Tender For Place Making Work From Naja Market Novelty Square To Municipal Corporation Office In Hazratganj - Dismantling Work 2 Demolishing Cement Concrete Manually/ By Mechanical Means Including Disposal Of Material Within 50 Metres Lead As Per Directi, lucknow-Uttar Pradesh

Tender For Place making work from Naja Market Novelty Square to Municipal Corporation office in Hazratganj - DISMANTLING WORK 2 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 3 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix) 4 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (in cement mortar) 5 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. 6 Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (BITUMINOUS ROAD) 7 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 8 Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. 9 Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge 10 CIVIL WORK 11 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil 12 Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in-charge. 13 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 14 Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc for mass concrete 15 Providing & Laying Designer Pavers 100mm x 100mm with thickness ranging from 70-90mm of approved shape and complete as per direction of Engineer-in- Charge. including transport ,loading ,unloading and conveyance of material from available source to work site, including labour charges for fixing and pointing etc., complete 16 Sand FillingFilling in foundation trenches as per drawing and technical specifications clause 305.3.9 17 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) 18 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 19 Cement mortar 1:3 (1 cement :3 coarse sand) 20 12 mm cement plaster of mix : 21 1:4 (1 cement: 4 coarse sand) 22 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete. 23 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 24 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer 25 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand): 25mm thick 26 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 27 Supply and installation of 60 L: AUX Waste Bin of material Stainless Style with Contemporary Mounting: Root fixed, Surface/baseplate fixed, wall/post mounted with Features: Ashtray, complete with foundation as per the direction of the Engineer in charge 28 Providing and laying drain gratings on both sides of the road anlong with tree grating wherever required. 29 Drain Grating - FRP GRATING (DRAIN)SIZE: 366 x 1001 x 30 H MMTHICKNESS: 6/7 MM 30 Tree Grating - SIZE: 800 x 800 x 400 (Inner Dia’) MMTHICKNESS: 30 MM 31 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Size of Tile 600 x 1200 mm 32 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 33 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia 34 Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications 35 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 36 Centering and shuttering including strutting, propping etc. and removal of form for : Walls 37 Steel in kg 38 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. 39 For vertical surface two coats @ 0.70 kg per sqm per coat 40 For horizontal surface one coat @1.10 kg per sqm. 41 Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineerin-charge and panelling with panels of : (Note:- Butt hinges and necessary screws shall be paid separately). 12 mm thick one side Pre-laminated particle board (decorative lamination on oneside and other sides balancing lamination) grade -1, medium density flat pressed,three layer particle board FPT - I or graded wood particle board FPT-1 conformingto IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 andpre-laminated conforming to IS : 12823, Grade -1, Type II marked 42 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 450 mm dia 43 Boaring/ drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS : 2800 part I, including collecting sample from different starta, preparing and submitting equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer In charge, up to 150 meter depth below ground level. 300 mm diaAll type of soil (DAR 23.2.1.1 based)Sanction Rate 44 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia 45 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia having minimum wall thickness5.40 mm 46 Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm in the recharge pit, over the existing layer of boulders, in required thickness for all leads & lifts all complete as per direction of Engineer in charge. DAR 23.6 47 brick ballast 40 mm class 150 48 brick ballast 40 mm class 150 49 Providing & fixing sand stone Single piece ornamental bench of approved design pattern (1200x450x450MM) and specifications including, all materials, labour and T & Petc. required for proper completion of work as directed by engineer - in -charge 50 Supply and fixing of Bollard made from mid steel with CNC machine finishingwith 140mm outer diameter , thickness of 3mm r and 1100mm Height . Expose height 900mm from above Ground level and fixed the remaining 200mm below the GL. three number of circular rib of R06mm radius are provided at the top . The whole product is power coated black colour as per standard recommendation of Engineer. For fixing the Bollards with M10 cement concrete footing of minimum dimension 20cmx20cmx20cm,with base plate, anchor rods complete. 51 Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. 52 Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applyingHeat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee Support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. 53 Mandatory/ Regulatory sign boards of 900 mm diametrewith support length of 3750 mm 54 Providing and fixing StandAlone Signage in Marble of approved thickness with powder coated 10-12mm MS letters and illustration at desired locations with letters (in english, hindi and Braille)- etched, through cut, infilled or painted, also including the cost of design, fabrication and onsite installation with all the necessary accessories and equipments for fixing on any surface as per drawing and design approved from Architect in charge English: Helvetica Font with min. 36 size Hindi: Krutidev Fontwith min. 36 size, PSR 55 Signage-A Informative Signage of Sandstone/Marble of size (1200x2100)MMvisibly from both side, PSR 56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab except colour of Black, Cherry/Ruby Red or equivalent 57 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent 58 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 59 Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. 60 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 61 Supplying, fixing and commissioning of Hydraulic (Retractable) Bollards as per specification 62 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. 63 Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 64 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 65 Labour rate for the mentioned item. Supply & fixing of 6 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm thikness with Double arm bracket 1 Mtr length in 1:2:4 RCC foundationbolt including the cost of foundation, excavation & back filling and Required T&P completee in all respect. 66 Providing & fixing ofConcrete Drain Covers Sandstone Colour550X750X50MM Colour: Sandstone Ultra High Performance Pigmented Concrete With Steel Fiber Reinforcement Load Capacity Suitable for 10 Tonne Pigmented Concrete Bayferrox Lanxess Fe203 Colour Index 77491.0000etc all complete in direction of engineer in charge 67 Providing & fixing of Concrete drain cover Concrete Drain Covers Sandstone Colour 550X750X50MM Ultra High Performance Pigmented Concrete With Steel Fiber Reinforcement Load Capacity Suitable for 40 Tonne Vehicle Passing Bayferrox Lanxess Fe203 Colour Index 77491.0000 etc all complete in direction of engineer in charge 68 Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fastenersat both ends. The work shall be executed as perdrawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job.The barricading shall not be removed without prior approval of Engineerin- Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work). 69 PLUMBING OF AREA- HAZRATGANJ NAJA MARKET ROAD, PLAZA, CHAURAHA, TRILOKNATH ROAD , CAPPER ROAD, DR. SOUJA ROAD, DAYNIDHAN ROAD - PLACEMAKING AND REDEVELOPMENT 70 SANITARY FIXTURES & ACCESSORIES 71 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. 72 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White 73 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require 74 White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap 75 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. 76 32 mm dia (for wash basin) 77 Providing & Fixing 600 X 450 mm bevelled edge mirror of superiorglass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 78 Providing & fixingtoilet paper holder. C.P. Brass 79 WATER SUPPLY PIPES AND FITTINGS 80 Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. 81 Internal work exposed on wall 82 40mm nominal outer dia pipes 83 50mm nominal outer dia pipes 84 Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 85 Concealed work including cutting chase and making good the wall etc. 86 15mm nominal outer dia pipes 87 20mm nominal outer dia pipes 88 25mm nominal outer dia pipes 89 32mm nominal outer dia pipes 90 Providing & fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) 91 40 mm nominal bore 92 50 mm nominal bore 93 Providing&fixing15 mm nominal bore45 cm long unplasticised PVC connection pipewith brass unions.45 cm length: 15mm nominal bore 94 Providing & fixing 15 mm nominal bore CP brass bib cockof approved quality conformingtoIS 8931. 95 Providing and fixing 15 mm nominal bore C.P brass long nose bib cock of approved qualityconforming to IS standardsandweighing notlessthan 810 gms. 96 Providing & fixing 15 mm nominal bore C.P. brassstop cock (concealed)of standard designandof approvedmakeconforming to IS : 8931. 97 Providing & fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points of approved quality conformingto IS8931. 98 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of three urinal basins with 10litre white P.V.C. automatic flushing cistern 99 Constructing brick masonry chamber 300 x 300x500mm, insidewithF.P.S. brick work in cement mortar 1: 4 (1 cement : 4 coarse sand) for StopCock, withC. I. surface box 100 x 100 x 75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4mix (1cement : 2 coarse sand:4 grade stone aggregate 20mm nominal size); necessary excavation, foundationconcrete 1:5:10 (1 cement :5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar1 : 3 (1 cement : 3 coarse sand )12mmthick finished with a floatingcoatof neat cementcomplete as per standard design 100 Providing and fixing square mouthS. W. Gully trapgrade `A complete with C.I. gratingbrickmasonry chamber with F.P.S bricks and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 101 150 x 100 mm. size P type 102 Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 103 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. 104 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 105 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. 106 PN - 10 Pipe, 50 mm OD (SDR-11) 107 PN - 10 Pipe, 75 mm OD (SDR-11) 108 PN - 10 Pipe, 110 mm OD (SDR-11) 109 TOTAL ( SCHEDULED ITEM ) 110 PART B(NON SCHEDULED ITEMS - AS PER MARKET RATES) 111 SUPPLYOFSANITARY FIXTURES, ACCESSORIESANDBATHROOMFITTINGS 112 Providing & fixing of white vitreous china urinal partition for half stall urinals. (Jaquar or equivalent) 113 Providing & fixing UPVC Floor trap of self cleansing designwith CP Jalicomplete in all respects. (Make : Supreme / Finolex / Prince) 114 P-Trap type Floor Trap 110 x 75 mm 115 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. 116 Providing & fixing 50 mm. dia. G.I elbow (drain point) in the toilet floor including50 mm dia. C.P. waste jali complete as required. 117 C. INTERNAL ELECTRICAL WORKS -HAZRATGANJ NAJA MARKET ROAD, PLAZA, CHAURAHA, TRILOKNATH ROAD , CAPPER ROAD, DR. SOUJA ROAD, DAYNIDHAN ROAD - PLACEMAKING AND REDEVELOPMENT 118 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 119 Group A 120 Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed steel conduit as required 121 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 122 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 123 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 124 2 X 16 sq. mm + 1 X 6 sq. mm earth wire 125 Supply and drawing co-axal TV cable RG-6 Grade, 07 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PCV sheath in the axisting surface/recessed steel/PVC conduite as required. 126 1 Pair, 0.5mm dia annealed copper conductor, FRLS PVC insulated, unarmoured, Telephone cable 127 Supplying and fixing following Suitable size GI Box with Moudular plate and cover infront on surface or recess, including providing and fixing 2 nos 3 pin 5/6 A moduler socket outlet and 2 nos. 5/6 A moduler switch, connection etc. as required. ( for light pluges to be used in non residentions, painting etc. as required. 128 Supplying and fixing following Suitable size GI Box with Moudular plat and cover infront on surface or recess, including providing and fixing 25 A moduler socket outlet and 25 A moduler SP MCB C Curve including connections, painting etc. as required. 129 Supplying and fixing PVC batten/ angle holder including connections etc as required. 130 Supply and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 131 5/6 A Switch 132 2 way 5/6 A switch 133 Telephone socket outlet 134 TV Antenna socket outlet 135 Bell Push 136 Supplying and fixing following size/ modules, GI box along withmodular base & cover plate for modular switches in recess etc as required. 137 1 or 2 Module (75mmX75mm) 138 3 Module 100mmX75mm) 139 4 Module 125mmX75mm) 140 6 Module 200mmX75mm) 141 8 Module 125mmX125mm) 142 12 Module 200mmX150mm) 143 Supplying and fixing following modular base & cover plate on existing moduler metal boxes etc. as required. 144 1 or 2 Module 145 3 Module 146 4 Module 147 6 Module 148 8 Module 149 12 Module 150 Supplying and fixing of following sizes of pvc conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 151 25mm 152 32mm 153 Supply, installation, testing and commissioning of 1200mm sweep, BEE 5 Star rated, ceiling fan with brush less direct current (BLDC) Motor, class of insulation: B, 3 nos. Blades 30cm long down rod, 2 nos, canopies shackle kit, safety rope, copper winding, power factor not less than 0.9 service value (CM/M/W) Minimum 6.00, air delivery minimus 210 cm/min 350 rpm (tolerance as per IS:374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washer, temperaure rise = 75Degree C (max.), insulation resistance more than 2 mega ohm, Suitable for 230 V, 50Hz single phase AC supply, earthing etc. Complete as required. 154 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as 155 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. asrequired. 156 Supply and fixing call bell/Buzzer suitable for single phase,230V, Complete as required. 157 Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. 158 Supplying and fixing following way, Horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator) 159 4 way(4+12) , Double door 160 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 161 16 way , Double door 162 Supply andfixing following rating, double pole, 240 V isolator in the existing MCB DB complete with connection, testing and commissioning etc. as required. 163 40 A 164 Supply andfixing following rating, four pole, 415 V isolator in the existing MCB DB complete with connection, testing and commissioning etc. as required. 165 63 A 166 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 167 Single Pole 168 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 169 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe et 170 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as 171 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 172 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 173 PART B - NON - SCHEDULED ITEMS (AS PER MARKET RATES ) 174 Supply & erection of AC 230/250 volts 50 hz Exhaust fans including provding nut bolts mounting frame and other accessories including connection etc complete as required as per direction of E /I make:- Havells / Cromption / USHA 175 300 mm Sweep 900 RPM 176 Supply & fixing of following white RJ 45 cat 6 data outlet / information outlet ETL verified to meet exceed TIA / ETA 177 Supply & fixing of following Telephone outlet 178 Supply & installation of CCTV / Suvillance system. (Honeywell 20 channel NVR full HD IP based- 01 nos, IP Honeywell dome camera 2MP with night vision- 8 nos., IP Honeywell 2 MP HD Bullet camera with night vision- 8 nos.) 179 Supply of LED Tube Light with batten suitable for up to 1X22 watt LED tube light fitting complete, including tube on surface complete in all respect. 180 1 X 22 W 181 Supply ofrecess/Surface/Pendent mounting round 12 watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set complete in all respects. (Make: Wipro) 182 LED Fancy Gate Light, Aluminium, 12 W 183 Earth work in excavation bymechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.All kinds of soil 184 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5kmalso includingrammingandwateringoftheearthinlayersnot exceeding20cmintrenches,plinth,sidesoffoundationetc.complete. 185 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 186 Providingandlayinginpositioncementconcreteofspecified grade excluding the cost of centering and shuttering - All work uptoplinthlevel:1:3:6(1Cement:3coarsesand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) 187 Brick work with common burnt clay F.P.S. (non modular) bricks of class -150 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) 188 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in- charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mixor bear the cost of extra cement. M-25 Grade Concrete 189 SteelreinforcementforR.C.C.workincludingstraightening, cutting,bending,placinginpositionandbindingallcomplete Thermo-Mechanically Treated bars of grade Fe-500D or more 190 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) 191 Providingandapplyingwhitecementbasedputtyofaverage thickness1 mm, of approved brandand manufacturer,over the plasteredwallsurfacetopreparethesurfaceevenandsmooth 192 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied@ 2.20kg/10 sqm 193 ProvidingandlayingfactorymadechamferededgeCement Concretepaverblocksin footpath, parks,lawns, driveways or light trafficparking etc,of requiredstrength, thickness& size/ shape, made by table vibratory method using PU mould, laid in requiredcolour&patternover50mmthickcompactedbedof sand, compacting and proper embedding/laying of inter locking paverblocksintothesandbeddinglayerthroughvibratory compactionby usingplatevibrator,fillingthe jointswithsand andcuttingofpaverblocksasperrequiredsizeandpattern, finishing and sweeping extra sand. complete all as per directionof Engineer-in-Charge. 194 60mm thick cement concrete paver block of M-35 gradewith approved colour, design & pattern (Square and Rectangular shape) 195 80mmthickC.C.paverblockofM-35gradewithapproved color design and pattern.(Square and Rectangular shape) 196 Providing and laying matt finished vitrified tile of size 100x100x16mmhavingwaterabsorptionlessthan0.5%and conformingtoIS:15622ofapprovedmakeinallcoloursand shadesinoutdoorfloorssuchasfootpath,courtyardmulti modelsetc.,laidon20mmthickbaseofcementmortar1:4 (1cement:4coarsesand)inallshapes&patternsincluding groutingthejointswithwhitecementmixedwithmatching pigments etc. complete as direction of Engineer-in-Charge. 197 Providingandlayinginpositonreadymixedorsitebatched design mix cement concrete for reinforcedcement concrete work; using coarse aggregate and aggregate derived from natural sources,PortlandPozzolana/OrdinaryPortland/PortlandSlag cement,admixtures in recommended proportons as per IS:9103 to accelerate / retard sieving of concrete, to improve durability and workabilitywithoutimpairingstrength;includingpumpingof concretetositeoflaying,curing,carriageforallleads;but excludingthecostofcentering,shufering,fnishing andreinforcementasperdirectonoftheengineer-in-charge;for the following grades of concrete.Note: Extra cement up to 10% of the minimumspecified cement content in design mix shall be payableseparately.Incasethecementcontentindesignmix ismore than 110% of the specified minimum cementcontent, the contractor shall have discreton to eitherre-design the mix or bear the costofextracementConcreteofM25gradewithminimum cement contentof 330 kg /cumOne CubicMetreConcrete of M30 grade with minimum cement contentof 350 kg /cumOne CubicMetreConcrete of M35 grade with minimum cement contentof370kg/cumOneCubicMetreConcreteofM40grade with minimum cement contentof 390 kg /cumOne CubicMetreConcrete of M50 198 Concrete of M30 grade with minimum cement contentof 350 kg 199 Applying stamping finsh of the top surface of freshlylaid plain / reinforced cement concrete of specifedgrade in portco, side walks, drive ways, pool decks andopen yard as per directon of the Engineer-in-Charge.* The concrete shall be placed and screened to thefnished grade and •oated to the uniform surface byusing standard fnishing techniques. approved colorhardener @2.7 kg/sqm shall be applied evenly to thesurface of the fresh concrete by the dry shake methodby sprinkling in twoor more shakes foated aer eachshake and trowel only after final coating. The approved released agent @ 0.113 Kg/Sqm shall be applied evenly to the trowelled surface before stamping or the said release agent can be applied to the fexiblepolyurethene stamp moulds of approved design and inrequired sizes to achieve fnal stamping pattern. These stampings shall be placed on the surface of concrete in three to four pieces at a time and tapped gently with rammers of sufcient size and weight to leave properstamp marks and the process repeated for the remaining concrete surface till the whole surface to bestamped is completed within the time while the concrete is in plastic stage of setting.After stamping, the curing shall be done as permanufacturers specifcatons. After inital curing theimprinted joints shall be grouted using cement slurrymixed with color hardener as per the requirement. Thesurface shall be sealed by applying acrylic based sealernot less than 0.167 litre/Sqm on fnished surf The constructon joints shall be provided by grovecutting of size 4 mm x 20 mm in panel size 3 m x 3 m orlesser as per the site conditons and flling the samewith 10 mm baker rod and providing & laying (PU)Polyurethane based joint sealer of approved make asper manufacturer’s specifcatons and fnished byapplying polyurethene resin based topprotectve clearcoat of minimum 80 micron applied with rollers onproperly cured and dry clean surface. (The cost ofconcrete for flooring is not included in the item, whichshall be paid for seperately).One SquareMetreSupplying and laying of Uni-Axial Woven PolysterGeogrid conforming to MORTH 3100 and IRC113, as soilreinforcement/basal reinforcement includingaccessories like te-strips, nuts & bolts and loops/lugsfor joining reinforcing elements with the facia pannels,overlaps and other protectve elements for synthetcgeo-grids and all other actvites required for reinforcedsoil walls, slopes etc complete as per designrequirements, manufacturer specifcatons and as perdirecton of engineer-in- charge.Uni Axial Woven polyster geogrid of minimum tensilestrength 40KN/m in the Longitudinal directon and 20KN/m in the Transverse directon.One SquareMetre 200 62mmthickcementconcreteflooringwithconcretehardener topping,underlayer50mmthickcementconcrete1:2:4(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)andtoplayer12mmthickcementhardenerconsistingof mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’sspecifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. 201 Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. 202 Supplying & Laying of Precast Saucer Drain 150 thick 300 mm wideinluding sand bed etc all complete in direction of engineer in charge 203 Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 204 Providing, laying and making kerbchannel 30cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the topsmoothetc.completeandasperdirectionofEngineer-in- 205 Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and fillingwith150mmthickjamunasand,includingspreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge. 206 Providing andfixing10x10x10cmGranitestoneblockhandcut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mmwidefilledwithsamemortarincludingruledpointingetc. complete as per direction of engineer-in-charge. 207 Providing and laying Polished Granite stone flooring in required design and patterns,inlinearas wellas curvilinearportionsof the building all complete as per the architectural drawings with 18mmthickstoneslabover20mm(average)thickbaseof cementmortar1:4(1cement:4coarsesand)laidandjointed with cement slurry and pointing with white cement slurry admixedwithpigmentofmatchingshadeincludingrubbing, curingandpolishingetc. all completeas specified andas directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent 208 ProvidingandlayingflamedfinishGranitestoneflooringin requireddesignandpatterns,inlinearaswellascurvilinear portionsofthebuildingallcompleteasperthearchitectural drawingswith18mmthickstoneslabover20mm(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointedwith cementslurry and pointing withwhite cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and asdirectedbytheEngineer-in-Charge:Flamedfinishgranite stoneslabJetBlack,CherryRed,EliteBrown,CatEyeor equivalent 209 Painting runway/taxi track/apron marking with adequatenos of coats to give uniform finish with road marking paint of superior makeasapprovedbytheEngineer-in-charge,i/ccleaningthe surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete.New work (Two or more coats) 210 Layingoldcementcocreteinterlockingpaverblocksofany design/shapelaidin requiredline,level,curvature,colourand pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer in-charge. (Old CC paver blocksshall be supplied by the department free of cost). 211 Layingatorneargroundleveloldkerbstonesofalltypesin positiontotherequiredline,levelandcurvature,jointedwith cement mortar 1:3 (1 cement : 3 coarse sand), including making jointswithorwithoutgrooves(thicknessofjoints,exceptat sharpcurve,shallnotbemorethan5mm),includingmaking drainage opening wherever required etc. complete as per direction of Engineer-in-charge. (Length of finished kerb edging shallbemeasuredforpayment).(Oldkerbstonesshallbe supplied by the department free of cost) 212 Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fastenersat both ends. The work shall be executed as perdrawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job.The barricading shall not be removed without prior approval of Engineerin- Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work). 213 Centeringandshutteringincludingstrutting,proppingetc.andremoval of form for 214 Walls(anythickness)includingattachedpilasters,butteresses,plinth and string courses etc. 215 Providing&fixingofcementconcreteBollardsM-30GradeR.C.C.150mmdiaincludinggoutinginfoundation750mm height including all necessary T&P etc all complete in directio of 216 Repairing of Existing Canopy including PPGL Sheet & necessarymember &Screw,nut, bolts,washer ,including paintingpolishingetcallcompleteindirectionofengineerin charge. 217 Boring/drillingborewellofrequireddia for casing/ strainer pipe, by suitable methodprescribedinIS:2800(partI), including collecting samples from different strata, preparing and submitting stratachart/borelog,includinghire& running charges of all equipments, tools, plants&machineriesrequiredforthe job, all complete as per direction of Engineer-in-charge,upto90metredepth below ground level. 218 300 mm dia 219 Supplying, assembling, lowering and fixinginverticalpositioninborewell, unplasticizedPVCmediumwellcasing (CM) pipe of required dia, conforming to IS:12818,includingrequiredhireand labourcharges,fittings&accessories etc.allcomplete,foralldepths,asper direction of Engineer -in-charge. 220 150 mm nominal size dia 221 Supplying, assembling, lowering and fixinginverticalpositioninborewell unplasticizedPVCmediumwellscreen (RMS) pipes with ribs, conforming to IS: 12818, includinghire & labour charges, fittings&accessoriesetc.allcomplete, for all depths, as per direction ofEngineer-in-charge. 222 150 mm nominal size dia 223 Gravelpackingintubewellconstruction inaccordancewithIS:4097,including providing gravel fine/ medium/ coarse, in requiredgrading&sizesasperactual requirement,allcompleteasper direction of Engineer-in-charge. 224 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit) 225 withrequiredcapacityaircompressor, running the compressor for required timetill wellis fullydeveloped, measuringyieldofwellby“V”notch methodorany otherapprovedmethod, measuring static level & draw down etc. bystepdrawdownmethod,collecting water samples & getting tested in approvedlaboratory,i/cdisinfectionof tubewell,allcomplete,includinghire& labourchargesofaircompressor,tools & accessories etc., all as per requirement and direction of Engineer-incharge. 226 Providingandfixingsuitablesize threadedmildsteelcaporspotwelded platetothetopofborewellhousing/ casing pipe, removable as per requirement, all complete for borewell of 227 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm 228 ProvidingandfixingBailplug/Bottom plug of required dia to the bottom of pipe assemblyoftubewellasperIS:2800 (part I). 150 mm dia. 229 Supplyofsubmersiblepumpofmake KSB / Crompton / kirloskar 7.5HP with control panel, support wire etc. 230 Supply and laying of aluminium conductorPVCinsulatedarmoured served sheathed cables 1100 Volts grade ata depth of 750 mm below groundleveloveracushionof75mm. thick sand all around and protectedwithburntbricksonsidesandontop. Onsurfacethecablerunshallbe fixed onM.S.clampsetc.ofsuitablesizeor asdirectedbytheEngineer-Incharge, complete in allrespect. The armouring of the cable shallbeproperly connectedwiththe earthonductor by clamps etc.submersibble cable from pump panel to 231 Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc. 32 mm dia nominal bore 232 Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) 233 Supply of 100mm dia Johnson screen. 234 Providing and stacking of Nyctanthes arbor- tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer- 235 Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. 236 Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of 237 Providing and stacking of Ficus panda of height 90-105cm.with10-12branchesandhealthy foliage,wellformedincementpotsofsize30 cm as per direction of the officer-in-charge.. 238 Providing and stacking of Ficus reginald well branched, bushy of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer- 239 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushtyshape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. 240 Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. 241 Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size ofPoly bags & as per direction of the officer-in- 242 Providing and stacking of Asparagus sprengeri of height 15 cm to 20 cm, full of leafy branches in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.. 243 Providing and stacking of Ophiopogon jaburan ( variegated ), full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge. 244 Providing and displaying of Croton Petra Bangalore variety having ht. 60 cm to 75 cm with 4 to 6 branches, well developed, fresh and healthy colorful leaves in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer- 245 Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed withrivetscompleteinallrespectsincluding painting inside and outside of tree guard with: Two or more coats of synthetic enamel paint of approved quality shade over a priming coat 246 Trenching in ordinary soil up to required depth includingremovalandstackingofserviceable materials and then disposing of as directed and spreading earth & neatly levelling, breaking clodsetc.andmakingthetrenchedareawith designedmounds,pathsandsittingspacesetc. toproperlevelsbyfillingwithearthorearth mixed with manure and properly watering completeworkinrequiredtopographyasperdrawing & specifications. 247 Supplyingandstackingofgoodearthatsite includingroyaltybutincludingcarriage 20 km (earthmeasusredinstackswillbereducedby 248 Supplyingandstackingatsitedumpmanure from approved source,including carriage up to 1 km (manure measured in stacks will be reduced by8% for payment) 249 Mixing earth and manure in specified proportion or as directed. 250 Roughdressingthetrenchedgroundincluding breaking the clods. 251 Fine dressing the ground 252 Spreadingof mixedgoodearthandmanurein specifiedproportionsasaboveandinrequired thickness. 253 Providing&layingSelectionno.1grassturf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothenandlightwateringthesame,asperdirection of officer in charge 254 Preparation of mounds of various size and shape by available excavated / supplied earth in layers notexceeding20cmindepth,breakingclods, wateringofeachlayer,dressing etc.,leadupto 50meterandliftupto1.5mcompleteasper direction of Officer-in-charge. 255 Excavating,supplying andfilling oflocal earth (including royalty) by mechanical transport upto a lead of 5km alsoincluding rammingand watering of the earth in layers not exceeding 20 cm in trenches, plinth, 256 Providing & Laying reinforced cement concrete pipe NP3 for Planter 600mm height and 300 mm depth in ground including excavation, protection work, backfilling, concrete and masonary works all complete in direction of engineer in charge. 257 Fabrication , supply and installation of Stainless steel 304 grade canopy around the existing tree guard with laser cut SS -304 grade fins with satin finish and 10mm thick polycarbonate multiwall sheet on roof from sabic plastic products or equivalent complete in all respect along with it aluminum fittings . SS-304 grade tree grate with laser cut design cutout patterns for waterpenetration will be fixed at the center and 18mm thick gang saw cut mirror polished granite/wood plastic composite wooden planks will be fixed ontop of the existing masionary in a curve shape 258 Cement Concrete Planter 259 D & E .( HORTICULTURE AND EXTERNAL ELECTRICAL WORK)-HAZRATGANJ NAJA MARKET ROAD, PLAZA, CHAURAHA, TRILOKNATH ROAD , CAPPER ROAD, DR. SOUJA ROAD, DAYNIDHAN ROAD - PLACEMAKING AND REDEVELOPMENT BILL OF QUANTITY 260 Part G (Horticulture Work) 261 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 262 Supplying and stacking of good earth at site including royalty and carriage upto 20 km lead complete (earth measured in stacks will be reduced by 20% for payment). Analysed Rate. 263 Extra For levelling and neatly dressing of disposed soil completely as per the engineer in charge DSR2023; 2.36 264 Supply and laying of bi axial extruded high modulus polypropylene geo grid conforming to MORTH specifications for base/sub base reinforcement having minimum tensile strength 40 Kn.m IN THE LONGITUDNAL AND TRANSEVERSE DIRESTION, WITH 14 Kn/ M AND 28 Kn/M AND 28 Kn/M TENSILE STRENTGH at 2% and 5 % strain respectively in the longitudnal and transverse direstion, junction eficiency not less than 95% and with 38 mmx 38 mm mesh opening psrLDA Approved 265 Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).DSR Horticulture 2020; 2.25 266 Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge DSR Horticulture 2020; 2.9 267 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).DSR Horticulture 2020; 2.8 268 Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, byspreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).DSR Horticulture 2020; 2.1 269 Rough dressing the trenched ground including breaking clods.DSR Horticulture 2020; 2.6 270 Fine dressing of the ground., DSR Horticulture 2020; 2.7 271 Providing & laying Selection no. 1 doob grass turf with earth 50mm to60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge DSR Horticulture 2020; 2.34 272 Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately): In rows 5 cm apart in both directions DSR Horticulture 2020/ 2.10.1 273 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 60 cm dia, and 60 cm deep. DSR Horticulture 2020; 2.14.4 274 Holes 45 cm dia, and 45 cm deep., DSR Horticulture 2020; 2.14.5 275 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal ofunserveiceable material’s as per direction of officer in charge (excludingcast of plant & water). DSR Horticulture 2020; 2.57 276 Trees Plant, 2.57.1 277 Shrubs Plant, 2.57.2 278 Hedge Plant, 2.57.3 279 Providing and stacking of Clerodendrum inerme having ht. 25 cm to 30 cm multi branched in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge., DSR Horticulture 2020; 6.7 280 Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge., DSR Horticulture 2020; 5.3 281 Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge., DSR Horticulture 2020; 8.30 282 Providing and stacking Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. DSR Horticulture 2020; 9.8 283 Providing and stacking of Belamcanda chinensis of height 45-60 cm. branched in earthen pots of size 20 cm as per direction of the officer-in-charge. (Lepord lily), PSR LALBATTI 284 Providing and Displaying of Spathiphyllum (peace lily), having 15 cm to 25 cm ht. blooming stag with fresh & healthy foliage well developed in 15 cmof Earthen pot/plastic pot as per direction of officer-in-charge. DSR Horticulture 2020; 3.90 285 Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliagein Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge., DSR Horticulture 2020; 6.25 286 Shrubs/TREE Plant 287 Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge.(DAR 2020 Hort - 8.32) based 288 Providing and stacking of Ficus panda of height 90-105 cm. with 10-12branches and healthy foliage, well formed in cement pots of size 30 cm asper direction of the officer-in-charge. (DAR 2020 Hort - 8.28) based 289 Trees Plant 290 Providing and stacking of Jacaranda mimosifolia of height 10-12 feetin big poly bags of size 18 as per direction of the officer-in-charge.PSR 291 Providing and stacking of Butea frondosa (Flame of Forest) healthy and multi branches of height 4-6 feet in big poly bags of size 18 as per direction of the officer-in-charge.PSR 292 Providing and stacking of Lagerstroemia Flaush (jarool) healthy and multi branches of ht.10-12 feet in Earthen pots of size 12 as per direction of the officer-in-charge. PSR 293 Providing and stacking of Tabebiua (Dolne smith) healthy and multi branches of ht.12-14 feet in Earthen pots of size 18 as per direction of the officer-in-charge. PSR 294 Providing and stacking of Terminalia Mentali healthy and multi branches of height 10-12. in big polybags of size 18 as per direction of the officer-in-charge. PSR 295 Providing and stacking of Plumeria alba healthy and multi branches of height 10-12 feet in big poly bags of size 18 as per direction of the officer-in-charge.PSR 296 Providing and stacking Nicodia of height6-8 feet with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.PSR 297 Providing and stacking Cassia Gluca of height 8-10 feetwith bushy healthy plant in 14 bags & as per direction of the officer-in-charge. PSR 298 Providing and displaying of Phoenix palm plant, having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.PSR 299 Supply and installation ofBamboo of Height 10-12 feet. In all work complete. Market RatePSR 300 (Irrigation) 301 Trenching and Back Filling. Sanctioned Rate. 302 Supply, Installation, laying & commissioning of 90 mm outer dia 6Kg/cm2 HDPE pipe. 33.01 (Jal Nigam Varanasi SOR) 303 Supply, Installation, laying & commissioning of 63 mm outer dia 6Kg/cm2 HDPE pipe. 33.01 (Jal Nigam Varanasi SOR) 304 Supply, Installation, laying & commissioning of HDPE Flange with tail piece, packing & nut bolt complete in all respect. Sanctioned rate 305 Supply, Installation, laying & commissioning Of reducer 90 mm to 63 mm outer dia 6Kg/cm2 HDPE pipe. Sanctioned rate 306 Supply, Installation, laying & commissioning Of ELBOW JOINT 90 DEGREE FOR 90 mm HDPE pipe. Sanctioned rate 307 Supply, Installation, laying & commissioning Of ELBOW JOINT 90 DEGREE FOR 63 mm HDPE pipe. Sanctioned rate 308 Supply, Installation, laying & commissioning Of TEE JOINT90 DEGREE FOR 90 mm HDPE pipe. Sanctioned rate 309 Supply, Installation, laying & commissioning Of TEE JOINT90 DEGREE FOR 63 mm HDPE pipe. Sanctioned rate 310 Supply, Installation, laying & commissioning Offor 63 mm TAIL PIECES. Market Rate 311 Supply, Installation, laying & commissioning of for 90 mm TAIL PIECES HDPE PIPES. Market Rate 312 Supply, Installation, laying & commissioning Of PRESSURE Gauge 2.5 size (Gyceryne). Market Rate 313 3 disc filter. Market Rate 314 2 disc filter. Market Rate 315 Thermos Temperature Controller wuth switch and socket .2 mm cable. Market Rate 316 Butt velding electric heating plate. Market Rate 317 3 CIbutterfly valve. Market Rate 318 2 CIbutterfly valve. Market Rate 319 SPRINKLERS 320 Supply, Installation, laying & commissioning of Service Saddle 3 inch x 1.25 inch. Sanctioned rate with bush 321 Supply, Installation, laying & commissioning of Service Saddle 2 inch x 1.25 inch. Sanctioned rate with bush 322 Supply, Installation, laying & commissioning of Swing Joint for 10 - 12 meter range 360 degree popup. Market Rate 323 Supply, Installation, laying & commissioning of Swing Joint for 3 - 4 meter range 360 degree popup. Market Rate 324 Supply, Installation, laying & commissioning of 25 mm outer dia 6Kg/cm2 CPVC pipe. Market Rate 325 Supply, Installation, laying & commissioning Of Ball Valve for 25 mm pipes. Market Rate 326 Supply, Installation & commissioning of pop sprinkler plastic make material with 3 - 4 meter range 360 degreesMR 327 Supply, Installation & commissioning of pop sprinkler plastic make material with 10- 12meter range 360 degrees. Market Rate 328 Engagement of Plumber for required work etc all complete as per direction of Engineer in charge. PWD SOR 2020-21/Labour Rates Chapter.Rs. 420.00+10%CP 329 Engagement of Labour for required work etc all complete as per direction of Engineer in charge. PWD SOR 2020-21/Labour Rates Chapter.Rs. 335.00+10%CP 330 4 - BORING 331 Boaring/ drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS : 2800 part I, including collecting sample from different starta, preparing and submitting equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer In charge, up to 150 meter depth below ground level. 300 mm diaAll type of soil (DAR 23.2.1.1 based)Sanction Rate 332 Supply, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS: 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer in charge. 200 mm nominal size diaDAR No. 23.3.3 333 Supply, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer in charge. 200 mm nominal size diaDAR No. 23.10.3 334 Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm in the recharge pit, over the existing layer of boulders, in required thickness for all leads & lifts all complete as per direction of Engineer in charge. DAR 23.6 335 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe, removable as per requirement, all complete for bore well of: 200 mm dia. DAR No. 23.13.3 336 Providing & Fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS 2800 part - 1 including necessary bolts & nuts of required size complete. 200 mm clamp. DAR No. 23.14.3 337 Supply and fixing of pump set & composite electric panel for submersible kirloskar/ sons/ crompton openwell pumpset greeves make three phases 380-440 v 50 cycles supply with fountain bolts and 3 core 2.5 mm flat PVC flexible copper conductor double insulated submersible cable and 4 core 1.5 mm form fountain pool to fountain electric panel etc fountain pool to fountain electric panel etc. complete with internal wiring lighting system. 338 7.5 HP pump 339 Electric Panel Box 340 Supply and fixing of 3 HP single phase open well submersible pump set of 50 mm x 50 mm pipe size complete with all material, labour T&P etc all as per direction of Engineer in charge. (make kirloskar/ crompton/ KSB 341 Supply and fixing of 2.5 sqmm 3 core PVC insulated PVC shethed flate submersible cable pump with bare bunched copper conductor for submersible pump motor with 1100 volt grade ISI marked all complete as per direction of Engineer in charge.Sanctioned Rate 342 Arrangement of Plumber for 1 year maintenance. PWD SOR 2020-21 343 Horticulture Maintenance 24 months 344 Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Play grounds / Public parks Per Sqm (as per yard stick 1Mali =2.00Acre).DSR (Hort) 2020/2.40.5 345 Cutting of Hedge/Edge including removing of cut material, cleaning, hoeing of hedge/ edge bed watering, manureing & apply insecticides & fungicides etc. (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.DSR20202.2.36 346 Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 05 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment). DSR 2020 horti - 2.25 347 Supplying and stacking of good earth at site including royalty and carriage upto 15 km complete (earth measured in stacks will be reduced by 20% for payment). Analysed Rate. 348 Supply & stacking Urea 40% Nitrogen @160 kg per acre (as per yard stick of CPWD LDA SOR 2018-19/11.1 349 Supply & stacking DAP 50 kg per acre/year. LDA SOR 2018-19/11.2 350 Supply & Stacking Bone Meal/ Oil Cake(LDA SOR Horti 2018-19/11.3) 50 kg per acre/Year 351 Removal of garden waste by TATA 407 or equivalent including loading and unloading and carriage upto 1 km lead, complete disposal upto designated place as per direction of Officer in charge. DSR Horticulture 2020/2.60 based (Analysis Rate attached) 352 Part H (Electrical) 353 PART (X) 354 FOUNTAIN 355 SITC of Spray comprises of a Calyx Aerating in center flanked with Foam Jets on 4 corners of waterbody.Manifold/Pipework are made from Galvanised steel, B-class, make Jindal, ISI Mark with necessary accessories like flanges, sockets, stands etc. made of steel- galvanized. High quality rubber gaskets, nuts & bolts along with gunmetal control valves to adjust flow pressure.Proper completion of workAs per direction of E/IcFOR A 6 METER DIA WATERBODYPSR (36/G20/CE/23) 356 SITC of In Calyx Aerating Spray, water is sprayed in an inverted cone pattern withasmallcenterjet.Calyxnozzlemadeofaluminiumalloy– epoxycoated/StainlessSteel,centerjetnozzlemadeofbrass– chromeplated.Approx.heightofwatereffects:Calyx–1.25m heightX4.5mdia,CenterJet–3mheight. Proper completion of workAs per direction of E/Ic,FOR A 6 METER DIA WATERBODYPSR (36/G20/CE/23) 357 SITC of Foam jet nozzle, on ball joint, of1.25” orifice size. Nozzle made ofBrass- Chrome plated. Approx. height of water effects: 1.2m. Proper completion of workAs per direction of E/Ic, FOR A 6 METER DIA WATERBODYPSR (36/G20/CE/23) 358 Supply,Installation,TestingandCommissioningofLuminaries comprise of 12V LED lights (RGB). Complete light body made of Stainless steel 304 grade, total 27watt power leds. Toughened glass with seal.Stainless steel 304 grade cable gland. All external nuts and bolts are of Stainless steel 304 grade. Adjustable mounting bracket is made of Stainless steel 304 grade. IP 68 compliant. All in pool connections shall be fully waterproof. Make of Luminaries As per direction of E/Ic,FOR A 6 METER DIA WATERBODYPSR 359 SITCofMonoblocktypesubmersiblepumpset whit stainer/ filter ofFollowing Capacity(Threephase,50Hz,415-380VAC)propercompletion ofworkasperdirectionofE/Ic. Kirloskar/Crompton Greaves/KSB/Texmo. Suction filter for pump: Filter body & filter mesh made from AISI 304 standard stainless steel. As per direction of E/Ic 360 3 HP PSR 361 SITC of 1.1 kV grade double insulated copper flexible cable 2.5 sq.mm x 3 core for pumps,As per direction of E/IcPSR 362 SITC of 1.1 kV grade double insulated copper flexible cable 1.5 sq.mm x 4 core for lights, As per direction of E/Ic PSR 363 PSR Supply, Installation, Testing and commissioning of specialised Outdoor type Electric panel for fountain which include control arrangement for fountain, pumpset andRGB Sequencing lighting comprises of :1. Contactor 25 Amp- 01 Nos (Make: L&T/ Schneider/ Siemens/ GE)2. DOL Starter - 01 Nos (Make: L&T/ Schneider/ Siemens/ GE)3. Single Phase Preventer- 01 Nos (Make: Bentex/ Selec/ GIC or equivalent)4. Incomer Main Switch 20 Amp- 01 Nos (Make: L&T/ Schneider/ Siemens/ GE)5. Overload Relay 6-12 Amp- 01 Nos (Make: L&T/ Schneider/ ABB/ BCH or equivalent)6. Fuse for motor 32 Amp- 03 Nos (Make: GE/ L&T or equivalent)7. MCB for Lights 6 Amp -01 Nos (Plaza/ Anchor/ ABB/ Havells/ Legrand or equivalent)8. Push Button On/ Off switches (Red/ Green)- 02 Nos. 9. Overload Indicator - 01 Nos (Make: Eaton/ Siemen or equivalent)10. Single Phase Indicator- 01 Nos (Make: Eaton/ Siemen or equivalent)11. 3 Phase indicator RGB- 01 Nos (Make: Eaton/ Siemen or equivalent)12.Voltmeter- 01 Nos. (Make: Motwane, Innova, Fluke or equivalent)13. Ampere Meter- 01 Nos (Make: Motwane, Innova, Fluke or equivalent)14. SMPS/ Transformer for lights- 01 Nos (Make: Meanwell/ Pheonix/ Omron or equivalent)15. RGB Lights controller- 01 Nos. (Make: Wet Design/Fontana/A.M. Irrigation System/Bharat engineers)16. Internal Wiringsteel sheet 16 gauge paint finish enclosure with hinged front door with provision for incoming & outgoing cable entry. Outgoing ampere 10, size of panel - 3ft X 2ft X 1ft depth.As per direction of E/Ic PSR (36/G20/CE/23) 364 Supply of 4000mm Extruded Square aluminum pole (grade 6063) Sq. 150 x 3mm thickness with IP68 Connector.Bespoke laser cutting design of length 1400mm with 50W In-Built LED with controlled downward light emission options (customized) with SS fasteners, Pre treated epdm black gaskets. Die-cast aluminum mounting plate Sq.250 x 12mm thick with 4 elongated holes 38 x 19 to suit M16 bolts at PCD 180 with pure polyester powder coating. Fixed with Hot dip galvanized foundation bolt. Mechanical resistance should be minimum IK06. The Pole should be undergone pure polyester powder coating process & Acid treatment to ensure high corrosion resistance. On the top of the pole there will be built-in Spot Lights of 2 x 18W LED are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Inbuilt Surge protection 6KV. Optical grade clear toughened glass diffuser of 4mm thickness with controlled downward light emission. Colour Temperature LED 3000K, 230-240Vac, CRI >80, MacAdam step 3. The driver should be inbuilt in the pole itself and maintenance can be done from the junction box itself. PDC aluminum service door 348mm height x 110mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable,6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. Any other internal cables and connections shall not be covered in the scope of supply. The manufacturer should have Inhouse NABL accredited lab to check and provide correct photometry of the product. The make should be as per K-Lite Verbena Spot KL-4583/Wipro/Ligman 365 Supply and fixing of 3500mmsteel poles are made out of mild steel galvanized rebbed extrusion profile having bottom section dia125mm and upper section dia 81mm with cast iron embellishment e8The pole have a service window at bottom section wih heavy duty four way connector and a mcb. Mild steal base plate with four nos. mounting holes is fixed and welded with bottom section . pole is primer coated and polyurethene painted . POLES BPTH SIDE OF THE ROADS AT 10 METER CC DISTANCE. PSR - BEGUM HAZRAT MAHAL PARK 366 Supply and fixing of OVER 600mm long aluminium dia cast body post top is mounted at the top with polycarbonate diffuser and fitted with 40w led disc bis registered make philips , bajaj, twinkle, lustore, K LITEor equivalent repuateted make Quotation rates 367 S/E of G.I. wire on 8 to 4 SWG on pole/service bracket including binding etc. complete in all respects SI.No. 628/18. 368 S/W of submain with two Nos. of 2.5 Sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material Labour and T&P required for proper completion of the work as directed at site by E/I. SI. No. 289/18. 369 S/Fof40ATPNofAutomaticstreetlightcubiclecontrolpanelpaintedwithanti corrosivealkaliandacidproofpaintconsistingoftimeswitchTSO100serieswith contractors,HRCfuses,isolatingswitchmeteringinstrument& instrumentbox with CTs etc, in case of TPN, complete in all respect as per direction of Engineer-in-charge. SI. No. 807/18 e(ii). 370 S/L of following cable Al conductor P.V.C. insulated armoured served sheathed cable 1100V grade at a depth of 750mm. Below ground level over a cushion of 75mm with DWC Pipeapproved makeUPPPCL as per direction of E/I. complete in all respects. 501/2018. Approved Makes:- Gloster/ Polycab/ KEI/ SCI/ Havells PWD SOR 501 371 10 sq. mm 4 core 372 (a) 35 Sq.mm 3.5Core 373 (b) 16 Sq.mm 4 Core 374 (c) 70 Sq.mm 3.5 core 375 S/F of following size palm or pin type copper tin plated cable socket (Lug) to the cable leadinsulatingwithtapeandmakingconnectionscompleteinallrespectsasper direction of E/I.SI.No.504/SOR-18. 376 10 sq. mm 4 core 377 (a) 25 sq.mm. 378 (b) 50 sq.mm 379 (c) 16 sq.mm 380 S/B of earth rod 20mm dia into 2.5mtr long including G.I. wire 7/16 SWG to connect earth rod to earth clamp on pole 3.00 mtr long steel conduit to carry earth wire along the pole. A.R. Bond No.87/CE/EE(E/M)2021, Dated 09-11-2021 381 S/Fof6Ampto32Amp.SPMCB(10KA)Ccurvecompleteinallrespectasper direction of Engineer-in-charge. SI No. 1002/18. CAT-A. 382 Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountendon non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc.The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. ( Incoming 200 Amp. TPN-1 No Outgoing 100 Amp. TNP-2 Nos. Cat. B. Cubicle TypePWD SI No : 802 (a) 383 Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swgand inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. PWD SI No :725 (A) 384 Supply and Laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. DSR E&M 2022/14.161 385 Supply, Installation, testing & commissioning of Servo Stabilizerwith Isolation transformer 100KVA,3-phase servo voltage stabilizer with isolation transformer , oil cooled, Input 300-470 VAC, 4 Wire, 50 Hz, output: 400+/-1% with oil,suitable for UNBALANCED LOAD with automatic operation (outdoor type-IP 64).The stabilizer shall comply with the following requirement:: Regulation : +/- 10 %.: Over load & Short circuit protection.: Protection cut-off against Over/Under Voltage.: Single phase protection.: 3 nos. phase indication lamps. 386 PLINTH AREA RATES CPWD 2023, Supply installation , testing and commissioning of IP based CCTV system for building security comprising of PTZ/FIXED CAMERA, CABLING , RECORDING , DISPLAY SYSTEM HARDWARE SOFTWARE SUPPORT,FOR EXTERNAL SURVILLANCE 6.10.2 , FOR PLAZA AREA ONLY 387 Operation and maintenance for 1 years 388 PART (Y) 389 LFkkfir dh x;h ykbZVksa ds vuqj{k.k ,oa lapkyu dk dk;ZA 390 Providing of Trained Electricion With Tool Kit (As per PWD SOR/2020-202. For 18 months after DLP 391 Providing ofHelper Technicion (As per PWD SOR/2020-2021.For 18 months after DLP 392 PART-Z 393 H.T./L.T. work 394 S/Fofdoublepolestructurewith2nosS.T.poleforS/S 410SP-55 11 Mtr. longin1:3:6CC foundation 1/6 of pole length below G.I. and 30cm above G.I. 20cm thick around the pole with 2 nos. channel 125mmx75 mm one No. Chennel cross arm of 75mmX 40mm 2 No. 50X50X6mm sngle iron bracings with necessary nut bolts & packing pieces complete with painting as per direction of E/I.(PSR Bond No. 490/CE/2024) 395 S/F of 11 KV Pin insulator with G.I. Bolt /spindle nut etc. complete in all respects. (PSR Bond No. 490/CE/2024) 396 S/Fof11KVDiscinsulatorincludinggunfittingoncrossarm/clampsfixedonpole complete in all respects. (PSR Bond No. 490/CE/2024) 397 S/E of over head line with A.C.S.R. conductor on pole/service bracket including binding etc. complete in all respects. S.I.No-627/18. Racoon/Dog(PSR Bond No. 490/CE/2024) 398 S/F of M.S. Channel 75mmX40mm Vshape crossd arm for two No. pin insulator proper completion of work. (PSR Bond No. 490/CE/2024) 399 S/E of 11 K.V L.A. set of 3 wire. suitable for mounting on steel support complete in all respect as perdirection of E/I.(PSR Bond No. 490/CE/2024) 400 S/Eof11K.V.T.P.M.O.switchonpoleincludinghandlerodetc.completeinall respects as per direction of E/Ich.(PSR Bond No. 490/CE/2024) 401 S/E of 11 K.V. D.O. fuse set on pole complete in all respect as per direction of E/I.(PSR Bond No. 490/CE/2024) 402 Supply and laying of70 Sqmm 3 core 11 KV standered aluminium conductor XLPE(Cross linked polyethylene)insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade at a depth of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks on sides and on top put across. The armouring of cable shall be properly connectedwith earth conductor by clamps etc. PWD SOR No : 506 (d) (PSR Bond No. 490/CE/2024) 403 S/F of 70 Sq.mm size 3 core XLPE 11 KV outdoor type jointing kitproper completion of work as per direction of E/I A.R. Make: Raycheme, Mahindra. (PSR Bond No. 490/CE/2024) 404 S/F of level 2 following capacity 11/0.433 K.V. Al’ wound conventional 50Hz 3 phase oil immersed naturally cooled distribution T/F confirming and with amendments there of, havinglosses as per BEE standered with all standard fittings, including first filling of oil complete in all respects, of make UPPCL/KESCO Approved (PSR Bond No. 490/CE/2024)(a) 63 KVA (A.R.) 405 Supply and burring of Safe Earthing Electrode T-19 Zn-Zinc Coated, Length 3000mm, outer pipe 48.4mm x 3.2mm, inner pipe 26.9mm x 2.6, terminal Dia 12 mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 x 3 G.I. Strip will be extra)Make: As approved in U.P. P.W.D., & C.P.R.I. Certified.S.I.No-726 B/18. 406 S/Lof25mmx3mmGIstripfromearthelectrodedirectlyinthegroundasrequired complete in all respect Item No 716 SOR-2018 407 Supply and fixing of 2 metres high cage fabricated with 3mm thick expanded metal fixed on 50mm x 50mm x 6mm angle iron frame having vertical members spaced at 1 to 1.25 mts and horizontal members spaced at 1 mt. The vertical members shall be grouted in floor and horizontal members in the wall to a depth of 300mm with ends forked. The cage shall have 2000mm x 1000mm size one leaf door with locking device having door frame fabricated with 35mm x 35mm x 6mm angle iron and 3mm expanded metal duly fixed with the cage member with hinges etc. The cage shall be painted with red oxide primer and synthetic enamel paint. The job includes all materials, labour, T&P etc. for proper completion ofwork. PWD SI No : 1142 408 S/L of followingsize G.I.B classpipe ata depthof 750mmbelow groundlevel as cable carrier as direction of E/Inch. (PSR Bond - 490/CE/2024)(a) 80 mm dia

INR 4366 /-

INR 2742000.0 /-

INR 13.70 Crore /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB