Tender For Road Signage Work On Khaliya Rawara Road Odr In District Bulandshahar From Ch. 0 000 To 9 750- Providing And Laying Of Hot Applied Thermoplastic Compound 2.5 Mm Thick Including Reflectorising Glass Beads @ 250 Gms Per Sqm Area, Thickness Of 2

Sharing tender

Tender For Road Signage Work On Khaliya Rawara Road Odr In District Bulandshahar From Ch. 0 000 To 9 750 - Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes..but Including cost of, all material,bitumen labour, T&P,royality , all taxes and labour cess complete. 22.2 MORTH-803(8.13) excluding GST 2 Reflective Raised Pavement Markers (Cat Eye/Road Stud) with shank Supply and fixing of raised pavement marker with Made of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High-Imoact Polystyrene) or Acryloniitrite Butadien Styrene (ABS) or Any other suitable material approved by the Engineer. The Marker shall support a load of 13,635 kg tested in accordance with ASTM D4280.The Reflective panels shall consist of number of lenses contatning single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face. Lenses shall be mouled of methyl methecrylate conforming to ASTM D788 of equivalent. The slop or retro-reflecting surface shall preferably be 35+/-5 degree to base and the area of each retro -reflecting surface shall not be less than 13.00 sq.cm. the marker height shall not be less than 10 mm and shall not exceed 20 mm &Width shall not exceed 130 mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marked with the name, trade or other means of identification of the manufacture. epoxy installations, excess adhesive around the edge of the marker, excess adhesive on the pavement and adhesive on the exposed surfaces of the markers shall be immediately removed. The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel , to the Engineer . In addition , a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. In case the markers are displaced , damaged , get worn out or lose their reflectivity compared to stipulated standards , the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer , at his own cost. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. excluding GST 3 Providing and fixing of 60 cm Circular Speed Limit/GO slow Board retro-reflectorised sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cement conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (as per IRC:67-2012 clause 14.60. excluding GST 4 Providing and fixing of 30 cm X90 cm Rectangular Hazard Marker retro-reflectorisedsign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cement conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing t of reinforcement & shuttering.The lateral vertical clearances and complete. Instalation work shall be as per relevant clause of MORT & H specification section 800 and IRC: 672010 compete in all respect.excluding GST 6 Retro Reflective Signboard made up to 2 mm thick alluminium sheet, face to be fully covered with 3 M high intensity prismetic reflective sheeting series 3930, letters/ symbols shall be made of sami retro reflective sheeting and computer cut as per colour required, boards are to be supplied along with back support frame of MS angle size 35x35x5mm , and back side of alluminium sheet shall be painted with stove enamel paint with seven years warranty . Rates include desin , fabrication , supply ,transportation and erection of the sign board . excluding GST