|
| 1 | Repairs/Renovation of Passage at PV Section for Creation of GeM Room at MPF Ambernath |
| 2 | Taking Down Chowkhats or frames of any description exc.1.5 sq. m but n exc 4 sq. m each along with shutter and removing to store etc all complete as directed by the Engg in Charge. |
| 3 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. all complete as directed by the Engg in Charge. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc. all complete as directed by the Engg in Charge. |
| 5 | Demolition of Unreinforced Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including site clearance & removal of rubbish outside of Factory Premises etc. all complete as directed by the Engg in Charge. |
| 6 | Dismantling of brick work or stone boulder masonry built in cement mortar, complete cleaning of site & removal of rubbish off the factory premises etc all complete as directed by the Engg in Charge. |
| 7 | M&L Rendering 20 mm thick cement plaster in CM 1:4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing including neeru finish to plastered surface etc all complete as directed by the Engg in Charge.Note: The Contractor shall use aggregate of proper gradation for mortar preparation. Use of stone dust for mortarpreparation is not permitted |
| 8 | M & L for Granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc all complete as directed by the Engg in Charge.Note: Sample of Granite shall be got approved from the Competent Factory Authority before commencement of works. |
| 9 | Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc all complete as directed by the Engg in Charge. |
| 10 | M&L for Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) Avg 70 mm thick in sub base flooring including proper leveling of surface to receive tiles etc all complete as directed by the Engg in Charge. |
| 11 | M&L for Screed bed or bedding layer of mortar Avg 25 mm thickin cementmortar 1:6 for laying floor finishes etc all complete as directed by the Engg in Charge. |
| 12 | S&F Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sq.m in floors (Make: HR Johnson, Kajaria, Somany, RAK Ceramics) set and jointed in neat cement slurry and pointed in white or coloured cement to matchetc all complete as directed by the Engg in Charge.Note: Sample of Tiles shall be got approved from the Competent Authority before start of work. |
| 13 | S & F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc all complete as directed by the Engg in Charge. |
| 14 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, etc all complete as directed by Engg-in-Charge.Note: Sample of Aluminium Framing shall be got approved from the Competent Authority before fixing. |
| 15 | S&F sheet Glass 4 mm thick (Make Modi Guard / Saint Gobain) plain or tinted as per requirement of site etc all complete as directed by Engg-in-Charge. Note: Sample of glass shall be got approved from the Competent Authority before fixing. |
| 16 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified of approved design & quality etc all complete as directed by the Engg in Charge.S & F anodised aluminium snap grid framework for false ceiling of approved design & quality etc all complete as directed by the Engg in Charge.Note: Sample of all material shall be got approved from EIC before use in work. |
| 17 | S & F anodized aluminium snap grid framework for false ceiling of approved design & quality etc all complete as directed by the Engg in Charge.Note: Sample of all material shall be got approved from EIC before use in work. |
| 18 | S & F Non asbestos fibre cement building boards (Minimum 4 mm thick of reputed make as approved by the Engg in Charge) fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping etc all complete as directed by the Engg in Charge.Note: Sample of Non Asbestos building board shall be got approved from the Competent Authority before fixing. |
| 19 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 etc all complete as directed by the Engg in Charge. |
| 20 | M & L for cement concrete in lintels etc. Type B0 1:2:4, 12.5 mm graded aggregate including use of formworketc all complete as directed by the Engg in Charge |
| 21 | S & F TMT Bars 10 mm dia & over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc all complete as directed by the Engg in Charge |
| 22 | S & F Plain, solid, straight chowkats of First class hardwood and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed etc all complete as directed by the Engg in Charge |
| 23 | S & F Flush shutters 40 mm thick, solid core construction, with particle board core and plywood face panels, commercial type on both sides & both sides covered with decorativeface veneer, lipping frame to match, cutting of door to required shape to accommodate viewing pane with proper beading etc all complete as directed by the Engg in Charge.Note: Sample of door & veneer shall be got approved from the Competent Authority before fixing. |
| 24 | Cutting holes in brick walls in cement mortar for inserting holdfasts exc 1 brick but n.exc 2 bricks and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 etc all complete as directed by the Engg in Charge. |
| 25 | S&F Butt hinges 125 mm, cast brass, cromium plated etc all complete as directed by the Engg in Charge.Note: Sample of hinges shall be got approved from the EIC before fixing. |
| 26 | S&F Extruded brass handles Minimum 150 mm size, fabricated type, polished or cromium plated etc all complete as directed by the Engg in Charge.Note: Sample of handles shall be got approved from the EIC before fixing. |
| 27 | S&F brass, barrel tower bolts 200 mm cromium plated with barrel of extruded section and fixed etc all complete as directed by the Engg in Charge.Note: Sample of tower bolts shall be got approved from the EIC before fixing. |
| 28 | S&F Brass, sliding door bolt 300 mm cromium plated with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed etc all complete as directed by the Engg in Charge.Note: Sample of sliding door bolts shall be got approved from the EIC before fixing. |
| 29 | M & L for application of 3 mm thick wall care putty (Make: 1st Quality from Asian Paints/Birla/JK) on wall surface etc all complete as directed by the Engg in Charge. |
| 30 | M & L for preparation of surfaces of any description including complete removal of old paint if any by thorough scrapping, priming coat & application of plastic emulsion paint in two coats (Make: 1st Quality from, Asian, Nerolac, Berger, Birla Opus) for walls & ceiling etc all complete as directed by the Engg in ChargeNote: Sample & shade of paint shall be got approved from the Competent Authority before starting of work. |
| 31 | Supply and installation of 4 mm ACP (Aluminum Composite Panel) sheetincluding all necessary materials such as the ACP sheet, SS screws, and any other components required, to cover DB\"s & for other aesthetic works as per the instructions of the Engineer-in-Charge (EIC) |
| 32 | Design supply & installation of suspended Spider glazing system designed to withstand the wind pressure as per IS 875(Part II) .The Suspended system held with Spider fittings of SS316 grade steel of approved manufacturer with glass panel having 12mm thick clear toughened glass hold together with SS 316 grade stainless steel Spider and bolt assembly with laminated glass fin 21 mm thick. The glass fins and glass panel assembly shall be connected to slab/ beams by means of SS316 grade stainless steel brackets and anchor bolts, non staining weather sealants of approved make, Teflon/nylon bushes and separator to prevent bi-metallic contact, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion and seismic movement etc. The joints between glass panels (6 to 8mm) and gaps at their perimeter and in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof and dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixtures nut bolt, washer, buffer plates, fasteners, anchor, SS Channel laminated glass etc. all completed for the purpose of payment, actual elevation area of glazing including thickness of joints and portion of glass panel inside the SS channel shall be measured etc all completed as directed by Engg-in-Charge. Note: Sample of all materials and fixtures / fittings shall be got approved from EIC before use in work. |
| 33 | Supply & Fixing of Modular Type switches 1 way, 6A (Make:Anchor/ Roma/GM/Cona/Legrand) etc all complete as directed by the Engg in Charge.Note: Sample of switches shall be got approved from the Competent Authority before starting of work. |
| 34 | Supply & Fixing of moduler Socket 6A, 2/3 Pin (Make: Anchor/Roma/GM/Cona/Legrand) etc all complete as directed by the Engg in Charge.Note: Sample of socket shall be got approved from the Competent Authority before starting of work. |
| 35 | S & F Wiring for Circuit / Submain wiring along with earth wire with 2 x 2.5 sq.mm+ 1 x 2.5Sq.mm earth wire of FR PVC insulated copper conductor(Make:Finolex / Polycab / Havells ) in PVC conduit (Make: Precision / Pressfit) etc all complete as directed by the Engg in Charge. |
| 36 | S & F One Light Point or one Fan point controlled by one switch with cables 1.5 Sq.mm Size copper multistrand wire, (Make: Polycab/ Finnolex/KEI/RR)in PVC Casing n Caping of thickness 2 mm, (Make:Pressfit/Prestige)etc all complete as directed by the Engg in Charge. |
| 37 | Supply and Fixing of MODULAR METAL/PVC FLUSH BOX 6 Module, (Make: Havells/ Pressfit/ Legrand/GM) etc all complete as directed by the Engg in Charge. |
| 38 | Supply and Fixing of MODULAR WHITE COVER PLATE WITH FRAME 6 Module (Make: Havells/ Pressfit/ Legrand/GM) etc all complete as directed by the Engg in Charge.Note: Sample of Cover plate & ancillary material shall be got approved from the Competent Authority before starting of work. |
| 39 | S & F of Ceiling Rose 6A, 3 Point (Make:Anchor/Roma/GM/Legrand)etc all complete as directed by the Engg in Charge.Note: Sample of Ceiling rose & ancillary material shall be got approved from the Competent Authority before starting of work. |
| 40 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator remote and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) (Make:Crompton/Bajaj/Automberg) etc all complete as directed by the Engg in Charge.Note: Sample of Ceiling Fan & ancillary material shall be got approved from the Competent Authority before starting of work. |
| 41 | Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. (Make:Havells/Bajaj/Syska/Philips /Crompton) etc. all complete as directed by the Engg in Charge.Note: Sample of all materials shall be got approved from EIC before use in work |
| 42 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth etc all complete as directed by the Engg in Charge. |
| 43 | Supplying & installing perforated painted with powder coating MS Cable trays of apporx size750 mm x 75 mm depth x 2 mm thicknesswith perforation not more than 17.5% in convenient sections, joined with connectors, suspended from the ceiling with MS suspenders including bolts & nuts and painting suspenders etc as required etc all complete as directed by the Engg in Charge. Note: Sample of tray shall be got approved from the EIC before start of work. |
| 44 | Supply and install hi wall split AC units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2.of capacity 1.5 TR of (Make: LG/Voltas/Bluestar) etc all complete as directed by the Engg in Charge.Note: Sample of AC & ancillary materials shall be got approved from EIC before use in work. |
| 45 | Supply and fixing of Modular Switch Socket, 6/16 A - 2/3 pin combined 3 module, (make Legrand/Anchor/Crabtree) all complete as directed by the Engg in Charge.Note: Sample of all materials shall be got approved from EIC before use in work. |
| 46 | S & F of exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers etc all complete as directed by the Engg in Charge.Note: Sample of exhaust fan & all ancillary materials shall be got approved from EIC before use in work. |
