-250) quality A, complete all as specified and as directed by Engineer-in- charge |
| 28 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified and directed byEngineer –in-Charge. |
| 29 | Supply only Chain link MS galvanisd fencing of size 100mmx100mm, 3mm thick, any size or type, complete all as specified and directed byEngineer –in-Charge. Note-Weight of chain link fencing shall be assessed by BOO |
| 30 | M&L for mild steel round bars 10mm dia and over, cut to length, bent to shape requiredas in tying rod for chain link fencing, complete all as specified and directed byEngineer –in-Charge. |
| 31 | Material and labour for preparing new surfaces of steel and iron work,of any description and girth, not otherwise described, treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area not exc 0.1 sqm with tar or coal tar black paint, complete as specified and as directed by Engineer-in-Charge. |
| 32 | Material and labour preparing new treated/painted steel and iron surfaces of any description, not otherwise described, not exc 10cm width or girth and applying two coats of synthetic enamel paint (First quality) over one coat of zinc chrome primer, complete all as specified and directed. |
| 33 | Material and labour for PCC (1:2:4) Type B0 using 12.5mm graded stone aggregate as in coping etc and including weathering slightly rounded or chamfered angles and throating, complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fixing of galvanised. 2 strand, steel barbedwire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mildbsteel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fixing for mild steel screws bolt (Machine made) with hexagonal or square heads one end screwed, each screwed end have one washer and one nut, dia of shrunk 5mm-10mm and length of bolt exc 5cm and not exc 10cm, complete all as specified and directed. |
| 36 | Dismantling of asbestos cement, (Corrugated, semicorrugated etc) sheets in roof coverings, complete all as specified and directed. |
| 37 | Material and labour for pre-painted galvanlume aluminium zinc coating havingGI based corrugated steel sheets 0.50mm thick of any colour and shape of sheet approved by AGE(I) as in tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screw, complete all as specified and directed. Note: (i) shape of sheet approved by AGE(I)(ii) Fixing of sheets will be done strictly according as per manufacurer\"s instructions. |
| 38 | Material and labour for pre-painted galvanlume aluminium zinc coating havingGI based plain steel sheets 0.50mm thick of any colour and shape of sheet approved by AGE(I) as in tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screw, complete all as specified and directed. Note: (i) shape of sheet approved by AGE(I)(ii) Fixing of sheets will be done strictly according as per manufacurer\"s instructions. |
| 39 | Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed. |
| 40 | Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, in hard and dense soil, completeall as specified and directedby Engr-in-Charge. |
| 41 | Supply and fixing joist channel angle or tee sections fixed independentely with out connecting plate Etc of Fe-410 W Gde E-250 quality A, complete all as specified and directed. |
| 42 | Supply and fixing mild steel forframed structure liketrussed, purlins, crane gantries,postrails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels, tubes,flate sections) including distance pieces, cleats etc conforming to Fe410-W (Gde-E-250) quality-A, complete all as specified and directed. |
| 43 | Supply and fixing of plates ( plain or chequered ) channels squre cut or notched ordinary and counter sunk forming holes with riveted ,bolted or welded attachment FE-410W-( Gde-E 250 ) quality A for using pit cover, tank cover,Floculator etc. complete all as specified and directed. |
| 44 | Material and labour for mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end tobefittedwith washers and one hexagonalor square nut. exc 30cm long, dia of neck not exc 12mm, complete all as specified and directed . |
| 45 | Material and labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in post and truss, complete all as specified and directed. |
| 46 | Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. |
| 47 | Material and labour forrendering 10mm thick in cement mortar (1:6) on fair faces of Brick walls or concrete surfaces, finishing the surface fair and even complete all as specified and as directed by the Engineer-in-Charge. |
| 48 | Material and labour for rendering 15mm thick in cement mortar (1:4) on otherthan fair faces of Brick walls or concrete surfaces, including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.(Note :- WPC shall be measured & paid separately as Supply only) |
| 49 | Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. |
| 50 | Material and labour for rendering 5mm thick in cement mortar (1:3) on concrete surfaceof ceiling, finished fair, even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. |
| 51 | Material and labour for Preparation ofnew plastered Internal wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:-(a)Applying Wall care putty 1.5mm thick in two layers on complete surface and smoothening the surfcae with sand papers / by Mechanical method (hand electric grinder) prepatory to paint as directed. (b)Two coats of distemper oil emulsion (interior) of approved tint/shade (Company Depot Tinted) over a coat of primer (interior) by using paint Roller. |
| 52 | Material and labourfor preparing of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. |
| 53 | Material and labour for preparation ofnew plastered external wall surface by sand papering or by any other mean and after preparing the surfaces two coats of exterior emulsion paint of approved tint/shade (Company Depot Tinted) over a coat of primer (external) by using paint Roller/brush, complete all as specified and as directed by Engineer-in-charge. |
| 54 | Material and labour for preparation ofnew plastered external wall surface by sand papering or by any other mean and after preparing the surfaces two coats of exterior emulsion paint of approved tint/shade (Company Depot Tinted) over a coat of primer (external) by using paint Roller/brush, complete all as specified and as directed by Engineer-in-charge. |
| 55 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 56 | Material and labour for light shade virified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles including 15mm thick screed in cement mortar (1:6) as in floors etc,complete all as specified and directed. |
| 57 | Material and labour for light shade virified ceramic tiles 10mm thick (square/ rectangular) polished, as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over 10mm thickrenderingCM 1:4,complete all as specified and directed. |
| 58 | Material and labour for glazed ceramic coloured tiles in vertical surfaces such as skirting, dados and riser to steps etc size 250mmx350mmx7mm /450mmx350mmx7mmthick set and jointed in neat cement slurry and pointed in white or colourcement to match laid over including 10mm thickrenderingCM (1:4), complete all as specified and directed. |
| 59 | Material and labour for joint free non-Skid whilte ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed bedding layer in CM 1:6, complete all as specified and directed. |
| 60 | Material and labour for water proofing treatment onroof surface in following sequence through manufacturer / authorised applicator of the manufacturer complete :-(i) Properly cleaning and drying concrete surfaces.(ii) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm(iii) Laying 3mm thick APP modified water proofing membrane with 100mm over laps sealed and bounded to the surfaces by \"torchon\" method.(iv) Applying a coat of bituminius aluminium paint @200 gm /sqm (minimum ) in two coats |
| 61 | Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 18 of tender documents. |
AI Tender Summary
Tender Timeline
Jul 07, 2025
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 12, 2025
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedJul 12, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJul 14, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender