|
| 1 | Earthwork excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Soft disintegrated rock, laterite, soft rock or kankar,not requiring blasting. etc. complete complying with standard specification |
| 2 | Refilling with excavated soil (other than sand) complying with Standard Specifications for filling in the foundation and basement. etc. complete complying with standard specification |
| 3 | Supplying and filling basement with conveyed earth like Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders SS.20Betc. complete complying with standard specification |
| 4 | Providing and laying in position, for Plain Cement Concrete 1:5:10 (One Cement, Five Manufactured sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification |
| 5 | Removal of existing Heavy jungle and clearing site for construction workand clearing area as directed by officers |
| 6 | Filling with river sand to the foundation and basement including watering and consolidating as per standard specification. |
| 7 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. |
| 8 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. |
| 9 | For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. |
| 10 | For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. |
| 11 | For plane surfaces such asrectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc. |
| 12 | Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers. |
| 13 | Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS:456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 325 kg/ms and maximum water cement ratio of 0.55, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, reta?d setting of concrete, improveworkability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushedstone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79cu\"m\") 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering andshuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providingfixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., completecomplying with standard specification and as directed by the departmental officers. The coarse and fineaggregates to be used should comply with the requirements of IS standards. |
| 14 | Foundation and Basement |
| 15 | Super Structure Ground Floor up to 4.50m |
| 16 | Supplying, fabricating and placing in position TMT Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. |
| 17 | Providing and laying in position, Random Rubble Masonry Work using 1:5 Cement Mortar using best quality of Hard Random Rubble masonry stones for foundation and basement including curing, etc.,including and material in all respect, complete complying with standard specification |
| 18 | a)Foundation and Basement |
| 19 | b)Ground Floor up to 4.50m |
| 20 | c) First Floor |
| 21 | Providing and laying in position, Brick Work in Cement Mortar 1:5 Mix (one cement, Five sand) using new best Wire Cut Bricks for Heritage Works of size 9\" x 4 1/2 \"x 3\" from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications. |
| 22 | a) Upto Basement |
| 23 | b)Super Structure Ground Floor up to 4.50m |
| 24 | Brick partition walls of 11.50cm thickness using best quality II class ground moulded chamber burnt bricks of size9”X 4-1/2”X3” in cement mortar 1:3 (one cement and three sand) using hoop iron reinforcement if found necessary including curing etc., complete complying with standard specification |
| 25 | Plastering with cement mortar 1:5 (One cement, and five sand) 12mm thick including curing, cost and conveyance of all materialscomplete complying with standard specification |
| 26 | Special ceiling plastering for RCC works with Cement Mortar 1:3 (One cement, and three sand) 10mm thick including curing, cost and conveyance of all materialscomplete complying with standard specification |
| 27 | Painting two coats of newly plastered wall surface with ready mixed interior plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 28 | Painting two coats of newly plasteredwall surface with ready mixed exterior emulsion paint first quality and approved colour over a priming coat including through scrapping, clean removed of dirt, and including necessary plaster of paris putty, wherever required etc. complete complying with standard specification. |
| 29 | Painting new iron works with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. |
| 30 | Water repellent paint 3 coats over the Exposed brick work and exposed brick tile area Including cost of all materials to site and all labour charges for mixing applying etc., Complete as per Standard Specifications. |
| 31 | Dadooing walls with following best approved quality, Porcelain tiles set in Cement Mortar 1:3 (One Cement and Three plastering sand) 600mmx600mm x8 mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / m² neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. |
| 32 | Providing and laying in position, Floor Tile antiskid following best approved quality, Porcelain tiles set in Cement Mortar 1:3 (One Cement and Three plastering sand) 10mm 600mm x600mm x8 mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / m² neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. |
| 33 | Providing and laying in position, Finishing the floor with one course of Terracotta machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stoneSand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers |
| 34 | Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections.Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.Hardware: All the hardware like friction stays, handlesshould be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designedsuch that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wallusing self expanding nylon plug and driving ms electroplated screws into plug.complete complying with standard specification |
| 35 | Supplying and fixing UPVC (Un-Plasticized PolyvinylChloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided withEspag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockableaction, security protective hinges, strong lockingsystems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packingwith screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work., complete complying with standard specification |
| 36 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mmboth profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.,complete complying with standard specification |
| 37 | Supplying and fixing Iron grills to the windows made out of square rods including cost fabrication, conveyance and fixing in position etc.,complete complying with standard specification |
| 38 | Supplying and fixing Teak Wood Frames for Doors, Windows, Ventilators and other similarjoinery works with the following sizes and sectionsincluding labour charges for wrought and put up in position and also for fixing hold fast in frames andmasonry etc complete in all floors.Teak Wood Scantling upto 2m length |
| 39 | Providing and Fixing In Position for Urinals Stone Partition Walls 600x1200x20 mmSinthetic Grey, Paradise and similar varieties grinding for the edges etc complete as directed. |
| 40 | Labour charges for grinding the urinals partition granite slab edges into half round shape including cost of cutting blade and labour charges for grinding etc as per standard specification. |
| 41 | Providing and laying in positionNatural Stone with Flamed Finishof size 1000mmx300mmx17 mm thick antiskid tile (for Ramp) following best approved quality, set in Cement Mortar 1:3 (One Cement and Three plastering sand) and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / m² neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. . |
| 42 | Manufacturing, Supplying and Fixing of Mild Steel Railing using Circular TubeSection40mm & 4mm thick and Ø50mm & 4mm with Dark Grey Enamel Paint Finish in Pathways, andother areas as per drawing. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, Painting, conveyance, electrical charges, etc. complete as directed. |
| 43 | Manufacturing, Supplying and Fixing of Side Horizontal Pipe Members Using Mild Steel (MS) RHS 100X200X6 mm Rectangular Hollow Steel Pipe Sections with Two Coat Primer and Dark Gray Enamel Paint Finish. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, Painting, conveyance, electrical charges, etc. complete complying with standard specification |
| 44 | Manufacturing, Supplying and Fixing of Mid Horizontal Pipe Members Using Mild Steel (MS) SHS 100X100X4mm Square Hollow Steel Pipe Sections with Two Coat Primer and Dark Gray Enamel Paint Finish. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, Painting, conveyance, electrical charges, etc. complete complying with standard specification |
| 45 | Supplying and Fixing of Chequered Plywood of 25mm thick of approved make (kitpy /Sheron or equivalent ) over the existing M.S sections with 3mm thick alumimium strip, self tapping screws complete as per directed |
| 46 | Supply and installation of FRP/PVC storage water tank with double flab cover of approved quality and make including conveyance and lifting to top of terrace and fixing in position etc., complete. In the tank,necessary holes to be made for inlet,outlet and over flow connections. The rate is including cost and conveyance of all materials and labour for erection etc.,complete as per directed |
| 47 | Manufacturing, Installation of Bio Treatment Tank for Commercial / Residential use. (Made up of FRP)Including - ennZyme (Culture with Aerobic & Anaerobic form) (Output treated water suitable for surface disposal and COD, BOD and PH value confirming to as per TNPCB norms) complete as per directed |
| 48 | a)Flexi Bio Digester Tank 5000 Liters Capacity Including ennZyme |
| 49 | b)Digging & Leach Tank and Installation Charges |
| 50 | SupplyingBoats |
| 51 | Supplying GRP Four Seater Pedal Boat (Twin Hull Type) ofsize 3.0 m length ,Beam -1.50m, Depth -0.45m,Draft - 0.25m, Non skid walking area ,all round fender with adequate buoyancy tanks,3 nos of Brass/Gun metal cleats,foldable canopy with Al.Tubalar frame and PVC coated nylon, 2 person pedaling system with SS shaft.Propelling system with SS shaft and fiber glass blades as percomplete as per directed |
| 52 | Supplying GRP 2 Seater Pedal Boat(Twin Hull Type) Model No. MM-10-PT2ofsize 2.40 m length ,Beam -1.50m, Depth -0.60m,Draft - 0.25m, Non skid walking area ,all round fender with adequate buoyancy tanks,1 no of Brass/Gun metal cleats,foldable canopy with Al.Tubalar frame and PVC coated nylon, 2 person pedaling system with SS shaft.Propelling system with SS shaft and fiber glass blades as percomplete as per directed |
| 53 | Supplying Aqua cycle Supplying Aqua cycle (Tri wheeled pedal boat hull ) ofsize 3.0 m length ,Beam -1.80m, Depth -1.20.m,Draft - 0.30m,2 persons capacity ,fiber glass seat , Non skid walking area ,all round fender with adequate buoyancy tanks, 2 person pedaling system with SS shaft.steeringsystem with handle and forepeak wheelcomplete as per directed |
| 54 | Life Buoyfor Adult &Kids |
| 55 | Life Jacket for Adult &Kids |
| 56 | conveyance Charges for All Baots and Life Buoy,Life Jackets |
| 57 | Supplying and Fixing of Sign Board at Main Entrance Back side of Ticket Counter Wall2 nos Design, Fabrication, Supply and Installation of Tourist Destination Map Boards (1800 x 1200 mm laminated with site map and MS frame)1. Digital Map Design & Content Creation2. High-resolution Printing & Lamination3. Aluminium Composite Panel (ACP) Sheet4. MS Frame Fabrication (Powder Coated5. Steel Posts (Galvanized, with base plates)6. Cement Concrete Foundation (1:2:4 mix)7. Transportation and Handling8. Installation & Labour Chargescomplete as per directed |
| 58 | Other Sign Boards |
| 59 | Frame:A. Frame made of 1\" x 1.5” Hallow Mild Steel (MS) Square Bars of 14gauge primer coated with red oxide.B. Frame is covered with 4 mm ACPC. Back panel made of GI sheet primer coated and painted.D. Complete Fabrication, Mounting and Installation of the ACP signageE. 4 MM EXTERIOR GRADE ACP SHEET of bright silver colour, ACP sheetsto be joined from back with minimum gap visible from the front andsilicone for joining gap. ACP to be mounted from 5 Sides ,pasted withlaser cut 1inch raised imported acrylic covering letters as per logocolors as shown in the attached artwork.F. Artwork as per Architectural Design |
| 60 | Fascia:Exterior Grade Silver color ACPACP PVDF: Aluminum composite panels, composed of laminate 2 color paintedaluminum sheets with plastic cores, in the plate form and with the thickness of4mm. Reputed suppliers like Aludecor/Timex/Alubond/ Alstrong ACP.ACP should have attributes such as superior flatness, rigid, light weight, durable,vibration dampening, ease of maintenance Weathering, Corrosion and ChemicalResistant and environmentally Friendly.Acrylic: Clear Cast Grade imported Acrylic sheetA. 3 mm thick external grade Imported acrylic, Male & female lettering (Back Lit).B. color - as per our Brand colorC. CMYK value of Balmerol logoRed : - 0 C, 100 M, 100 Y, 0 K ( 0.100.100.0)Green : 100 C, 0 M, 111 Y, 30 K ( 100.0.100.30)Vinyl: Vinyl should be of reputed brands with warranty offers like Vinyl LG Hausysgrade / Avery HIGH PERFORMANCE FILMS/ 3M Long-Term Vinyl series/Arlon2100/Series |
| 61 | Support:Supply and Installation of 100mm Diameter MS Hallow Circular Pipe fixing inRCC Readymade Pedestal with 200mmx200mm MS Base Plate fixing with Bolts |
| 62 | Supplying, laying and jointing CPVC pipes of 25mm dia meter and best variety conforming to ISS including fixing CPVC specials and fixing to wall/ floor with necessary clampsmaking holes on the wallcomplete as directed by the corporation officers complying with standard specification. |
| 63 | Supplying, laying and jointing CPVC pipes of 20mm dia meter and best variety conforming to ISS including fixing CPVC specials but excluding cost of such specials and fixing to wall in a concealed manner, making holes on the wall or drilling holes in roof etc and making good of the dismantled portions etc complete under concealed internal water supply arrangements.complete as directed by the corporation officers complying with standard specification. |
| 64 | Supply of the following sizes of CPVC specials of approved quality conforming to ISS complying with standard specification. complete as directed by the corporation officers complying with standard specification.. |
| 65 | 25mm CPVC Plain Elbow |
| 66 | 25mm CPVC Union |
| 67 | 25mm CPVC Valve |
| 68 | 25mm x 20mm Plain Elbow |
| 69 | 20mm CPVC Plain Elbow |
| 70 | 20mm CPVC Plain Tee |
| 71 | 20mm x 15mm Brass Tee |
| 72 | 20mm x 15mm Brass Elbow |
| 73 | Supply, laying and jointing UPVC pipes of the following dia meter and best variety conforming to ISS including fixing UPVC specials but excluding cost of such specials and fixing to wall / floor with UPVC clamp set,making holes on the wall or drilling holes in roof etc., and making good of the dismantled portions etc complete under external water supply arrangements as directed by the corporation officers complying with standard specification. |
| 74 | 40mm dia UPVC Pipe |
| 75 | 25mm dia UPVC Pipe |
| 76 | Supply of the following sizes ofUPVC specials of approved quality conforming to ISS complying with standard specification. |
| 77 | 40mm UPVC Union |
| 78 | 40mm UPVC coupler |
| 79 | 40mm UPVC Elbow |
| 80 | 40mm UPVC Tee |
| 81 | 40mm x 25mm UPVC Push |
| 82 | 25mm UPVC Plain Elbow |
| 83 | 25mm x 20mm Plain Elbow |
| 84 | Supplying and fixing in position of best quality PVC waste pipe of the followingdiameter and 6kg/cm2 class having ISI mark and providing leak proof joints including fixing to the wall with PVC clamps etc and making connection to all sanitary fittings, dismantling masonry / RCC wherever necessary & making good the dismantled portion to the original condition complying with standard specification. |
| 85 | 75mm dia PVC waste Pipe |
| 86 | 110mm dia PVC waste Pipe |
| 87 | Supply and fixing in position of best quality PVC specials of the following dia such as plain elbow, door elbow, plain tee, door tee, off sets, Y junction etc, conforming to ISI mark and providing leak proof joints including fixing to the wall with PVC clamps etc and making connection to the PVC soil stacks, dismantling the brick masonry/RCC floor (or) roof slab and redoing the same etc complete complying with standard specification. |
| 88 | 75mm door Elbow |
| 89 | 75mm Plain Elbow |
| 90 | 110mm Plain Elbow |
| 91 | 110mm Door Elbow |
| 92 | 110mm Door TEE |
| 93 | In the Vent pipe |
| 94 | Supply and fixing 4” dia PVC Nahini trap with S.S grating using size 100mm x 75mm PVC trap and 125mm dia S.S grating of approved quality etc. as directed by the corporation officers complying with standard specification |
| 95 | Supply and fixing Jaquar or equivalent white European closet water closet 345mm x 490mm x 360mm with accessories such as seat cover, 12 litre capacity open PVC cistern, Single piece.The rate is including cost of all other fittings such as 15mm C.P angle cock - 1No (Jaquar or equivalent), 15mm x 450mm nylon connection - 1No (Jaquar or equivalent) etc, complete complying with standard specification. |
| 96 | Supply and fixing Jaquar or equivalent white indianwater closet 550mm x 450mmwith accessories such as12 litre capacity open PVC cistern,.The rate is including cost of all other fittings such as 15mm C.P angle cock - 1No (Jaquar or equivalent), 15mm x 450mm nylon connection - 1No (Jaquar or equivalent) etc, complete complying with standard specification. |
| 97 | Supplying and fixing Jaquar or equivalent make White table top wash basin (JDS WHT - 25937 model)of size 500mm x 380mm x 120mm with all other accessories such as 15mm c.p pillar cock-1No, (jaguar FLR 5011N) -1No,15mm C.P angle cock - 1No (Jaquarcon - 053KN model),-1No, 15mm heavy duty PVC connection, 32mm CP waste coupling and 32mm waste hose etc, as directed complying with standard specifications. |
| 98 | Supply and fixing 15mm FLR-CHR-5041N C.P two way bib cock (39191000) (Jaguar flourantine or equivalent) with 1200mm long health faucetof approved quality (Jaquar or equivalent)including cost and conveyance complying with standardspecification. |
| 99 | Supply and fixing wall hung type frameless washbasin mirror of approved quality & size of 450mm x 600mm made with 5mm mirror of mounted edges and holes for fixing with threaded type screw / bolt arrangements including cost and conveyance complying with Standard specification. |
| 100 | Supplying,Installing, testing and commissioning of Lipped Mouth Porcelin Flat Back Urinal with all accessories such as 32mm dia Bell mouth PVC connection, 15mm dia G.M. wheel value, 15mm dia \"B\" Class G.I. waste water pipe, 15mm dia nylon connection, 15 mm dia brass nipple etc.,complete as directed |
| 101 | Supply & fixing the following sizes of G.M ball valve of approved quality(ISI) with necessary connection materials connecting the UPVC pipe complying with standard specifications. |
| 102 | 40mm dia G.M gate valve |
| 103 | 25mm dia G.M Ball valve |
| 104 | Supply & fixing RCC precast slab of required size (0.90m × 0.90m) made withconcrete Mix M-20 Grade using 20mm HBG jelly and 8mm TMT rods at a spacing of 150mm c/c, on both direction including cost and conveyance of all materials complying with standard specification. M.H cover |
| 105 | Supply and Erection of \"TEXMO\" make or equivalent 3 H.P open well submersible 3 phase - tSM - 8HZ motor pump size 2 1/2\"\" x 2\"\" delivery with all accessories with suitable concrete bed with bolt & nuts, earth connection, wire connections, testing etc. complete as directed |
| 106 | Providing HDPE (High Density Polyethylene) Buyos Floating Cubes of without wood500mmX500mmx400mm joints together with nylon nuts and bolts. These buyos have anti-skid surface to prevent accidents when the buyos are wet during rains, All parts used in the assembly are metal free . Hence the complete installation is rust free. Charges including for lock oins and nut bolts etc complete 0.5mx 0.5mx 0.4m Module side surface is held together 3dimensionally due to their male female interlocking shape such that they offer much higher pressure resistance and strength in water. 7kg+- 5% More than 350kgper Sq mtr. Dock Is Blow moulded made from High Grade virgin High Density Polyethylene (HDPE). It is AntiSkid. 22mm (± 5%) to ensure sufficient strength. Is made of same material to avoid frictional damage.complying with standard specification. |
| 107 | Anchoring shall be done site specific using 20mm PP rope / chains or 14mm Steel Rope and anchor blocks made of Concrete (250kgs) as per site conditions. Further the jetty shall also be tied to the shore with Steel rope/ chain as indicated in the drawing provided in the tender document.complete as directed |
| 108 | Manufacturing, Supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304 L grade SS pipe of 1.60mm thick t Required locations to a height of 90mm from finished floor level welded to 38mm dia SS post of 1mm thick vertical at 900mm centre with 2 nos of 25mm dia intermediate horizontal SS pipe of 1.60mm thick between. The Vertical pipe has to be welded to the 100 x 100 x 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges etc., completecomplying with standard specification. |
| 109 | Supplying , fabricating and fixing of Mild steel Sections of following sizes ISMB 200 ,MS angle 50x50x6mm ,MSSHS 60x60x4mm with one ocat of primer including cost of labours, materials and transport charges etc.., complete. as directed |
| 110 | Supply, Laying and testing of 1.1KV Grade XLPE insulated, PVC sheathedAluminium / Copper conductor steel armoured power cables as per the specs. The rates quoted shall be for laying in trays, cable trenches (indoor and outdoor), pipes, etc. For buried cables,the excavation work will be includedunder the heading \"Civil works for outdoor cable laying.\" AS PER IS 7098 / IS 1554 |
| 111 | 3 Core x 6 Sqmm Al Ar CABLE |
| 112 | 3 Core x 1.5 Sqmm CU PVC CABLE |
| 113 | 3.5 Core x 50 Sqmm Al Ar CABLE |
| 114 | 4 Core x 4 SqmmCU Ar Cable |
| 115 | 4 Core x 10 Sqmm Al Ar CABLE |
| 116 | Supplying and providing the end terminations with Aluminium / Copper cable lugs, Double compression brass cable glands, taping, crimping, gland and armour earthing, etc. complete as required. |
| 117 | 3 Core x 6 Sqmm Al Ar CABLE |
| 118 | 3.5 Core x 50 Sqmm Al Ar CABLE |
| 119 | 4 Core x 4 SqmmCu Ar CABLE |
| 120 | 4 Core x 10 Sqmm Al Ar CABLE |
| 121 | Wiring with 2x2.5Sqmm FRLS PVC insulated 1100 V grade FRLS copper conductor wires and 1x1.5SqmmFRLS PVC insulated earth wire inFRLS PVC conduits of not less than 20 mm size as per specification titled \"DISTRIBUTION SYSTEM, CONDUITS, WIRING ANDACCESSORIES\". Height of ceiling varies from 3.5 to 4 metres. A separate neutral shall be run for each circuit. Any civil works involved like wall chipping ,plaster and finishing shall be considered and executed to satifaction of enginer in charge .Note: The rates for the following items shall include supply and installation ofModular type of switches, sockets, fan regulators, etc., along with all necessary fixing accessories like mounting screws, concealed/surface mounted switch boxes suitable for modular type switches, internal wiring, top plate, etc., all complete as required. The modular type switches, sockets, regulators shall be of approved make & shade. |
| 122 | Single light point controlled by 6 Amps SP switch |
| 123 | Ceiling Fan Controlled by 10A Switch with Elec. Regulator |
| 124 | Wall Fan Controlled by 10A Switch |
| 125 | 6 Amps, 5 pin ,230V, single phase round pin socket with 6 Amps SP switch |
| 126 | 16 Amps, 5-pin ,230 Volts, single phase round pin socket with 16 Amps single pole switch with indicating LAMP. |
| 127 | Supplying, installation, testing &Commissioningof the following types of light & fan, drivers controlgear, connecting wire withLamps etc. complete as required. |
| 128 | 8 Watts LED Short Garden Lights |
| 129 | 6 Watts LED Ground Level Well Lights |
| 130 | 8 Watts LED light fixture (Track Lights) |
| 131 | 8 Watts LED Height Stone Bollard Lights 8 feet |
| 132 | 3 Watts LED light fixture (COB Spot lights) |
| 133 | 10 Watts LED light fixture (Profile Lights) |
| 134 | 5 Watts LED light fixture (Foot Light Outdoor) |
| 135 | 45 Watts LED Street Light (Single head) |
| 136 | 45 Watts LED Street Light (Double head) |
| 137 | 14 Watts LED light fixture (Celing mounted) |
| 138 | 28 Watts LED light fixture (Tube lights) |
| 139 | Ceiling fan |
| 140 | Wall fan |
| 141 | Exhaust Fan |
| 142 | Wiring for Submain wiring with following sizes of PVC FRLS insulated copper conductor single core wire in surface/recessed PVC conduit as required, including supply of pvc conduit: |
| 143 | 20mm PVC Conduit |
| 144 | 25mm PVC Conduit |
| 145 | 32mm PVC Conduit |
| 146 | Supply and laying of pipes in wall / floor / in ground including chipping / excavation laying and making good the surface as required. Any collars and bends and nipples required shall be laid at a depth of 900 mm below ground level or under paved areas / under floor as required. |
| 147 | 25 mm dia HDPE pipe. |
| 148 | 50 mm dia HDPE pipe. |
| 149 | 25 mm dia Class \"B\" G I pipe. |
| 150 | 100 mm dia Class \"B\" G I pipe. |
| 151 | Supplying, erection, testing and commissioning of 415Volts, 3 phase 50Hz switchboards/panels/PDBs with ACB,MCCB,MCB units as per specification titled \"415 Volts switch Boards\", As per SLD and Specifications complete as required. MAIN PANEL |
| 152 | Supply, store, erection, testing and commissioning of Double Door out door type, LT Feeder Pillar 1 having 1 No 32A 4P MCB as Incomer with 24 Hour Time Switch , 3nos 16A DP RCCB as sub incomer with Contactor for automatic operation and 9 nos 10A SP MCBs as Outgoing. |
| 153 | Supply, store, erection, testing and commissioning of Double Door out door type, LT Feeder Pillar 2 having 1 No 32A 4P MCB as Incomer with 24 Hour Time Switch , 3nos 16A DP RCCB as sub incomer with Contactor for automatic operation and 9 nos 10A SP MCBs as Outgoing. |
| 154 | Supply, store, erection, testing and commissioning of Double Door out door type, LT Feeder Pillar 3 having 1 No 32A 4P MCB as Incomer with 24 Hour Time Switch , 3nos 16A DP RCCB as sub incomer with Contactor for automatic operation and 12 nos 10A SP MCBs as Outgoing. |
| 155 | Supply, store, erection, testing and commissioning of Three Phase Distribution Board having 1 No 32A 4P MCB as Incomer with 24 Hour Time Switch , 3nos 16A DP RCCB as sub incomer with Contactor for automatic operation and 9 nos 10A SP MCBs as Outgoing. |
| 156 | Supply of 3 Phase Auto-Manual Direct On Line Delta 3hp 6-9amp Motor Starter Panel |
| 157 | GST at 18% |
