Repairs To Drain, Culverts, Small Arm Range At Domestic Area At 25 Ed Af Stn Deolali; Labour only for sieving of fine sand(river sand) and saw dust mix and removal of excess size granulars & waste materials and spreadinig the mix of fine sand saw dust material as per required gradient placing in that manner if 16mm plain bar drop from 1mtr height it will be penetrate into the spreading saw dust and fine sand material upto 900mm also adding additional saw dust and fine sand to maintained the level in ratio of 1:1 as directed by Engr-in-Charge. Note:- (i) Payment of fine sand (river sand)& saw dust measured and paid separately at separate item. (ii) Upto a height of 900mm entire mix of Fine sand and saw dust to be removed (iii) Stack mesurment shall be carried out. (iv) seiving the mix of fine sand (river sand) and saw dust carried out by using mechinery seiving as per std size. (v) After sieving, the materials are shifted in range up to a height of 8m with sufficient gradient. (vi) Addl Fine Sand (river sand) and saw dust to be filled as required on range. , Supply only fine sand (River sand) as directed by Engr-in-Charge. , Supply only fine saw dust as directed by Engr-in-Charge , M & L for filling of sands in bagsand stacking thebags with a height of 1.2m complete all as spd and as directed. , Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars but excluding ashlar facing, dressed stone work and precast concrete articles etc all as specified & as directed by Engr-in-Charge. , Taking down cement plaster of any description, on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete. , M & L for rendering 15 mm thick in CM1 :4 on fair faces of brick work or concrete surfacesfinished even and smooth without using extra cement complete all as specified & directed by Engr-in-Charge. , Demolition of cement concrete (unreinforced)in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed . , M&L for Cement concrete 1:4:8 Type-D2 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed . , M & L for brick work with sub-class `B bricks Old size , straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6. , M& L Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in Cement mortar 1:6 , M&L for Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling,uncoursed or brought upto courses complete all as specified and directed . , M & L for rendering 15 mm thick in CM1 :4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing finished even and smooth without using extra cement complete all as specified & directed by Engr-in-Charge. , M&L for Cement concrete 1:2:4 Type-B1(using 20mm graded aggregate) as in surface channels and drains complete all as specified and directed . , Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement , including forms, moulds, mitred/stopped ends etc , M&L for Providing Cement concrete 1:2:4 Type-B1(using 20mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs ,back filling of PS frame, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed (including necessary form work)complete all as specified and directed by Engineer-in-Charge. , Supply and fixing mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe.290, Gde-E-265 complete all as specified and as directed. , M&L Preparation of new previously untreated steelsurfaces of any discription ,n exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. , S&F Precast SFRC cover (Steel fiber reinforced concrete) of grade designation HD - 20 ISI Marked (IS 12592-2002) cover of size 1200 x 600 / 600 x 600 (thick as per site) with edge protection MS Flat 75mm x 5 mm of load bearing capacity of wheel load between 50 to 100 KN including handle, bar etc complete all as spd and as directed. , Reinforcement cement concrete M-25 ( Design mix)as inFoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, drain wall complete all as specified and directed. , Use and waste of form work to faces of walls, retaining wall, abutments,parapets and staircase railing similar work footings including attached pillasters, buttresses etc, vertical or to batter complete all as spd and as directed. , Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips completeall as specified & directed . , Providing precast ce- ment concrete 1:2:4 Tybe B-1 with using 20mm graded stone aggregate as cover slabs (for man hole etc) chullah hoods, chajjas, water troughts, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 including necessary use and waste from works etccomplete all as specified and directed by Engineer-in-Charge. , Material and labour for mild steel TMT steel bars 6mm to 8mm dia and over,cut to length, bent to shape required including cranking, bending and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. , M&L for preparation of old decorated surfacesof walls by washing, rubbing down and stoping of painted surfaces and applying one coats of Cement Base Paint complete all as specified and directed. , M&L for complete removal of existing treatment on walls including washing down, rubbing downand applying two coats of Cement Base Paint complete all as specified and directed. , Supply and fixing fencing over boundary wall with punched tape concertina coil (PTCC) 1050 mm dia all as specified and shown on drawings and fixed with seven horizontal rows of reinforced barbed tape (RBT) as specified which is to be fixed between angle 50 mm x 50 mm x 6 mm at every interval of 3 metre centre to centre with wire, stud tied with GI staple & GI clips including all necessary bolts etc. complete all as specified and as directed. NOTE :- Cost of all items mentioned shall be deemed to be included in the quoted rate of this item except 50 mm x 50 mm x 6 mm angle iron which shall be measured and paid separately. , Dismantling of CGI/PGI sheet as in roof covering including ridge . , Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering including ridge.. , S&Fpre- painted galvalume aluminiumzinc coating GI based corrugated steel sheet 0.5 mm thick including ridge of an colour having tensile strength of 550 Mpa as in roof covering to wall fixed with self tapping screws as specified. , S&Fpre- painted galvalume aluminiumzinc coating GI based Plain steel sheet 0.5 mm thick including ridge of an colour having tensile strength of 550 Mpa as in roof covering to wall fixed with self tapping screws as specified. , Dismantling wrought iron or mild steel work in any description not otherwise provided for. , S & F rolled mild steel angle/tubular/square/rectangular roof trusses (framed), trussed purlins, rails and fastenings and heavy bracket framing, confirming to Fe 410 - W including distance pieces, cleats, etc., complete. , M & L for prepariation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer. , Removal of debris obtained from demolition/dismantling upto 5km distance to outside MD land complete all as specified and as directed , M & L for 100 mm thick plain cement concrete type C2 1:3:6 in floors and pavings as in sub-base complete all as specified and as directed. , M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in near cement slurry in floors with grey cement and pigment over 15 mm thick screed bed in CM 1:6 , M&L for providing cement concrete type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges , (i) Demolition of existing treatment of any type and preparing the surface by cleaning the concrete surface with wire brush and a high pressure water jet and ensure that it is free of dust, oil grease,loose particles vegetation roots etc including martial and labour for laying padding cement concrete in terrace 1:2:4 type B-0 (using graded stone aggregate) of 50mm average thickness maintaining 1:30 slope finishing with 10mmthick cement mortar 1:3 as specified and directed by Engr in charge. (ii) Smart Ultron Hybrid Polyurea (Slow setting) Terrace surfaces Preparation Minor cleaning work removal of loose concrete and filling cracks with polymer modified mortar using Smart care RP or Epoxy Mortar. (iii) Supplying and applying high performance polyurea elastometric waterproofing coating cold applied of spray / brush applied,Smart Care Ultron liquid membrane with an elongation of 600% and tensile strength of 12.6 N/mm2 as per ASTM D2370 crack bridging ability of 3mm as per ASTM C 1305, shore A Hardness of min 75 as per ASTM D 2240, The system includes final base preparation, epoxy primer application and applying Smart care Ultron or approved equivalent in two coats at 1.2 kg per Sqm etc, complete as per manufacture specification , Removal of vegetation plants over roof /chajjas and stone /brick masonry wall of bldg including cleaning and repair with cement concrete 1:2:4 (using 20mm aggregate ) etc as per direction of Enge-in-charge. , Cleaning and removingall soil, debris, scale and dirt, dust etcall material should be disposed off out of the defence landin covered drain width upto 1.5mtr, and depth of as per site complete all as specified and directed. . , Dismantling timber scantlings 40 sq. cm and over in section, in any position , M&L Second class hard-wood in scantlings framed and fixed clean sawn. , Materials & labour for preparation of WOODEN surfaces of any description over 10 cm width or girth and applying twocoats of synthetic enamel paint over one coat of pink primer complete. , Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm , Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding and depositing where directed at a level not exceeding 1.5m above the starting point and disposal. , S&F Steel cover grade designation HD - 20 ISI Marked (IS 12592-2002) cover of size650 x 450 (thick as per site) edge protectionof load bearing capacity of wheel load between 50 to 100 KN including handle, bar etc complete all as spd and as directed. , M & L formaking good the damaged / cracked / spalled concrete in soffits and sides of lintel beams/ Chajjas / slabs by chipping / scrubbing completely by wire brushes to make the surface rough to receive and applying two coats of epoxy based zinc rich primer master -Emaco P130 of BASF or its equivalent make on rebars @ 2.8 Kg / litre and applying solvent less epoxy resin based structural grade bonding agent on concrete surfaces and hand packing of cavities fibre reinforced thixotropic cementitious mortar including providing and fixing double scaffolding system upto G+2 bldg all as specified and as directed by Engr in Charge , M & L formaking good the damaged / cracked / spalled concrete of RCC fins / facia /parapets / similar RCC articles by Chipping / scrubbing completely by wire brushes to make the surface rough to receive and applying two coats of epoxy based zinc rich primer master -Emaco P130 of BASF or its equivalent make on rebars @ 2.8 Kg / litre and applying solvent less epoxy resin based structural grade bonding agent on concrete surfaces and hand packing of cavities fibre reinforced thixotropic cementitious mortar for any thickness to match with the existing size of fins / facia / parapet including provision of chicken mesh/steel reinforcement if necessary including providing and fixing double scaffolding system upto G+2 bldg all as spcd and as directed by Engr in Charge , Taking down shutters of steel windows any size side hung or top hung (in Ground floor if done externally and in any floor if done internally ) for repair welding the damaged portion refixing the existing hinges or fixing the new hinges (as per site requirement) dismantling and refixing by welding/rivetting, and making good the shutter in good condition without any defects in welding grinding the welded surfaces and easing the window for smooth movement complete to the satisfaction of Engr-in-Charge.(Supply of item like hinges or FI Fillets will be measured and pid separately.) , Taking down shutters of steel windows any size side hung or top hung (in First floor if done externally ) for repair welding the damaged portion refixing the existing hinges or fixing the new hinges (as per site requirement) dismantling and refixing by welding/rivetting, and making good the shutter in good condition without any defects in welding grinding the welded surfaces and easing the window for smooth movement complete to the satisfaction of Engr-in-Charge.(Supply of item like hinges or FI Fillets will be measured and pid separately.) , Taking down shutters of steel windows any size side hung or top hung (in Second floor if done externally ) for repair welding the damaged portion refixing the existing hinges or fixing the new hinges (as per site requirement) dismantling and refixing by welding/rivetting, and making good the shutter in good condition without any defects in welding grinding the welded surfaces and easing the window for smooth movement complete to the satisfaction of Engr-in-Charge.(Supply of item like hinges or FI Fillets will be measured and pid separately.) , S & F Mild steel small articles such as Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; or parts of steel windows welded plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 , Supply only mild steel box type hinges 50mm long suitable for steel windows. , Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads , S & F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane , Supply only 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane , M&L Preparation of old steel surfaces exceeding 10 cm in width of girth and treated with one coat of synthetic enamel paint complete all as specified.
