Tender For Addn/Altn To Mes Complaint Cell At Af Stn Chimney Hills; 1 Taking down cement plaster on brick work or stone walls etc incl raking out joints hacking for key scrubbng down with water complete all as directed. 2 Demolition of PCC block walling/brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 3 Demolition of unreinforced cement concrete in ground floor and paving n.exc 15cm thick (below or above ground level) etc complete all as specified and directed. 4 Taking down chowkats or frames with shutters ( without taking of shutter from the frame) n.exc 1.5 sqm each complete all as directed. 5 Taking down chowkats or frames with shutters ( without taking of shutter from the frame) exc 1.5 sqm but n.exc 4.00 sqm each complete all as directed. 6 M&L for pre cast cement concrete solid block masonry 1:3:6 type C-1(using 20mm aggregate)with solid block exc 10cm in width setting in CM 1:4 etc complete all as specified and directed. 7 M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth without using extra cement in internal surfaces complete all as specified and directed. 8 M&L for rendering 10 mm thick on ceiling as in chajja in CM 1:3 even and smooth without using extra cement complete all as specified and directed. 9 M&L for preparing new plaster surface apply two coat of oil bound distemper over a coat of wall care putty to obtained smoothness of wall surfaces over one coat of primer complete all as specified and directed. 10 M&L for complete remocal of plastered surface and apply two coat of oil bound distemper over a coat of wall care putty to obtained smoothness of wall surfaces over one coat of primer complete all as specified and directed. 11 M&L for preparing new plaster surface apply three coats of white wash ceiling surfaces complete all as specified and directed. 12 M&L preparation and washing, rubbing down and stopping of distempered and painted surfacesof wall including cornices and applying one coat ofacrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturers specification complete allas directed. 13 M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) of 25mm thick as in correction/levelling course, finished surfces even and rough to receive floor finishcomplete all as directed. 14 M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl over screed bed or bedding layer of mortar 15mm thick for laying tiles in cement mortar 1:6 complete all as directed. 15 -ditto- but as in skirting over 10mm thick rendering as in backing coat of CM 1:4. 16 M&L for Glazed ceramic coloured tiles of size 300x450x7mm/350x450x7mm thick over and incl 10mm thick rendering in cement mortar 1:4 as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed. 17 M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed in CM 1:4, 15mm thick base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing complete all as directed. 18 -ditto- but as in skirting incl 15mm thick backing coatin CM 1:4 complete all as directed. 19 M&L for Marble Makrana white 18-20mm thick machine cut as in border laid over & including 15mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match and incl polishing complete all as directed. 20 M&L for PCC 1:4:8 type D-2 using 40mm stone aggregate as in sub base of flooring and mass concrete complete all as specified and directed. 21 M&L for provinding 75mm thick cement concrete in 1:3:6 type C1, (using 20mm graded stone aggregate) finishing cement concrete surface even and fair without using extra cement as in plinth protection complete all as directed. 22 M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete 23 M&L 35mm thick flush shutters, solid core construction, withpartical board core and plywood face panels, both face is covered with decorative face veneer with glipping/frames complete (Design and pattern approved by AGE(I)) all as specified and directed by Engineer-in-Charge. 24 S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay,complete with glazing bars, dovetailed or welded complete 25 S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay,complete without glazing bars, dovetailed or welded complete 26 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm long complete. 27 S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 28 S&F 100mm MS butt hinges cold rolled mild steel, and fixedcompleteall as specified and directed. 29 S&F Aluminium anodised, barrel tower bolts 150mm of extruded section and fixed 30 S&F Aluminium anodised, handles 150mm of extruded section and fixed 31 S&F in repair for 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washer complete all as specified and directed. 32 S&F for Powder coated aluminium frames and shutters/grills for door and window, ventilator or framing with one or more rebates joining cleat for fixing etc of any thpe, side hung shutter, sliding shutters etc complete all as specified and directed by Engr-in-Charge. 33 M&L for Rubber gasket EPDM/Neoprene for fixing glass pane in aluminium frame work/door/window complete all as specified and directed by Engr-in-Charge. 34 S&F Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square of any size in each pane all as directed by Engr-in-Charge 35 S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples 36 S&F in repair for Drapary rod 20mm dia, mild steel, chromium plated with fixing brackets, stops etc all as specified and directed by Engr-in-Charge. 37 S&F in repair Brackets suitable for drapary rod, mild steel, chromium plated etc all as specified and directed by Engr-in-Charge. 38 M&L preparation steel surfaces with two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. 39 S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work conforming to Fe.290.Gde-E-165 40 M&L RCC Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likeall as directed by Engineer-in-Charge. 41 M&L form work for rough finished surfacesto soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping) all as specified and as directed 42 M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars. 43 M&L preparation wood surfaces with two coats of Synthetic enamel paint over one coat of pink primer complete all as specified and directed. 44 M&L Veneered decorative plywood 12mm thick, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and directed. 45 M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) of 25mm thick as in padding course, finished surfces even and rough for roof treatment complete all as directed. 46 M&L for 10mm thick plastering in CM 1:3 on concrete surfaces finished even and smooth complete all as specified and as directed. 47 Supply only Integral waterproofing compound. 48 Applying Oil bound Bitumen primer @ 0.20 Kg/Sqm all as specified and directed by Engineer-in-Charge. 49 M&L APP minimum 4mm thick polymeric membrane minimumweighing not less than 4kg/sqm and reinforced with polyster nonwoven fabric matt(wt. notless than 150 gms/sqm) & applying a coat of blown hot Bitumen over the membrane @ 12.0 kg/sqm complete all as specified and directed by Engineer-in-Charge. 50 Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. 51 Material and labour for cleaningthe surfaces and removing stains using sand paper, filling cavities, cracks with approved filler material like bees wax, raw-zina, chalk powder etc., mixed with polish, applying high gloss french polish, till the final glossy finish and uniform texture is achieved (undersides/hidden portion directly not visible shall be excluded) for the following items of furniture complete all as specified and as directed. 52 (a)One light pointcontrolled by one, one way switch 53 (b) One Fanpointcontrolled by one, one way switch 54 (c ) One Exhaust fanpointcontrolled by one, one way switch 55 (d)One wall fanpointcontrolled by one, one way switch 56 All as per item No 2 herein before but One three pin socket outlet 5 Amp controlled by one, one way switch on independent board 57 All as per item No 2 herein before but One three pin socket outlet 5 Amp controlled by one, one way switch on sameboard 58 All as per item No.2 above but with 2.5 sqmm cable for socket outlet 3 pin 15 Amps on independent board incl 2.5 sqmm PVC standard copper conductor cable as earth continuity conductor . 59 S & F in repair switch piano 6 Amps one way flush type 60 S & F in repair switch piano 16 Amps one way flush type 61 S&F in repair socket, 2 in 1, 3 pin 5 Amps flush type 62 S&F in repair socket 2 in l, 3 pin 6 Amps and 3 pin 16 Amps flush type. 63 S&F Lamp holder,Angle and battentype, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings all as specified and directed . 64 Supply and fix in repair fan regulator AC230 V electronic socket type 65 S&Fin repair ceiling rose 3 terminals ,ISI Marked all as specified and directed . 66 S&F LED lights fitting 1x 20 W of lumens 110 /Watt ,4 feet,220V, 6500 K,AC decorative box type with driver, holder including Retrofit LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete 67 S&F LED light fitting integratedtype with high out put diffuser 2 feet, 10 watt of lumens 100 /Watts,220 V AC decorative type with driver holder and LED lamp including connecting up with two core flexible copper conductor cable of suitable size complete. 68 S&FLED Bulb ,B22 Type ,10 W of Minimum lumens 105 /watt,6500 K Temperature ,3 star rated all as specified and directed . 69 S & F MCB SP 6 to 32 Amps10 KA 240V 50HZ, ISI Marked . 70 All as per item No. 16 above but MCB SPN 6 to 32 Amps 71 S&FRCCB, DP, 40 Amps AC type in accordance with IS:12640-1 and IEC-6100-1, suitable for 240 Volts, 50 Hz with 10 KA short circuit withstand capacity. 72 M& L for Taking down existing Ceiling fan 1200/1400 mm sweepfrom its location Serviceing and Rewinding of ceiling fan/motor with super enameled copper winding wire of similar gauge and weight of the original winding insulating with class B, varnishing, drying,and relacing of capacitor,GM bushes,ball bearing,shakleetc complete, including refixing the same after carrying out the repair all as specified and directed . 73 All as per item No.19 above but for Wall fan any sweep . 74 Supply and fix Exhaust fan,metal body ,AC single Phase. 230V of size 250mm sweep with 810CMH Air delivery ,37 W Consumption,frame and louvers all as specified and directed by engineer in charge. 75 M&L for Making Hole in Stone wall for fixing of Exhaust Fanof 250 mm and Making Good disturbed surface by plasteringand painting completeall as per directed by engr in charge. 76 S & F in repair MCB distribution board SPN 8 way single door 240V powder coated with 200 Amps rated bus bar neutral link etc. 77 M&L in replacement submain wiring /Circuit wiring with PVC insulated, single core, multi stranded, 1100 volts grade unsheathed copper conductor cable in and including PVC Conduit/Casing capping with accessories fixed on wall /ceiling with GI screws complete with 2x4 Sqmm +1x 4 Sqmm for earth continuity conductor all as directed. 78 All aser item No 24 here in before but 4x4 Sqmm +1x 4 Sqmm for earth continuity conductor all as directed. 79 S&F sheet metal enclosures with socket, plug top including MCB SPcapacity 20 Amps all as specified and directed by engineer in charge . 80 S&F of 35/36 watts LED Security light fitting with pressure die cast IP 65 protection, luminous efficiency of 100 lm/watt, PF > 0.95, CRI > 80, colour temprature 5700 K suitable for primary roads with all connected accessories including bracket made out of GI tubing of 40 mm light grade outer dia, 1.2m length,with GI clamps, nuts and bolts etc for fixing of fitting complete all as specified. 81 S&F sheet metal enclosures with socket, plug top including MCB SPcapacity 20 Amps all as specified and directed by engineer in charge .
