Bids Are Invited For Screw Flight For Screw Conveyor Of Butt Shot Blasting M/C In Rodding Shop-I As Per Dwg. No.Rod/Sp/Mech/A2/4692, Sh-2/2 ,Punch Assembly For Thimble Removal Press As Per Drawing No:Rs-I/Sp/M/A2/1625,Rev.01 Material: En 24, Anugul-Odisha

Bids Are Invited For SCREW FLIGHT FOR SCREW CONVEYOR OF BUTT SHOT BLASTING M/C IN RODDING SHOP-I AS PER DWG. NO.ROD/SP/MECH/A2/4692, SH-2/2 ,PUNCH ASSEMBLY FOR THIMBLE REMOVAL PRESS AS PER DRAWING NO:RS-I/SP/M/A2/1625,REV.01 MATERIAL: EN 24 3 22920010000 4 EA GUIDE ROLLER ASSEMBLY WITH BEARING FOR LIFT TABLE OF H/UH M/C AS PER DRAWING NO.C/SP/MECH/A1/1373,REV-01, ITEM NO.1 TO 7. NOTE: THE BEARING TO BE USED IS TAPER ROLLER BEARING NO.30216A OF SKF/FAG MAKE ONLY 4 22960154160 8 EA BUSH(SPACER) FOR FIXING STUD ASSEMBLY AS PER ITEM NO.3, DRAWING NO: ROD/SP/MECH/A3/4191,REV-01. 5 22972010560 4 EA DRIVE ROLLER-1 AS PER DWG NO. RS-1/MECH/SPR/A1/11851, REV.01 FOR MATING STATION ROLLER CONVEYOR OF CASTING ZONE IN RODDING SHOP-1. NOTE : 1) THE ROLLER SHALL BE MADE OUT OF SEAMLESS TUBE OF SPECIFIED DIMENSION AS MENTIONED IN THE DRAWING ITSELF. 2) THE SPROCKET TO BE USED IN THE ROLLER SHALL BE OF REPUTED MAKE LIKE ROLCON/REYNOLD/TIDC/SJ PATEL/GALAXY ONLY 6 22972010570 4 EA DRIVE ROLLER-2 AS PER DWG NO. RS-1/MECH/SPR/A1/11851 REV01. FOR INLET ROLLER CONVEYOR AND LOWERING TABLE ROLLER CONVEYOR OF CASTING ZONE IN RODDING SHOP-1 NOTE : 1) THE ROLLER SHALL BE MADE OUT OF SEAMLESS TUBE OF SPECIFIED DIMENSION AS MENTIONED IN THE DRAWING ITSELF. 2) THE SPROCKET TO BE USED IN THE ROLLER SHALL BE OF REPUTED MAKE LIKE ROLCON/REYNOLD/TIDC/SJ PATEL/GALAXY ONLY. 7 22972070180 10 EA COVER TRAY FOR PAWL BAR OF RODDING BENCH CASTING MACHINE IN RS-1 AS PER DRAWING NO. RSI/MECH/SPR/A2/11065,Rev-1 ITEM NO.1 TO 4 8 23010011340 12 EA DOOR HOUSING AND MODIFIED AXLE ASSEMBLY FOR H/UH MACHINE OF RODDING SHOP-2 AS PER DRAWING NO. RSII/MECH/SPR/A2/11095. 9 23010018120 2 EA DRIVE SHAFT D.90 X L595 LT DRIVE WHEEL OF HOOKING / UNHOOKING M/C RS-II AS PER ITEM NO-11, DWGRS-II/MECH/SPR/A2/11596,SH-2/4 10 23010018130 2 EA NON DRIVE SHAFT D.90 X L.353 LT IDLE WHEEL OF HOOKING / UNHOOKING M/C RS-II AS PER ITEM NO-12, DWG-RSII/MECH/SPR/A2/11596, SH-3/4 11 23014402810 15 EA PIN BUSH ASSEMBLY FOR TILTING CYLINDER OF BATH FINISHING MACHINE-1(OLD) OF RODDING SHOP-2 AS PER DRAWING NO. RS2/MECH/SPR/A3/15242. 12 23015102220 80 NO BUCKET FOR BUTT SHOT BLASTING M/C IN RODDING SHOPII AS PER DRG NO.RSII/MECH/SPR/A3/10112. 13 23016100120 4 EA TOP FLANGE SUPPORT FOR PUNCH CYLINDER OF THIMBLE PRESS IN RODDING SHOP-2 AS PER DRAWING NO.RSII/MECH/SPR/A3/10833, HOWEVER THE MOC SHALL BE EN8 INSTEAD OF EN9 IN THE DRAWING. NOTE: i. THE RAW MATERIAL OF FLANGE SUPPORT SHALL BE ULTRASONIC TESTED BEFORE MANUFACTURING.THE TEST REPORT OF ABSENCE OF VOID AND DEFECTS SHALL BE SUBMITTED. ii. MATERIAL TEST CERTIFICATE FROM ANY GOVT APPROVED LAB. WRT EN8 SHALL BE SUBMITTED ALONG WITH DESPATCHED DOCUMENT 14 23020101110 2 EA DRIVE SHAFT FOR LONG TRAVEL OF MATING MACHINE IN RODDING SHOP-II AS PER DRG. NO. RSII/MECH/SPR/A2/11602,(SH.5/5),item no.20.NOTE:- ITEM SHOULD BE PROVIDED WITH ANTIRUST COATING AND WRAPPED WITH POLYTHENE. 15 23024201030 4 EA BEAM GUIDE ROLLER PIN D.25XL.113 AS PER ITEM NO-1, DWG-RS-II/MECH/SPR/A2/11602, SH1/5

Refer document

Refer document

Refer document