Tender For Repair/ Renovation Of Lodgement Centers.- 1 Removing dry or oil bound distemper, water proofing cement paint andthe like by scrapping and sand papering and preparing the surface smoothincluding necessary repairs to scratches etc. complete. 2 Distempering with 1st quality Acrylic/oil bound washable distemper(ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as permanufacturers’ specifications, one or more coats on old work 3 Providing and applying white cement based putty of specified thickness,of approved brand and manufacturer, over the plastered wall surface toprepare the surface even and smooth complete.13.88.1 1 mm thick 4 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge 5 Providing and fixing ACP Sheet 3.7mm thick of required thickness of any colour and shade as similar to already attached sheet 6 Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittingsand fixtures complete: 18.19.1 10 liter capacity -White 7 Providing and fixing 15 mm nominal bore C.P. brass bib cock ofapproved quality conforming to IS : 8931 8 Providing and fixing 15 mm nominal bore C.P. brass angle valve forbasin mixer and geyser points of approved make conforming to IS : 8931 9 Providing and fixing of G.I pipes complete with G.I fittings and clamps including cutting and making good the walls etc. internal work 10 Providing and fixing of G.I unions complete with including cutting and making good the walls etc 11 Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge. 12 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 13 Providing and fixing P.V.C. waste pipe for sink or wash basin including Semi rigid pipe40mm dia P.V.C waste fittings complete 14 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm sizes respectively. 15 Providing and fixing uplasticized PVC connection pipe with brass unions 15 mm nominal bore 16 Providing and fixing 100 mm sand cast iron grating for gully trap. 17 Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with ½” BSP thread and shapes, weighing not less than 60 gms 18 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereverrequired:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm 19 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings 20 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour:Waste coupling 38mm of 83 mm length and 77 mm breadthweighing not less than 60gms. 21 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm 22 Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms 23 Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 24 Renewing glass panes, with putty and nails wherever necessary includingraking out old putty Float glass panes of thickness 5.0 mm(weight not less than 12.5kg/sqm 25 Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications:Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacturer 26 Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (twoor more coats) including a coat of approved steel primer but excluding a coat of mordant solution. 27 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and 28 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete 29 Providing and fixing 1st quality ceramic glazed floortiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming of IS :13755 of NITCO, ORIENT, SOMANY, KAJARIA, or equivalent make in all colors, such as white, Ivory, Grey, Fume Red Brown or as approved by Engineer In Charge over 20mm thick bed of cement mortar 1:4 (1 Cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete 30 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement basedpolymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge 31 Engaging of labour for cleaning manhole/drain 32 carriage of materials by mech. Transport Sand av lead 45 km
