Supply And Fixing (Installation) Of Furniture At Jnv Phase-A Howrah (W.B) , School Building , Supply & Installation Big Desk (For Two Persons)-The Overall Dimensions Of Desk Will Be 1066Mm * 930Mm * Height 760Mm, Complete As Perspecifications Enclosed And Direction Of Engineer-In- Charge Having The Table Top Shall Be Made Up Of 18.0 Mm Thick Plywood Is 303 Of Mr Gradeosl (One Side Shall Be Laminated, And Other Side Shall Have Balancer Finish). Table Top Dimensions Shall Be W 850 Mm X D 380 Mm. Edge Towards Benchshall Be Post Formed With Round Edge. The Remaining Three Edges Must Be Sealed With 2Mmthick Pvc Edge Banding Tape. Edge Band Must Be Trimmed On Edges And Corners.Seat And Back Rest Shall Be Made Of 18Mm Thickplywood Of Mr Grade Osl (One Side Shall Be Laminated, And Other Side Shall Have Balancer Finish) Except Back Rest. Back Rest Shall Be Have Both Sidescolour Lamination. Technical Details Of Seat And Back Rest Are Mentioned Below:Seating Bench Dimensions Shall L 900 Mm X W 300 Mm. Front Side Shall Be Rounded Withpost Forming. Remaining Three Edges Shall Sealed With 2Mm Thick Pvc Edge Banding Tape.Back Rest Dimensions Shall L 900 X H 200 Mm Upper Side Shall Be Rounded With Post Forming Remaining Three Edges Shall Be Sealed With 2Mm Thickpvc Edge Banding Tape. Desk Shelve Shall Be Made Of Prime Quality 0.8Mm Thick Crca Sheet Of H150mmxd300mm And Side Stiffeners Of Mscrca Tube Size 19Mmx19mmx1mmthick. One Vertical Support (Partition) Of Square Tube Size 25Mm Square X1.2Mm Thick Must Be Provided At Centre Oftray . Upper Moedsty Made Of Prime Quality 0.8Mm Thick Crca Sheet Powder Coated Should Be Embossed With Dimples In Round Shape, Heightwill Be 150Mm, There Should Be Perforated Lower Modesty Made Of Prime Quality 0.8 Mm Thick Crca Sheet Of Size H150mmxd21mm Withsquare Perforation, Crcat Ube Of Size 19X19x1mm Thick To Be Inserted For Full Length At Bottom Of Jali . Thick Welded To 25Mmx50mmx1.2Mm Thick Crca Tube , Seat And Back Side Frame Structure Made Of Prime Quality Crca Pressed Form Section165mmx25mmx1mm Thick Welded To 25.4Mm Diameter X 1.6Mm Thick Erw-1Pipe , There Will Be 8No. Horizontal Supports Are 25Mmx25mmx1.2Mmthick Crca Pipes.Bottom Rectangular Tube 50X25x 1.2Mm Thick Should Be Closed With Ppcp Cap Bothside Sand Pipe Dia. 25.4X1.6Mm Thick Should Be Closed With Metal(Backside) And Other Side (Undertheseat) Ppcp Cap, Complete As Per Engineer Incharge Desk Should Be In Semi Knock Down Form With The Help16 Connecting Pipes ; 8 Pipes On Each Side : Connecting Pipe Size Will Be 20X20x1.2Mm .All Metal Pieces Shall Be Welded Properly Strongly Andconformity With Regulations With Co2 Welding Shall Be Used , Crca Metal Shall Be Coated After Being Treated With At Least Three Stages Andcleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form A Layer Of Base Coating Of(Iron Phosphating) (0.4 – 0.8) Gm/M² , Automatic Spray Coating Shall Be Applied To Be Followed By A Drying Process In A Thermal Furnace With Suitable Temperature And Time For The Process , Metal Pipe & 7 Tank Treatment With Minimum 45-50 Micron Powder Coating . , Supply & Installation Medium Desk (For Two Persons)-The Overall Dimensions Of Desk Will Be 900Mm W± 5 X 890Mm D± 5 X 688/420Mm H± 5 , Complete As Per Specifications Enclosed And Direction Of Engineer-In- Charge Having The Table Top Shall Be Made Up Of 18.0 Mm Thick Plywood Is 303 Of Mr Grade Osl (One Side Shall Be Laminated, And Other Side Shall Have Balancer Finish). Table Top Dimensions Shall Be W 850 Mm X D 380 Mm. Edge Towards Bench Shall Be Post Formed With Round Edge. The Remaining Three Edges Must Be Sealed With 2Mmthick Pvc Edge Banding Tape. Edge Band Must Be Trimmed On Edges And Corners.Seat And Back Rest Shall Be Made Of 18Mm Thick Plywood Of Mr Grade Osl (One Side Shall Be Laminated, And Other Side Shall Have Balancer Finish) Except Back Rest. Back Rest Shall Be Have Both Sides Colour Lamination.Technical Details Of Seat And Back Rest Are Mentioned Below:Seating Bench Dimensions Shall L 900 Mm X W 300 Mm. Front Side Shall Be Rounded With Post Forming. Remaining Three Edges Shall Sealed With 2Mm Thick Pvc Edge Banding Tape. Back Rest Dimensions Shall L 900 X H 200 Mm Upper Side Shall Be Rounded With Post Forming Remaining Three Edges Shall Be Sealed With 2Mm Thick Pvc Edge Banding Tape. Desk Shelve Shall Be Made Of Prime Quality 0.8Mm Thick Crca Sheet Of H150mmxd300mm And Side Stiffeners Of Ms Crca Tube Size 19Mmx19mmx1mmthick. One Vertical Support (Partition) Of Square Tube Size 25Mm Square X1.2Mm Thick Must Be Provided At Centre Of Tray . Upper Moedsty Made Of Prime Quality 0.8Mm Thick Crca Sheet Powder Coated Should Be Embossed With Dimples In Round Shape, Height Will Be 150Mm, There Should Be Perforated Lower Modesty Made Of Prime Quality 0.8 Mm Thick Crca Sheet Of Size H150mmxd21mm With Square Perforation, Crcat Ube Of Size 19X19x1mm Thick To Be Inserted For Full Length At Bottom Of Jali . , Supplying And Installation Of Site Knock Down Type Office Table As Per Approved Design And Directrion Of Engineer-In-Charge.Work Top - Work Top Shall Be Made 25Mm Thick Pre-Laminated Mdf Board With Decorative Lamination On One Side And Balancing Lamination On Other Side Confirming To Is 12406:2003 With Post Forming On Front, Back And Machine Pressed Pvc Egde Banding 2Mm Thick Glued With Industrial Adhesive And Diffused With Board Monolithically On Other Two Sides. Table Top Shall Have 75Mm Overhung On Front And 25Mm Overhung On Sides. Understructure- C-Type Leg Shall Be Made Of Tubular Section Of 50Mm X 50Mm X 1.6Mm (Wall Thickness) Thick Vertical Member And40mm X40mm X1.6Mm (Wall Thickness) Horizontal M.S. Pipe Confirming Is-Grade 4932 Shall Be Finished With Epoxy Polyster Powder Coated Dft 50-60 Micron. The Legs Shall Be Fitted To The Ground With M8 Screw Leveler With The Height Adjustment Up To 15Mm. The Cross Members Shall Be Mounted By End Brackets Made Of 3Mm Thick Crca Steel Sheet Confirming Is 513: 2008And Finished With Epoxy Polyster Powder Coated Dft 50-60 Micron Confirming Is 13871:1993.Wire Management - Electrical Wires Shall Be Carried From Horizintal/ Vertical Duct Made Of 0.7Mm Crca Steel Sheet Confirming To Is 513:2008. The Switch Plate Or Grommet Depending Upon Requirement Shall Also Be Provided For Electrical/Lan Connection On Table Top.Modesty Panel -Modesty Panel Of Height 450Mm Shall Be Made Of 1.5Mm Thick Crca Sheet Sheet Confirming To Is 513: 2008And Shall Be Finised With Epoxy Polyster Powder Coated Dft 50-60Micron. Storage Body- Storage Top Shall Also Be Made Of 25Mm Thick Pre-Lam Mdf Board Confirming To Is 12406:2003 With Post Forming On Two Sides And Machine Pressed Pvc Egde Banding 2 Mm Thick Glued With Industrial Adhesive And Diffused With Board Monolithically On Other Two Sides. The Body Of Storage Unitsshall Be Made Of 0.8Mm Thick Crca Steel Sheet And Skirting Shall Be Of 1.2Mm Thick Crca Steel Sheet Confirming To Is 513: 2008 Finished With Epoxy Powder Coated Of Dft 50-60 Micron Confirming Is 13871:1993. Internal Shelves Shall Be Also Made Up Of 0.8Mm Crca Steel Sheet Confirming To Is 513: 2008 And Shall Be Mounted With The Metal Shelf Support Pin Made Of 2Mm Thick Crca Steel Sheet With Nickel Or Chrome Plating.M10 Screw Leveler Is Given With Height Adjustment Up To 12Mm To 15Mm. , Table Of Size 1800Mm (W) X 750Mm (D) X 750Mm (H) With Side Storage Of Size 900Mm (W) X 450Mm (W) X 750Mm (H) And Back Storage 1800Mm (W) X 450Mm (D) X 750Mm (H) , Table Of Size 1650Mm (W) X 750Mm (D) X 750Mm (H) With Side Storage Of Size 900Mm (W) X 450Mm (W) X 750Mm (H) And Back Storage1650 Mm (W) X 450Mm (D) X 750Mm (H) , Office Table With Overall Size Of Desk 1350Mm (L) X 750Mm (W) X 750Mm (H)& Side Storage Unit Of Size 900Mm (L) X 450Mm (W) X 750Mm (H) , Supplying And Installation Of Knock Down Type Office Table Made Of Pre-Laminated Mdf Board With Decorative Lamination On One Side And Balancing Lamination On Other Side Top Of Size 1199 X 590 X 735 Mm. Worktop Shall Be Rounded In All Four Corners And Should Have An Overhung Of 50Mm Alongwith One Drawer Unit Made Of 0.5Mm Thick Crca Steel Sheet. The Table Top Shall Be Supported Over Legs Consists Of Ms Erw Round Tube Of 25Mm Dia X 1.2Mm (Wall Thickness) And Cross Horizontal Members Including Leg Rest Of 25Mm Dia X 1.2Mm (Wall Thickness) M.S. Erw Tube. All Steel Components Be Shall Be Finised With Epoxy Polyster Powder Coated Dft 50-60Micron. , Supplying And Installation Of Knock Down Type 12 Seater Meeting Table Of Of Overall Size 3600 X 1350 (Maximum) X 750 Mm (Knock Down Type). Table Top Shall Be Made Of 25Mm Thick Pre-Laminated Partical Board With Decorative Lamination On One Side And Balancing Lamination On Other Side Whereas The Gable Ends Shall Be Of 25Mm Thick Pre-Laminated Partical Board With Decorative Lamination On Bothside Alongwith 2Mm Thick Machine Pressed Pvc Edge Banding Glued With Industrial Adhesive And Monolithically Diffused. Supporting Understructure Consists Of2 Metal C Legs On Either Ends Of Table Support Frame Made Of 50Mm X 50Mm X 1.6 Mm (Wall Thickness) Ms Erw Tube And One Number Wire Carrier Leg At Middle Of 50Mm X 50Mm X1.6Mm (Wall Thickness), 4 Numbers Horizontal Connector Of 40Mm X 40Mm X 1.6Mm Thick Ms Pipe Between Supportingvertical Legs.All The Ms Pipes And Sheetshall Be Finished With Epoxy Powdercoated Of Dft 50-60Micron. The C Typed Metal Legs Shall Be Kept 150Mm Inside From Outer Edge Of Table Top. Agement -The Vertical (Stake) & Horizontal (Cable Tray) Wire Carriers Are Placed Below Worktop, Made Up Of Crca Steel Sheet With Epoxy Powder Coating & Fixed To The Understructure With Specially Designedbrackets, Includingprovision Of Placing Switch Plates/Grommet In The Cable Tray . , Supplyand Installation Of Library Table In Sizes Of 2400Mm (L)X 900Mm (W) X 750Mm (H) Consisting Of Follwing Specification:- Work Top - Work Top Shall Be Made Of 25Mm Thick Pre-Laminated Partical Board With Decorative Lamination On One Side And Balancing Lamination On Other Side Confirming To Is 12823: 1990, Alongwith 2 Mm Thick Machine Pressed Pvc Edge Banding Glued With Industrial Adhesive And Monolithically Diffused With Board On Exposed Edges.Understructure Supporting Frame Shall Consists Ofthree Metal C-Legs (Two At Either Ends And One In Middle Of Table) And Joined By Two Numbers Horizontal Connector Made Of Tubular Section 40Mm X 40Mm X 1.6Mm (Wall Thickness) Confirming To Is 4923:1997.The Entire Metalframe Shall Be Finised With Epoxy Polyster Powder Coated Dft 50-60 Micron. C-Typed Metal Legs Shall Be Kept 150 Mm Inside From From End Of Table. Legs Shall Be Fitted To The Ground With M8 Screw Leveler With The Height Adjustment Up To 12Mm To 15Mm. , Supplying And Installation Of Knock Down Type Dual Computer Work Station Of Unit Size 1500Mm (L) X 600M (W) X 750Mm (H) For Two Students Work Top- Work Top Shall Be Made 25Mm Thick Prelam Particle Board With Decorative Lamination On One Side And Balancing Lamination On Other Side Confirming To Is 12823: 1990 With 2Mm Thick Machine Pressed Pvc Edge Banding Glued With Industrial Adhesive And Monolithically Diffused With Board On All Sides. Understructure Supporting Frame Consist Of 2 Metal C Legs On Either Ends Of Table Support Frame Made Of 50Mm X 50Mm X 1.6 Mm (Wall Thickness) Ms Erw Tube And One Number Wire Carrier Leg At Middle Of 50Mm X 50Mm X1.6Mm (Wall Thickness), 4 Numbers Horizontal Connector Of 40Mm X 40Mm X 1.6Mm Thick Ms Pipe Between Supportingvertical Legs. The Ms Pipes Shall Be Finished With Epoxy Powdercoated With Dft Of 50-60 Micron Confirming To Is 13871:1993. The Legs Shall Be Fitted To The Ground With M8 Screw Leveler With The Height Adjustment Up To 15Mm. Wire Management-The Vertical /Electrical Duct & Horizontal Cabletray ( Wire Carriers) Aremadeof Crca Steel Sheet & Fixed To The Understructure Below Worktop With Specially Designedbrackets. Provision For Fixing Switch Platesare Prividedin The Cable Tray For Easy Access Through Wire Mangaer Or Pvc Grommet. Screens / Privacy Panel: - Screen Height Will Be 300Mm Above Work-Top Made Of Prelam Particle Board/White Board Alternatively As Approved By Engineer-In-Charge. In Addition Privacy Panel Of 300 Mm Height, On Work Top, Shall Be Provided Between Two Workstation. , Supply And Installation Of Glass-Door Storage Of Size 916 Mm (W) X 486Mm (D) X 1980Mm (H). It Should Have Shelf Thickness Of 0.7Mm, Back Thickness Of 0.8Mm, Door Thickness Of 0.8Mm (High Yield Strength) With Clear Glass Of 3.0Mm Thick And All Other Components Shall Have A Thickness Of 0.9Mm. These Components Shall Be Made Of Crca Steel Sheet ‘D’ Grade High Yield Strength As Per Is 513:2008 The Glass Door Storwel Shall Have A Ss Handle And A Two-Way Locking Mechanism With Shooting Bolt. It Should Have A Height-Wise Adjustable Shelf Mounting Which Shall Have A Uniformly Distributed Load Capacity Of Max 40 Kg. It Should Also Have A M10 Screw Type Leveller With Hex Plastic Base.All Metal Components Would Be Epoxy Polyster Powder Coated Dft 50-60 Micron Confirimg To Is 13871:1993 , Overall Size 900Wx300dx2100hmm,Top Made Up Of 18Mm Thick Postlam Plywood With Pvc Edge Banding ,Side Panel Made Up Of 18Mm Thick Postlam Plywood With Pvc Edge Bending , Skirting Made Up Of 18Mm Thick Postlam Plywood With Pvc Edge Bending ,Back Panel Made Up Of 18Mm Thick Postlam Plywood , One Number Of Drawer As Per Ref.Image ,Shelf Made Up Of 18Mm Thick Postlam Plywood With Pvc Edge Bending, All Wooden Panels Fix Joints With Minifix Dowels & Other Fitting Equipment , All Wooden Panels Prime Quality Board With Isi Marked. Complete Structure Design Should Be As Per Reference Image Only. , Supply Adn Installation Of Lab Stool Seat Revolving Stool With Backrest Overall Dimension: 410W ±10 X 410D ±10 X 820H ±10 Mm,Seat Of Chair Is Made Of 12Mm Thick Hot Pressed Plywood Pasted With High Densitypu Foam & Leatherette Upholstery, Back Is Made Of 12Mm Thick Hot Pressed Plywood Pasted With Pu Foam D -40 Kg/M3 , H-20 Seat And Back Fixed Through Metal Powder Coated Spine Covered With Plastic Cover, Seat Size: 400W ±10X 400D ±10 X 75Thick. ±5 Mm, Back Size: 450W ±10 X 240H ±10 X 50Thick. ±5Mm ,Ground To Seat Height-440-560Mm,Mechanism:- Machanism Design With Features Of Revolving At 360 Degree .Machanism Provided Upright Position Locking,Seating Height Can Be Adjusted With A Pneumatic Gas Lift,Gaslift: Lift -Used Gaslift Of 90 Mm Size Of Class-Iv Grade With Plastic Bellow Cover,Chair Base & Wheels: Metal Chrome Plated Chair Basemade Of 2.5Mm Thick Metal Chrome Plated Steel Frame, Base Consists Of 5 Prongs With 560±5 Mm Pitch Circle Diameter, 50Mm Dia. Black Nylon - Twin Wheel Pin Castor . , High Back Revolving Chair, Overall Dimension:- 700W ±10 X 700D ±10 X 1210H ±10 Mm,Seat Of Medium Back Chair Is Made Of 12Mm Thick Hot Pressed Plywood Pasted With Pu Moulded Foam With Fabric Upholstery On Seat,Used Pu Moulded Foam On Seat Of D-45 Kg/M3 , Back Ofchair Is Made Of Injection Moulded Pp Material Structure Upholstered With Mesh Fabric , Adjustable Lumber Support Upholstered With Fabric , Adjustable Headrest On Back Upholstered With Mesh Fabric ,Seat Size:- 470W ±10 X 460D ±10 X 70Thick. ±5 Mm , Back Size: 500W ±10 X 780H ±10,Mechanism:- The Synchro Tilt Mechanism ,Used Gaslift Of 90 Mm Size Of Class-Iv Grade,Armrest:- Pu Padded Adjustable Armrestfixed With Seat ,Chair Base & Wheels: Ms Chrome Plated Base Consists Of 5 Prongs With 640±5 Mm Pitch Circle Diameter, 50Mm Dia. Black Nylon - Twin Wheel Pin Castor . , Medium Back Revolving Chair, Overall Dimension:- 720W ±10 X 720D ±10 X 1070H ±10 Mm,Seat Of Medium Back Chair Is Made Of 12Mm Thick Hot Pressed Plywood Pasted With Pu Moulded Foam With Fabric Upholstery On Seat , Used Pu Moulded Foam On Seat Ofd-45 Kg/M3 , Back Of High Back Chair Is Made Of Injection Moulded Pp Material Structure ,Combination Of Upholstered With Mesh Fabric , Seat And Back Connected Through Metal Powder Coated Plate, Adjustable Lumber Support Upholstered With Fabric , Seat Size:- 470W ±10 X 470D ±10 X 70Thick. ±5 Mm , Back Size: 525W ±10 X605h ±10,Mechanism:- The Synchro Tilt Mechanism ,Used Gaslift Of 90 Mm Size Of Class-Iv Grade,Armrest: Pu Padded Adjustable Armrest Fixed On Frame,Chair Base & Wheels: Metal Chrome Plated Chair Base Consists Of 5 Prongs With 650±5 Mm Pitch Circle Diameter, 50Mm Dia. Black Nylon - Twin Wheel Pin Castor. , Fixed Visitor Chair, Overall Dimension:- W600±10 X 600D ±10 X 890H ±10 Mm,Seat Of Medium Back Visitor Chair Is Made Of 12Mm Thick Hot Pressed Plywood Pasted With Pu Moulded Foam With Fabric Upholstery On Seat , Used Pu Moulded Foam On Seat Of D-45 Kg/M3, Back Of Medium Back Chair Is Made Of Injection Moulded Pp Material Structure With Mesh Fabric, Seat Size:- 460W ±10X 470D ±10 X 60Thick. ±5 Mm , Back Size:- 440W ±10 X 470H ±10,Armrest:- Fixed Pp Armrest ,Understructure:- Cantilever Frame Made Powder Coating Ofround Pipe 14 Gauge Thickneess With Plastic Bushes . , Medium Back Revolving Chair, Overall Dimension:- 700W ±10 X 700D ±10 X 1010H ±10 Mm,Seat Of Medium Back Chair Is Made Of 12Mm Thick Hot Pressed Plywood Pasted With Pu Moulded Foam With Fabric Upholstery On Seat ,Used Pu Moulded Foam On Seat Ofd-45 Kg/M3 , Back Of Chair Is Made Of Injection Moulded Pp Material Structure Combination Of Upholstered With Mesh Fabric , Seat And Back Connected Through Metal Powder Coated Plate Having Adjustable Lumber Support Upholstered With Fabric , Seat Size:- 490W ±10 X 450D ±10 X 70Thick. ±5 Mm , Back Size: 525W ±10 X640h ±10,Mechanism:- The Synchro Tilt Mechanism ,Used Gaslift Of 90 Mm Size Of Class-3 Grade,Armrest: Pu Padded Adjustable Armrest,Chair Base & Wheels: Revolving Pedestal Nylon Base Consists Of 5 Prongs With 640±5 Mm Pitch Circle Diameter, 50Mm Dia. Black Nylon - Twin Wheel Pin Castor . , Supplying And Installation Of Metal Lockers With Cam Lock One Unit Consiting Of 381Mm (W) X 381Mm (D) X 1831Mm (H) With 4 Lockers. Body-Lh And Rh Side And Back Panel Is Made Up Of 0.8Mm Thick Crca Steel Sheet Confirming To Is 513:2008 Which Is Having Standard Dimension 1831 X380mm. Shelf Hanging Bracket Is Welded On Both The Side Panel By Spot Welding. Shelf Hanging Bracket Is Made Up Of 0.8Mm Thick Crca Steel Sheet Confirming To Is 513:2008. Front Frame, Top And Bottom Part Made Up 0.8Mm Thick Crca Steel Sheet Confirming To Is 513:2008 And Horizontal Part Is Made Up 1Mm Thick Crca Steel Sheet Confirming To Is 513:2008. On A Front Frame Horizontally Provision Is Given At A Common Distance To Hold Shutter Bracket. Locker’S Top Is Made Up Of 0.8Mm Thick Crca Steel Sheet Confirming Is 513:2008 Which Is Having Standard Dimension 375 X378mm. Shelf Is Also Made Up Of 0.8 Mm Crca Steel Sheet Confirming To Is 513:2008.Shutter- Is Made Up On 0.7Mm Thick Crca Steel Sheet Confirming To Is 513:2008. All The Shutter Are Hung On Shutter Pin And Shutter Bracket, Louvers Are Given In Shutter For Air Flow. Pvc Flush Handle And Name Plate Is Used For Handling And For Name Plate Tagging. Standard Locking Arrangment Is Used For Locking Each Shutter.The Bodies Including Shelves Are Given Anti-Rust Surface Treatment & Are Powder Coated With Epoxy Polyester Powder Coating Of Dft 50-60 Micron Confirimg To Is 13871:1993. , 1.Dimensions And Configuration Total Width Of The Setup: Minimum 12 Feet. Height: Approximately 4 To 4.5 Feet From The Board Surface. 2.Sliding Boards: Quantity: 2 (Left And Right). Size (Each Board): 6 Feet (W) × 4 Feet (H) 3.Material: Left: Green Chalkboard (Matte Surface, Suitable For Chalk) Right: Whiteboard (Glossy Surface, Suitable For Dry-Erase Markers) 4.Function: Boards Shall Slide Horizontally On A Top And Bottom Aluminum/Steel Channel Track To Fully Cover Or Reveal The Ifp As Needed. 5. Interactive Flat Panel (Ifp) Position: Centered Within The Frame And Between The Two Sliding Boards. Mounting: Wall-Mounted Securely Inside The Board Structure, With Space Allowance For Ventilation And Service Access. Ifp Opening Size: Sized Appropriately To The Ifp Being Installed (Contractor To Confirm Model And Dimensions). 6.Frame Material: Laminated Plywood Or Mdf With A Natural Wood Finish Or Laminated Color Finish (As Per Architect/Owner Approval). 7. Frame And Track System Material: Aluminum Or Powder-Coated Steel Tracks With Smooth Sliding Mechanism. Top & Bottom Rails: Tracks Shall Be Aligned And Reinforced To Ensure Boards Move Easily And Without Wobble. Finish: Durable, Corrosion-Resistant Coating Suitable For Indoor Use. 8.. Additional Requirements All Boards And The Structure Must Be Securely Fixed To The Wall With Appropriate Fasteners. Provision For Cable Management Must Be Included For The Ifp (I.E., Concealed Conduit/Path For Power And Data Cables). The Unit Must Be Free From Sharp Edges, Splinters, Or Any Protruding Parts That Could Cause Injury. Installation Height Should Ensure Comfortable Writing Access For Average Adult And Student Height (Typically Bottom Edge ~2.5 To 3 Feet From The Floor). , Supply And Installation Of Physics Along The Wall Lab Table Of Size1800(L) X 750(W) X 860(H)(9 No)With Specification As Under: Overall Size 1800W X 750D X 850H.Storage Box Size 1800W X 750D X 850 . Physics Island Lab Table Of Size1800(L) X 1500(W) X 860(H)(2 No)With Specification As Under:Overall Size 1800W X 1500D X 850H.Storage Box Size 1800W X 1500D X 850.Box Of Storage( 1D + 2S ).Storage Per Box Size Without Granite600w X 570D X 713H Using 100Mm Pvc Leg Supported .Storage Upper Top 19Mm Thick Granite Top All Joints Will Be Filled With Silicon Sealent. The Material Must Be 18 Mm Plywood With Mica At All Sides. , Supply And Installation Of Chemistry Along The Wall Lab Table Of Size1800(L) X 750(W) X 860(H)(9 No)With Specification As Under: Overall Size 1800W X 750D X 850H.Storage Box Size 1800W X 750D X 850H1 X 1550H2 . 1 Nos. Reagent Racksize 1300W X 300D X 700H. Chemistry Island Lab Table Of Size1800(L) X 1500(W) X 860(H)(2 No)With Specification As Under:Overall Size 1800W X 1500D X 850H.Storage Box Size 1800W X 1500D X 850H1 X 1550H2 . 1 Nos. Reagent Racksize 1300W X 300D X 700H. Box Of Storage( 1D + 2S ) 0.8Mm Ms Sheet Powder Coated.Storage Per Box Size Without Granite600w X 570D X 713H Using 100Mm Pvc Leg Supported .Storage Upper Top 19Mm Thick Granite Top All Joints Will Be Filled With Silicon Sealent.The Material Used Must Be 18 Mm Plywood With Mica At All Sides , Supply And Installation Of Biology Along The Wall Lab Table Of Size1800(L) X 750(W) X 860(H)(9 No)With Specification As Under: Overall Size 1800W X 750D X 850H.Storage Box Size 1800W X 750D X 850H1 X 1550H2 . 1 Nos. Reagent Racksize 1300W X 300D X 700H. Biology Island Lab Table Of Size1800(L) X 1500(W) X 860(H)(2 No)With Specification As Under:Overall Size 1800W X 1500D X 850H.Storage Box Size 1800W X 1500D X 850H1 X 1550H2 . 1 Nos. Reagent Racksize 1300W X 300D X 700H. Box Of Storage( 1D + 2S ) 0.8Mm Ms Sheet Powder Coated.Storage Per Box Size Without Granite600w X 570D X 713H Using 100Mm Pvc Leg Supported .Storage Upper Top 19Mm Thick Granite Top All Joints Will Be Filled With Silicon Sealent. The Material Used Must Be 18 Mm Plywood With Mica At All Sides. , Kitchen & Dining , Dining Table: Ss Dinning Table Consists Of Dinning Top Is Made Up Of 1 Mm Thickness Stainless Steel Sheet Of Ss 304 Grade With Overall Dimension Of 1800(L) X 700(D) X 750(H). The Table Top Is Reinforced With A 18 Mm Ply Board On Stainless Steel Frame Of Square Section 40Mmx40mmx1.6Mm. Dinning Top Of Stainless Steel Sheet Shall Be Extended To The Sides And A Depth Upto 40 Mm Under The Table Top In All Directions Includingedge Rounding, Grinding And Finishing Etc. All Complete. The Table Top Shall Finish In Such A Manner To Avoid Any Sharp Edges. The Table Will Be Supported By Four Hollow Legs Made From Ss 304 Grade Stainless Steel. The Hollow Legs Shall Be Of Square Type Of Size 50Mmx50mmx1.6Mm. These Legs Shall Be Securely Welded Or Mechanically Fastened To The Underside Of The Tabletop Frame. For Additional Structural Stability, Stainless Steel Cross Supports Shall Be Provided Between The Legs As Shown In Figure With 40Mmx40mmx1.6Mmss Square Section. The Table Shall Include Rubber Shoes At The Bottom Of Each Leg To Prevent Floor Damage And Ensure Stability. The Design Shall Prioritize User Safety With No Sharp Corners Or Edges. The Table Must Be Structurally Sound And Capable Of Supporting A Uniformly Distributed Load Of At Least 250 Kg. All Materials Used Must Conform To Relevant Is Standards, And The Finished Product Should Be Free From Burrs, Dents, Or Deformities , Dining Bench: The Bench Shall Be Of Size 1800 Mm In Length, 300 Mm In Depth, And 450 Mm In Height, Suitable For Use In Residential Schools. The Bench Top Shall Be Made Of 18 Mm Thick Plywood + Laminated , Finished With A 0.8 Mm Thick Decorative Laminate On The Top Surface, And A Balancing Laminatebacking On The Underside To Ensure Dimensional Stability. All Exposed Edges Shall Be Sealed With Pvc Edge Banding Or Machine-Finished To Prevent Splinters And Enhance Durability. The Plywood Shall Be Scratch-Resistant, Water-Resistant, And Easy To Clean, With A Light Woodgrain Or Equivalent Finish As Approved. The Supporting Frame Shall Be Fabricated Frame Of Square Section 40Mmx40mmx1.6Mm Ms Pipe In Powder Coated. These Legs Shall Be Securely Welded Or Mechanically Fastened To The Underside Of The Benchtop Frame. The Bench Shall Include Rubber Shoes At The Bottom Of Each Leg To Prevent Floor Damage And Ensure Stability. The Design Shall Prioritize User Safety With No Sharp Corners Or Edges. The Bench Must Be Structurally Sound And Capable Of Supporting A Uniformly Distributed Load Of At Least 250 Kg. All Materials Used Must Conform To Relevant Is Standards, And The Finished Product Should Be Free From Burrs, Dents, Or Deformities , Boys & Girls Dormitories , Providing And Installing 18 Mm Hdhmr Boards On Existing Rcc And Cement Plasterbrick Walls With The Help Of Counter Sink Fasteners In Plump And Level. All Edges To Be Rounded. 1Mm Laminated Should Be Pasted On All Visible Areas And Edges Polished To Match The Laminate Shade.
