Tender For Special Repair To Bldg No. Bcd-28 And Bcd- 29 (Toilet Block) In Zone 9A At Talbehat Mil Stn
Tender Value
13.85 Lakhs
Estimated cost
Bid Submission
24 Jun 2025
0 days left
EMD
27700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
talbehat → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No. Bcd-28 And Bcd- 29 (Toilet Block) In Zone 9A At Talbehat Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster on brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 2 | M&L for Rendering 10mm thick onin CM 1:6 fair faces of brick work or concrete surfacesfair surfaces of walls finished even and smooth w/o using extra cement complete all as specified and directed. |
| 3 | M&L forRendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces of walls finished even and smooth complete all as specified and directed. |
| 4 | M&L forRendering 5mm thick in cement mortar (1:3) on fair faces of brick work or concrete surfaces as in ceiling surfaces finished even and smooth complete all as specified and directed. |
| 5 | Complete removal of existing treatment of old plastered surfaces of wall over a coat of primer on surface and applying two coats ofoil bound distemper complete all as specified and directed. |
| 6 | M&L for preparation of new plastered surfaces of wall over 1mm thick putty a coat of primer on surface and applying two coats ofoil bound distemper complete all as specified and directed. |
| 7 | M & L preparation new plastered surfaces of wallsand providing two coat of cement base paint over a coat of primer complete all as specified and directed. |
| 8 | Complete removal of existing treatment of old plastered surfaces of wallsand providing two coat of cement base paint over a coat of primer complete all as specified and directed. |
| 9 | Material and labour for preparation of newly plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed. |
| 10 | Supply only integral water proofing compound |
| 11 | Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges in large patches as in roof covering complete all as specified and as directed.Note:- opening of existing wind tie where required for taking down of AC sheet is deemed to be included in the rate quoted . |
| 12 | Dismantling of timber scantling 40 Sqcm and over in section in any position such as in rafter, purlins etc in unframed work complete all as specified and as directed |
| 13 | Dismantling of timber fillets , rails, posts, rafters, purlin etc under 40 sqcmin section, in any positionin unframed work complete all as specified and as directed. |
| 14 | M&L for reinforced cement concrete Mix Design (M-25) using 20mm graded aggregate as in slabs supported on columns and beams. |
| 15 | M&L for reinforced cement concrete Mix Design (M-25) using 20mm graded aggregate as in beams, cantilevers, bressumers, lintels over 1.5m span. |
| 16 | M&L for formwork to sides and soffits of floor or roof beam, beam hauchings, girders, bressum-mers, lintels, cantilever, shelves including supports, overhangs, etc. also splays between floors and beams, etc finished rough and flat. |
| 17 | M&L for formwork to sides and soffits of suspened slabs such as roof slabs, floor slabs, ladings and similar work, not exc. 200mm thick (horizontal or sloping) finished rough and flat. |
| 18 | S&F forTMT bars 10mm diaand over, cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed)not less than 0.90mm dia |
| 19 | Ditto- but 6mm to 8mm dia (as in stirrups). |
| 20 | Material and Labour for PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including WPC as per manufacturers instructions to achieve the slop required, with minimum thickness of 25mm consolidated and finished even and fair without using extra cement. (WPC shall be measured and paid separately |
| 21 | M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed. |
| 22 | Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed. |
| 23 | Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion orderedand directed. |
| 24 | M&L for brick work with old size sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 25 | Material & Labour for brick work with fly ash bricks built in CM 1:4, straight or curved on plan exceeding 6 M mean radius using old size bricks in half brick thick wall etc. |
| 26 | M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping and like other wk including necessary form work complete all as specified and directed by Engr-in-charge. |
| 27 | M&L PCC (1:3:6) type C-2 using 20mm graded stone aggregate 75 mm thick as in plinth protection finished fair even laid in alternatebays n.exc 2m in length all as specified and directed. |
| 28 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site spd and directed. |
| 29 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site completeall as specified and directed. |
| 30 | Supplyand fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm(moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by \"Rajshri/Echon or Eq\" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company. |
| 31 | S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately). |
| 32 | Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 33 | Supply & fixed150 mm long Extruded aluminiumalloy handles, fabricatedtype anodised complete all as specified. |
| 34 | S&F 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc. |
| 35 | S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified. |
| 36 | S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified directed by Engr-in-charge. (Jindal sec 21516,21517) |
| 37 | S&F powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified specified and directed by Engineer-in-Charge.Note:- Glass and Wiremesh paid Seprately. |
| 38 | S&F inposition 4.8mm thickfrosted glass on one side quality and glazing with glazing clips including necessary rubber packing to aluminium framen n. exc 0.5 sqm in each pane all as specified and as directed. |
| 39 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.40mm and fixed with stainless steel wire staplescompleted all as spd & directed. |
| 40 | M&L for Framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors,ladders; framed balusters; walkways; railings; framework of water tanks and similar workconforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 41 | Dismantling floor, hearth or wall tilling including cement mortar bedding, and rubbish offpremises etccomplete all as specified and directed. |
| 42 | M & L for Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate), 25 mm thick in sub base of flooring etc, complete all as specified and directed. |
| 43 | M & L for Non-skid digital coloured Ceramic tiles 7 to 8 mm thick ( square /Rectangular)area of each tile exceeding 0.11 sqmbut not exc 0.18 sqmin floors etc set and jointed in neat cement slurryand pointed inwhite cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed. |
| 44 | M&L for coloured Glazed ceramic tiles300x600 x 7mm thicktiles on walls, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tileover and including cement mortar 1:4, 10mm thick plaster complete all as spd & directed. |
| 45 | Dismantling of existing unserviceable water tank ofany description capacity exc 500 Ltr but n.exc 1000trs capacity each complete all as specified and directed |
| 46 | S& F rotational moulded synthetic (HDPE) water storage tank 1000litre capacity (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part-I complete all as spd & directed. |
| 47 | S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as spd & directed. |
| 48 | S&Fin repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked complete all as spd & directed. |
| 49 | Taking up or down steel tubing and connection 20 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed. |
| 50 | Taking up or down steel tubing and connection 20 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed. |
| 51 | S & F water tubing 20 mm bore, medium weight, ISImarked galvanized with all fittings and fixed to walls,ceiling or laid in floors complete all as specified anddirected. |
| 52 | All as per srl item above but 25 mm bore |
| 53 | Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floorsincluding taking down of old GI tubing, 40 mm bore all as specified and directed. |
| 54 | Supply & fixedPolymer coloured (Polypropeylene Delrin and ABS) low levelflushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscriptionmark with 2731 with andincluding suitable size of MS brackets, plug, screws all as required incl taking down existinghigh level/low level flushing cistern any type disconnecting pipes and jointingwith new one etcand making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed. |
| 55 | Supply and fixing in repairs Vitreous ChinaW.H.B. white oval type counter below type of size 570 x 445 mm including waste coupling, waste pipe and brackets etc. complete all as specified. |
| 56 | Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified. |
| 57 | Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) &incl 01 No ‘P’ or ‘S’ trap of dia 100mm includingprovn of lime concrete bedding, complete all as specified. |
| 58 | Supply & fixed in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified. |
| 59 | Supply andfixing in repairs, Urinal spreader of Brass chromium plated for fixing with 15 mm dia pipe., compete all as specified. |
| 60 | Supply andfixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified. |
| 61 | Supply andfixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. |
| 62 | Supply andfixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified.(Note : Weight of cock shall not be less than 0.575kg) |
| 63 | Supply & fixedin repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified. |
| 64 | S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for unionall as specified and directed by Engr-in-charge. |
| 65 | S&F in repair brass chromium plated tubular towel rail 20mm dia \"D\" type 60cm long between flanges all as specified and directed by Engr-in-charge. |
| 66 | Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified. |
| 67 | Supply & fixed in repairs stainless steel grating openable 100mm dia with hole including fixing with white cement complete all as specified. |
| 68 | Supply & fixedin repair fancy type shower rose125mm dia sizeof Rim and 30cm long CP brass pipe with swiwel joint complete all as specified. |
| 69 | S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed. |
| 70 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm diapipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed. |
| 71 | S&F looking mirror of size 600 x 450mm bevelled edgewithselected quality glass mounted on 6 mm thick AC bldg boardor commercial plywood & fixed to wooden plugs with chromium plated brass screw and cup washers.complete all as specified and directed. |
| 72 | Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., and removal complete and all as specified and directed |
| 73 | S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 74 | S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 75 | S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof fixed to pipe of bore 110mm complete all as specified. |
| 76 | S&F 110mm PVC (SWR) bends any radius |
| 77 | S&F 110mm PVC (SWR) branch piece, single (single Y) equal or unequal |
| 78 | PVC (SWR) branch piece, double (double Y) equal or unequal |
| 79 | Taking down carefully copper/Aluminium point wiring (light/fan/socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc complete all as directed. |
| 80 | Taking down carefully complete light fittings removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc complete all as directed. |
| 81 | Taking down Distribution Boards along with MCB\"s incl removing the same from site and making good to the disturbed surface complete |
| 82 | Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc complete |
| 83 | M/L for point wiring concealed type with 1.5sq mm FRLS PVC insulated unsheathed single core multistranded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl FRLS PVC rigid conduit not less than 20 mm dia with its accessories pressed steel terminal box incl 3mm thick ISI marked laminated sheet cover for fixing switches/socket/regulators and making good disturbed surfaces of wall, floors etc for the following :-Wire: Make - Finolex/V-guard/Polycab/KEI/Havells/PlazaPVC conduit: Make -Polycab/Precision/Plaza/KalingaNote:- On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit/PVC Casing capping and its accessories. |
| 84 | One light/fan/bell point controlled by one No piano type switch 5 Amps single pole one way |
| 85 | One socket outlet 5/3 pin 6 Amps controlled by one switch on the same board |
| 86 | One socket outlet 5/3 pin 6 Amps controlled by one switch on the same board. |
| 87 | All as per item NO 83 above but 3 pin socket out let 15/16 Amps on the independent Board all as spfd with single core unsheathed PVC insulated cable multistranded copper conductor of size 2.5 sq mm for phase & neutral & 2.5 sq mm for earth continuity conductor |
| 88 | S&F Switch Piano Flush button single pole one way 5/6 Amp. |
| 89 | Piano Flush button single pole one way 15/16 Amp |
| 90 | S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp, 240 volt |
| 91 | S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp and 15/16 Amp, 240 volt. |
| 92 | S&F ceiling rose surface bakelite 65mmx50mm 100watt three terminal. |
| 93 | S&F Lamp holder Batten holder PVC/Polycarbonate insulated body with metal ring and back plate for batten fitting |
| 94 | M&L concealed sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size6 sqmm (for main current) drawn in & incl PVC conduitconduit less than 20mm dia ISI markedwith all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as directed by Engineer-in-Charge PVC conduit: Make -Polycab/Precision/Plaza(i).One run of conduit two run of 6 Sqmm copper conductor & One run of 6.0 Sqmm coper conductor is measured as one unit(ii).On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit and S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete |
| 95 | S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete with top and one single pole MCB of 20 Amp 240 volt and making good to the disturbed surface completeMake:Legrand/Cchneider/Indo Asian/Siemens/Havells |
| 96 | S&F sheet metal enclosure double door for MCB DB single pole and neutral 4 way with 200 Amps, 240 volts double door (Metallic) type Make- Legrand/Hager/Schneider/ndoAsian/Siemens |
| 97 | S&F vertical sheet metal enclosure double door for MCCB DB Triple pole and neutral 4 way, (4+12) with 200 Amps rated bus bar 440 volts earth dolly IP-43, IK09, and making good to the disturbed surface complete |
| 98 | S&F MCB SP 8 to 32 Amps rating 240 volts C curve, 10 KA, 50 Hz, of poles and current carrying capacity in the MCB DB complete with connection testing and commissioning confirming to SitEC-60898-1 Make-As approved Make of DB |
| 99 | S&F MCB SPN 40 to 63 Amps rating 240 volts C curve 10 KA 50 Hz, of poles and current carrying capacity in the MCB DB complete with connection testing and commissioning confirming to IS/IEC-60898-1. Make As approved Make of DB |
| 100 | S&F MCCB 4 pole 63 Amp, 440 volt \"C\" series, 16 KA, 50 Hz, confirming to IS/IEC-60898-1 Make-As approved Make of DB |
| 101 | Supply and fixing LED 4 batten light 18/20 Watt 230 Volt, complete connection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in-Charge Make Havells/Surya/Crompton/Philips/Baial |
| 102 | Supply and fixing complete LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver, holder and LED tube light including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete Make Havells/Surya/CG/Phillips |
| 103 | Material and Labour for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground( earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all fSSR PtIincluding necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick cast RCC ( 1:2:4) type B-1 cover slab framed with 50X30X4 mm MS angle (reinforced with 6 mm dia defomed bar @ 15 cm CIC both ways and suitable handle of 10 mm dia round bar) including providing horenal or coke and magnesium sulphate in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade) wire mesh conner luas. complete in all respect., GI earth wire protected by 15 mm bore (light grade) galvanized iron pipe and other end connected to the earth bar (test point) made of MS flat (40OX32X6 mm) bend in D shape and fixed to wall by means of fast nut or bolt grouted in to wall at 1 mntr from plinth height. 4sgmm PVC insulated (colour green) copper conductor single run as earth continuity conductor along with 15 mm PVC conduit grouted in wall or fixed on wall surface to be continued up to main switch board and fix with common earth dolly as directed by EIC. Disposal of soil to a distance not exceeding 50 mtr and necessary A/U 5 Each as shown in electrical plate e testing on completion complete all as specified and as directed. 23.00 Supply and fixing in repair of wooden doors with hinges and paint with colour as existing on Meter box/ DB Each Job Box complete all as specified and directed. 24.00 Supply and fixing LED Inverter Lamp Make : Shakti Cat Part No -SZBLB22009 - iBB 9W B22 or equivalent complete all as specified and directed. Make: Havells/ Philips/Surya /Crompton/Halonix/ Shakti 25.00 Supply and foxing Inverter Batten T/L fiting Make: Shakti Cat Part No - SZSLBMX018-iBB 18W 4 ft or equivalent complete all as specified and directed. Make: Havells/ Philips/Surya /Crompton/Halonix/ Shakti |
| 104 | Supply and foing in repair of wooden doors with hinges and paint with colour as existing on Meter box DB Bos complete af as specified and directed |
| 105 | Supply and fixing LED Inverter Lamp Make Shakti Cat Part No-SZBLB22009-BB 9W B22 or equivalent and directed: Maka: Havelis/ Philips/Surya/Crompton/lalonix/ Shakt complete all as specified and |
| 106 | Supply and fang Inverter Batten T/L fitting Make Shakti Cat Part No SZSLBMX018-1BB 18V 4 It or equivalent complete all as specified and directed Make: Havells/ Philips/Surya/Crompton/Halonix/Shakti |
| 107 | Note :-Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.) |
AI Tender Summary
Tender Timeline
Jun 16, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedJun 24, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 26, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender