|
| 1 | Boring, providing and installing Bored cast-in-situ reinforced cement Concrete pile of specified diametre and length below the pile cap in cement concrete 1 :1.5:3 ( 1 cement, 1 .5 Coarse M Sand,& 3 graded stone aggregate of 20 mm nominal size) to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including Bentonite solution machinery charges labour chargres etc., |
| 2 | Earth work excavation in all classes of soils such as hard stiff clay, stiff black cotton, hard red earth, shales, murram, ordinary earth, earth mix with 50% fair sized boulders etc., with initial lead and lifts including laying, spreading, leveling, sectioning breaking clods etc., includingall incidental charges etc., complete as per standard specification . for FoundationsSS 20B TNDSS NO. 23 &24 V, VI (S2) VI 9 |
| 3 | Supply filling of Stone Dust in layer of not more than 15 cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyence of sand to Site and all labour charges and all other incidential charges etc,. complete as per Standard Specification TNDSS NO. 24 &25 NBC Part VI (S2) 8 |
| 4 | Plain Cement concrete of mix 1:4:8 (One cement four M-sand and eight aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including labour charges, transporting and placing in position including shoring, strutting forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification.TNDSS NO.28 V,VI S25 |
| 5 | Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc., ). TNDSS NO.86 K, 86 A |
| 6 | Without Strutting |
| 7 | With Strutting |
| 8 | Reinforced Cement Concrete 1:1½:3 Mix (One part cement, one and half part sand and three part of aggregate)using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc.Complete with std.Specifications. TNDSS NO: 30 V, VI (S3), VII-3. |
| 9 | Supplying, fabricating and placing in position mild steel or ribbed tor steel for all reinforced cement concrete works as per design given including cost of steel and binding wire with all conveyance and lead charges in all floors etc.complete complyingwith standard specifications and as directed by the deparmental engineers. TNBP No:30.- |
| 10 | Brick Work in CM 1:5 (One part of cement & five parts of M - sand) mix using Third Class Country Brick Kiln Burnt bricks 8 ¾ \" x 4 ¼ \" x 2 ¾\" including cost and conveyance of materialsto work site and including all labour charges for mixing, laying, curing the concrete etc., complete as per standard specifications and as directed by departmental Engineers –TNBP No:31 |
| 11 | Plastering with CM 1:5(One part of cement & five parts of P - sand) mix for 12mm thick including cost and conveyance of all materialsto work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:56&57 |
| 12 | Special Ceiling Plastering with CM 1:3 (One part of cement & three parts of P -sand)mix for 10mm thick including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:30,56&57 |
| 13 | Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of\"approved quality and colour over a priming coat, including thoroughscraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A |
| 14 | Paving the flooring with ceramic tiles of following types of approved colour and qualitylaid in cement mortar 1:3 (one cement and three M -sand ) 20mm thick in all floors and the top pointed with the same coloured cement etc., complete in all floors. |
| 15 | Dadoing walls with the following types tiles of suitable size of approved quality and colour set in cement mortar 1:2 (one cement ,two P -sand); 10mm and pointing with colour cement neatly etc., complete in all floors. |
| 16 | Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being \"32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers.etc., complete.-1 m 3 |
| 17 | Finishing the top of roof with one course of machine pressedtiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete |
| 18 | Supplying and fixing in Position of Indian Oriya pan type water closet with “P’’ or “S’’ trap to set inbrick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage etc. complete. |
| 19 | Supplying and fixing in position best Indian make white glazed earthenware WASH HAND BASIN of 560x406mm with a a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waster water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specifications. |
| 20 | Supplying and fixing in position of Indian make White glazed earthen ware Flat Back Urinal of approved quality including dismantling masonry if necessary and redoing the same to original condition etc., complete as directed by the departmental officers. |
| 21 | UPVC DoorSpecification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Doors of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window.The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work(PWD SOR 2020-2021, P.No 71, SI.No 247) |
| 22 | Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works) |
| 23 | Supplying and fixing in position GI unions of heavy duty of approved quality and good variety of various sizes inluding necessary cutting and threading of GI pipes for jointing the union and providing two coats of painting with good variety and approved quality of synthetic enamel paint over one coat of primer in case of pipe line above ground level / one coat of tar in case of below ground level for both internal and external water supply arrangements, etc., complete complying with standard specifications.(The GI unions should be got approved by Executive Engineer before use on works). |
| 24 | Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications.The PVC pipes shall be got approved by Executive Engineer before use on works. |
| 25 | 20mm PVC pipe |
| 26 | 110mm PVC pipe |
| 27 | Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc., |
| 28 | Supply and fixing of TNEB Board suitable for 3 Phases 63A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2\" x 1 1/2\" x 1/4\" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 63A fuse units(500V) 1 No. Neutral link, copper earth flat of size 1\" x 1/4\" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete.SD 131 |
| 29 | Wiring with 2 x 1.5 sqmm (22/0.3) PVC insulatedunshealhed SC.Cu.conductor of1100V grade in suitable PVC rigid Pipe on wall and ceiling with PVC accessorieswith TW switch box with 5A F.T. switch inflush with wall, coveredwith hylum sheet of 3mm thick with painting of suitable colour for open PVClight/fan point(For Electronic regulator) (5 pointsper coil). SD 22 |
| 30 | Wiring with 2 x 1.5 sqmm (22/0.3) PVC insulated single core unshealhed copper conductor cable of 1100V grade in suitable heavygauge MS conduit pipeonwall and ceiling with M.S. accessories inflush with wall with 150mm x 100 mm x 75mm MS switchbox with 3mm thick hylum sheet cover for 5A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed plug point. SD 12 |
| 31 | Supply and fixing of fancy glass shade and 11W CFLfor BH Point. SD-80 |
| 32 | Supplying and fixing PVC rain water down fall pipes of 4kgf/cm2 variety of the following sizes excluding cost of PVC specials but including charges for fixing them in position with nessary shoes, bends, clamps, TWplugs, screws, nails etc., complete. |
