|
| 1 | Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : |
| 2 | 400 mm dia pile |
| 3 | Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :300 mm dia |
| 4 | 300 mm dia pile |
| 5 | Earthwork in foundation including digging and refilling the trenches with its proper disposal within 30 meters lead. |
| 6 | Earth work in filling with all lead & lift including cost of labour and T&P with proper completion of work as directed by Engineer-in-charge and as per I.D. specifications. |
| 7 | Providing and laying in position specified grade of plain cement concrete,excludingthecostofcentering,shuttering,finishing. 1:2:4(1 cement: 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Providing and laying in position specified grade of plain cement concrete,excludingthecostofcentering,shuttering,finishing. 1:4:8(1 cement: 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Centering and shuttering for C.C. work. |
| 10 | Centering and shuttering for R.C.C. work including all cost of materials,T&P and labours etc. finished. |
| 11 | Reinforced Cement Concrete 1:1.5:3 (Cement, coarse Sand and dalla grit) in column and plinth beam including all cost of materials,T&P and labours etc.finished including cost of steel complete. |
| 12 | Mild steel or iron in plain work such as reinforcement concrete or Reinforcement brick work (when not included in an over all rate) wrought to required shape as necessary including bending for proper completion of the work and including supply of all steel and wastage and over lapping & hooks. |
| 13 | First class brick work infoundation 1:6 cement mortar including all cost of materials,T&P and labours etc. |
| 14 | First class Brick work in 1:4 cement mortar |
| 15 | Plastering in 1:4 cement mortar including all cost of materials,T&P and labours etc. |
| 16 | Plastering in 1:3 cement mortar including all cost of materials,T&P and labours etc. |
| 17 | Extra for ceiling plaster |
| 18 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 19 | Extra for plastering on circular work not exceeding 6 m in radius: One Coat |
| 20 | Extra for plastering done on moulding, cornices or architraves including neat finish to lineand level:One Coat |
| 21 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption\"s less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1cement:4coarsesand) including grouting the joints with white cement and matching pigments etc. complete for size of Tile 60 X 60 Cm. |
| 22 | Laying of 25 mm thick KOTA STONE of size 45 x 45 cm and above flooring over previously prepared base with 2 cm thick 1:3 cement and sand mortar including filling of joints with cement mixed with pigment required for matching the shade of floor as per direction of E/I including cutting polishing with wax polish including supply of all materials T&P etc required for proper completion of the work. |
| 23 | Supply and fixing 6mm thick CHINA white glazed Tiles (ceramic tiles) in flooring/skirting or dado with 1:3 Cement mortar in kitchen and toilet including coarse sand working and the joints finishing with white cement slurry including all materials,labours tools etc. complete of work |
| 24 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepared the surface even and smooth complete |
| 25 | Distempering 1st coat with oil bound distemper of approved brand and manufacture and of required shade on undercoated wall surface to give an even shade over an including a priming coat cement primer of approved brand and manufacture such as Berger, J&N, Shalimar,Asian Paints after thoroughly brushing the surface free from mortar dropping and other foreign matters and also including preparing the surface even with plaster of paris or approved synthetic material andsand papered smooth including cost of all materials. |
| 26 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 27 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 28 | Providing and fixing T-iron frames for Doors, windows and ventilators of mild steel Tee-sections, joints mitred and lded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1Cement : 3 coarse sand : 6 graded tone aggregate 20 mm nominal size). |
| 29 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frameto be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. Thehinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1mm) wall thickness and 3 each. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction ofEngineer- in-chargeExtruded section profile size 48x40 mm |
| 30 | Providing and fixing to existing door frames :24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and railsmitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws.The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\"section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm)wallthickness, fixed to theshutter styles by means of plastic/galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mmgalvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter) |
| 31 | Providing and fixing stainless steel handles, ISI marked,with necessary screws etc. complete : 100 mm long |
| 32 | Providing and fixing stainless steel handles, ISI marked,with necessary screws etc. complete : 150 mm long |
| 33 | Providing and fixing stainless steel sliding door bolts, ISI markedwith nuts and screws etc.complete : 200x16 mm |
| 34 | Providing and fixing stainless steel sliding door bolts, ISI markedwith nuts and screws etc.complete : 300x16 mm |
| 35 | Providing and fixing stainless steel tower bolts, ISI marked,with necessary screws etc.complete : 100x10 mm |
| 36 | Providing and fixing stainless steel tower bolts, ISI marked,with necessary screws etc.complete : 200x10 mm |
| 37 | Providing and fixing Aluminium door stoper, ISI marked,with necessary screws etc.complete : 200x10 mm |
| 38 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete fixed to opening/wooden frames with rawl plugs screws etc. |
| 39 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm |
| 40 | Supply and fixing 5 MM thick Plain glass in window |
| 41 | Supply and fixing galvanized mosquito heavy quality iron wire gauge of expanded metal heavy quality our windows and including C.P. teak wood battens 3cmX10cm with servers and including supply of all in materials, labour and tools and plants etc. required for proper completion of work. (As per I.D. SOR page no. 39 S.No. 15) |
| 42 | With ordinary enamel paint or Varnish on ordinary building such as school, small office and type-I, II. IV residence. |
| 43 | Providing and laying \"Brick Coba\" 12mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15mm to each other , over 20mm thick base of cemet mortor 1:4 cemet and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortor mixed with water proofing compoud in 1:4 cement and coarse sand mortor finished smooth and top mashed false square 30cm x 30cm and side wall parapet shall be mono tythic plaster wall upto 30cm height and junction and corner shall be rounded by bbrick ballast cement and coarse sand masonary coba with top finished plaster mixed with acetic water proofing compound @ 2% by weight & includig S/o all material , labour T & P etc. copmlete for proper completion of work. |
| 44 | Providing and fixing panelled or panelled and glazed shutters for doors, windows andclerestory windows, fixing withbutt hinges of required size withnecessary screws,excludingpanellingwhichwillbepaid forseparately,allcompleteasperdirectionofEngineer-in-charge.Second class teak wood |
| 45 | 35 mm thick shutters |
| 46 | Providing wood work in frames of door,window,clerestory windows and other frames, wrought framed and fixed in position. |
| 47 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 48 | 50x50x5 angale |
| 49 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard ladder,railings,brackets,gates and similar works |
| 50 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 51 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting ofmain “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC(Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. |
| 52 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laidin required colour and pattern over and including 25 mm thick compacted bed of fine sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 53 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concretework to be paid for separately). Payment to be made per metre cost of total lengthof barbed wire used.With (G.I. barbed wire) |
| 54 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts andwashers as required complete as per the direction of Engineer-in-charge. |
| 55 | Supplying and fixing 10 Gauge weld mesh of size 100 mm x100 mm for floor/roof slab concrete screed over the micro beams as reinforcement. The weld mesh shall be fixed as per drawing. |
| 56 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 57 | 40 mm dia (External work) |
| 58 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm dia (External work) |
| 59 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.15 mm dia (Internal work) |
| 60 | Fixing gun metal check for non return valve of all nominal base.25 mm dia |
| 61 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: (15mm dia) |
| 62 | P/F C.P. brass angle valve for cistern , wash basin,Gyeser etc 15mm nominal hole size including cost of all materials, labour T&P etc. |
| 63 | P/F 15mm nominal hole size C.P. stop cocks |
| 64 | Fixing 15mm PVC connection, heavyquality with brass Union including supply of all materials, labour T&P etc. required for proper completion of the work. |
| 65 | P/F in position C.P. brass towel rail complete with brackets including gchases in wall and repairing the same in 1:3 CM complete.750X20 cm |
| 66 | Fixing C.P. Brass soap dish with C.P. brass brackets fixed to wooden plugs, plastic sleeves with C.P. Brassscrews. |
| 67 | P/F C.P. Brass toilet paper holders including cost of all materials, labours T&P etc. |
| 68 | P/F C.P. Jali for Nahani Trap 100mm dia including cost of all materials |
| 69 | P/F C.P. Brass waste pipe for sink and washbasin in 32mm dia complete, cost of all materials, labour T&P etc. |
| 70 | P/F wash basin with single hole/number of holes for CP brass pillar tap with C.I. or M.S. brackets painted white including cutting hole & making good the same but excluding fittings ( 630 X 450cm.) |
| 71 | P/F pedestal for wash basin complete recessed at the back for the reption of the pipes and fittings. |
| 72 | P/F stainless steel kitchen sink with C.I.bracket excluding cost of other fitting. (Kitchen sink without drain borad size (610 X 510 X 200mm) |
| 73 | P/F 15mm nominal hole size C.P. brass pillar cocks. |
| 74 | P/F chromium plated shower rose with 15mm as 20mm inlet complete and 100mm dia |
| 75 | Providing and fixing 600x400 mm beveled edge mirror of superior glass (ofapprovedquality) complete with 6 mm thick hard board ground fixed to wooden cleats withC.P. brass screws and washers complete |
| 76 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 77 | Providing & Fixing water closet Squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 ltr low level white PVC flusing cistern with manually contrilled device (handle lever) confermng to IS : 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. White vetreous china orrisa pattern W.C. pan of size 580 x 440 mm with integral type foot rests. |
| 78 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern& C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, over flow arrangement with specials of standard make and mosquito proof coupling ofapproved municipaldesign complete, including painting of fittings andbrackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 79 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (110 mm diameter) and T&P |
| 80 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110 mm bend |
| 81 | Single tee with door (110x110x110 mm) |
| 82 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 83 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete withC.I. grating brick masonry chamber with water tight C.I. cover with frame of300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg andframe to be not less than 2.72 kg as per standarddesign:100x100 mm size P type With common burnt clayF.P.S.(nonmodular) bricks of class designation 7.5 including excavation. |
| 84 | Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729 for bathroom and kitchen upto gully trap and up |
| 85 | Providing lead chaulked jointes to cast iron soil waste & ventilation pipes and fitting of the following nominal size/diameters including testing of joints. 100 mm dia |
| 86 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm dia Sand cast iron S&S as per IS - 1729 |
| 87 | Providing, Laying and fixing inj position salt glazes S.W. full round pipe , IS:651 (grade-A) with 1:2 cm with spun yarn or gasket laid under ground over 15cm C.C. 1:4:8 and in cased in proper gradient including excavation of trenches up to 2m depth (150mm dia) |
| 88 | Proving and Fixing of 15 mm dia ball valve (Brass) of approved quality,high or low pressure with plastic floats. |
| 89 | P/F cost iron floor trap self cleaning design with sand cost iron screwed down as hinged grating with or without vent arm complete including cost of cutting and making good the walls & floors. |
| 90 | P/F white vitreous china flat back urinal size 580X380X350mm with 5 lit, P.V.C. flushing cistern, flush pipe, C.I. trap and grating complete in all respect. |
| 91 | Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :550 mm dia piles |
| 92 | Wiring point for light with 1.0sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable earth continuity wire, piano type switch & celing rose/angle/batten holder on 3 mm thickphenolic paminated backelite sheet etc complete in all respects as per direction of Engineer in Charge. , including matching color wash. |
| 93 | Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.0 sqmm FRLSH PVC insulated multistrand single core copperconductor cable in PVC conduit pipe partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq. mm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitcontinuity wire, piano type switch & celing rose on 3 mm thickphenolic paminated backelite sheet etc complete in all respects as per direction of Engineer in Charge. , including matching color wash. |
| 94 | Wiring point for plug with 1.0 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq. mm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitcontinuity wire, piano type switch & socket etc complete in all respects as per direction of Engineer in Charge.including matching color wash. |
| 95 | Wiring Point for call bell with 1.0 sq. mm. FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 1.5 sq. mm FR PVC insulated multistrand copper earth contunity wire andpiano type bell push or 2 pin socket etc complete in all respects as per direction of Engineer in Charge.including matching color wash. |
| 96 | Add for light / fan points with modular type switch in place of piano type switch as per direction of Engineer in Charge. . |
| 97 | Add for plug point with modular switch & socket in place of piano type switch & socket as per direction of Engineer in Charge. . |
| 98 | Add for HPMV/Exhaust fan point with modular type switch in place of piano type switch as per direction of Engineer in Charge. . |
| 99 | Add for Call bell point with modular type bell push in place of piano type bell switch as per direction of Engineer in Charge. . |
| 100 | Supply and wiring of submain with two number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm diaheavy duty (2mm thick) PVC conduit with 1 nos. 1.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect as per direction of Engineer in Charge. . |
| 101 | Supply and wiring of submain with two number 1.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2mm thick) PVC conduit with 1 nos. 2.5 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect as per direction of Engineer in Charge. . |
| 102 | Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavyduty (2 mm thick) PVC conduit with one no. 2.5 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit as per direction of Engineer in Charge. . |
| 103 | Supply and wiring of 4 number 10 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 32 mm dia heavyduty (2 mm thick) PVC conduit with 2 nos 6 sq.mm. FRLSH PVC insulated copper conductor cable as earth continuity wire drawn in conduit as per direction of Engineer in Charge. . |
| 104 | Supply and wiring of 4 number 16 sq. mm. PVC insulated 1100 V grade single core Copper conductor cable in 40 mm dia PVC conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with two number 10 sq mm single core Copper conductor cable as earth continuity wiredrawn in coudit including matching colour wash etc, complete in all respect as per direction of Engineer in Charge. |
| 105 | Supply and fixing of call bell of approved make on polished MDFEG/ Teak ply board including making connections etc. complete in all respect as per direction of Engineer in Charge. . |
| 106 | Supply and fixing of recess/ Surface/ Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect as per direction of Engineer in Charge. . CAT-AAA |
| 107 | Supply and fixing of 12 Watt to 15 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing with extended heat sink, diffuser of Polycarbonate meterial and driver set complete in all respect as per direction of Engineer in Charge. .CAT-AAA |
| 108 | Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect as per direction of Engineer in Charge. CAT AAA |
| 109 | Supply and fixing of Single LED light wall bracket 3 to 6 Watt on matching M.D.F.E.G Board base etc. complete in all respect as per direction of Engineer in Charge. CAT-AAA |
| 110 | Supply and fixing of switch box 150 x 150 x 65 mm size size of approved make made up of 1.0 mm thick ISI Marked G.P.sheet All 4 corners folded & spot welded for screw and holes plugged with PVC Nylon Caps . Two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. Holes shuld be semi-shuttered type and fitted with heavy brass Earth Piller duly screwed & brand name should be embossed. Box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the Engineer in charge. |
| 111 | Supply and fixing of switch box 250 x 300 x 65 mm size size of approved make made up of 1.0 mm thick ISI Marked G.P.sheet All 4 corners folded & spot welded for screw and holes plugged with PVC Nylon Caps . Two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. Holes shuld be semi-shuttered type and fitted with heavy brass Earth Piller duly screwed & brand name should be embossed. Box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the Engineer in charge. |
| 112 | Same as in item No 159 but of but size 250 x 300 x 65 mm size |
| 113 | S&F of 6 Amp to 32 Amp. MCB (10 KA) C Curve as per direction of Engineer in Charge. |
| 114 | CAT A |
| 115 | S&F of 63 Amp. 4 pole MCB(10 KA) C Curve as per direction of Engineer in Charge. |
| 116 | CAT A |
| 117 | S&F of single pole MCB blanking plate as per direction of Engineer in Charge. |
| 118 | CAT A |
| 119 | Supply and fixing of power plug with 20 Amp./250 volt flush type modular switch and 5 pin 20 A/250 volt flush type universal modular socket switch on concealed M.S box including supply of all material, labour T&P etc. required for proper completion of work as per direction of Engineer in Charge. |
| 120 | Supply and fixing of 16 gauge M.S. drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respect as per direction of Engineer in Charge. |
| 121 | Supply and fixing hexagonal/Round G.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work as per direction of Engineer in Charge. |
| 122 | Supply and fixing of electronic fan regulator( Modular) 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work. |
| 123 | EARTHING |
| 124 | Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mm x 3mm G.I. strip, upto switch board (from apron to switch board, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing. Make: As approved in U.P. P.W.D., & C.P.R.I. Certified as per direction of Engineer in Charge. |
| 125 | Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect as per direction of Engineer in Charge. |
| 126 | Supply and fixing of one number 8 SWG G.I. wire in 15mm dia. G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site by Engineer in Charge. |
| 127 | Supply & fixing of wall roof type service bracket of 50 mm dia 4 Meter long fabricated from class \"B\" G.I. pipe complete with two bends, sockets, wall clamps. 7/3.15 mm G.I. stay wire, stay insulators etc. complete in all respect as per direction of Engineer in Charge. . |
| 128 | Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 110 to 130 Watt. Confirming to IP 66 Protection complete in all respect as per direction of Engineer in Charge. |
| 129 | CAT- AAA |
