Tender For Sinking 2 Nos Of Submersible With Over Head Tank (I) Near Ramnathpur Panchanan Mandir Gp-Hariharpur (Ii) Near Roichuddin Laskar House.Gp-Hariharpur Under Magrahat-I Ps - 1 SRINKING OF SUB-MARSHIBLE 2 Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.a) Depth of excavation not exceeding 1.50 m. 3 Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete 4 Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level, and filing joints with powdered earth or local sand 5 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. 6 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. 7 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(f) 25 mm to 30 mm shuttering without staging in foundation 8 (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction ofEngineer-In-Charge. 9 Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary),cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. 10 Brick work with 1st. Class bricks in cement sand morter 4:1a) In foundation & Plinth 11 125 mm thick Brick work with 1st class bricks in cement mortar (4:1) 12 Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(A) FloorWith Sand Cement Mortar (1:4)20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tileabove0.09 Sq.m (i) Coloured decorative 13 (B) WallWith Sand Cement Mortar (1:3)15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tileabove0.09 Sq.m (i) Coloured decorative 14 M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approvedmake and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the c 15 Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn)coating of 150 grams per sq. metre (followed by colourcoated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). 16 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of theEIC.a) Two Coat 17 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.b) Premium 100% Acrylic Emulsion 18 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](i) 1:4 cement morter; 15 mm thick plaster 19 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](i) 1:4 cement morter; 10 mm thick plaster 20 Labour for boring tube well of required dia. by water jet system throughany type of soil strata including hire and labour charges for boring pipes,scaffolding, tools and plants as necessary and taking out them andlowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the bore 21 d) For depth upto 150 metre for 50 mm dia. tube well with topenlargement of 100 mm dia. (ii) 100 mm dia 22 (i)40mm dia 23 (f) For depth more than 150 metre for 40 mm dia. tube well with top enlargement of 100 mm dia.(i)40mm dia 24 Supplying, fitting and fixing steel cutter piece upto 450 mm long with sockets.(i)40mm dia 25 Supplying high density polythene strainer of approved makewith adapter conforming to I.S. specifications.(i)50mm dia 26 Supply of PVC pipes & fittings Schedule 80 (medium duty) conformingto ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239a)40 mm dia 27 b) 100mm dia 28 Supply ,fitting & fixingPVCreducing socket with I.S.I. mark.( 100x 50) 29 Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with V notch including hire and labour charges for all tools and plants and scaffolding as required. 30 Supply fitting and fixing Submersible pumpset 1 HP capacityof approved make and brand(with complete set) 31 Supplying, fitting and fixing plug of approved make conforming to I.S. specifications. (ii) 40 mm 32 Collecting sample of water for bacteriological , chemical & arsenic test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction. 33 Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992(A) (i) Single Socketed 3 Meter Length (b) 110 mm 34 Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (b) 1000 litre capacity 35 Labour for hoisting plastic water storage tank. i) Upto 1500 litre capacity. (a) Upto 1st story from G.L. 36 Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work ( ii) 20 mm 37 (iii) 25 mm. 38 Supplying, fitting and fixing bib cock or stop cock.)(e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 mm 39 Supply, fitting & fixing of Name Plate and photograph 40 ADD 18% GST 41 Add 1.00% Labour welfare cess
