Tender For Addn/Altn To Main Gate No. P-32/J At Palampur Mil Stn; 1 Excavation post holes (or similar holes) in any type of soil each n exc 0.50 cu.m,getting out,returning,filling on and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed. 2 M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed. 3 S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE) 4 M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with selftapping screws as specified. (Colour as approved by GE) 5 S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed. 6 M&L rolled mild steel sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates etc. (Fe-410W Gde-E-250) quality A complete all as specified and directed. 7 S&F framed work as in doors or gates of angle or other section with gusset plates,rails, braces, etc., complete,drilling for fixing of steel sheeting or other covering. doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rail and guides) and hanging;also fastening and fixing conform to Fe-290 Gde E-165 complete all as specified & directed. 8 S&F rolled mild steel sections like angle, channel, flat etc as inframed work such as grills, gratings,etc,with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders ; framed balusters; walk ways; railings; framed work of water tanks and similar work confirming toFe-290Gde E-165 complete all as specified & directed by Engineer-in-charge. 9 S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,without any attachment (Fe-410-W Gde-E-250) complete all as specified and directed. 10 M&L preparation of new surfaces of steel of any description, over 10 cm width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed. 11 S&F aluminium composite panel (ACP) sheet 3mm thick aluminium layered any approved colour fixed to ceiling, walls or any position fixed as per manufacturers instructions including taking down sheets complete all as specified and directed. 12 M&L brick work with sub class B bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed. 13 Taking down cement plaster of any description and any thickness on brick/stone/concrete surfaces scrubbing down with water etc complete all as specified and directed. 14 M&L 15mm thick plaster in CM 1:4 on brick surfaces on concrete surface, as on internal surfaces, finished the surface even and smooth without using extra cement complete all as specified and directed. 15 M&L 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 16 M&L prelaminated WPC board of thickness 18/19mm, interior grade, prelaminated one side decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. 17 S&F wooden lipping of size as required complete all as specified and directed. 18 S&F 40 mm size (Width of flaps when open) continuous paino hinges, mild steel, bright finish or electrogalvanisedcomplete all as specified & directed. 19 M&L magnetic catcher of suitable size as required and as directed. 20 S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified and directed. 21 Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition), including removal of demolished material out of defence premises complete all as specified and directed. 22 M&L RCC nominal mix (1:1.5:3) type A-1 using 20mm graded crushed stone aggregate as in roof slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. 23 M&L RCC nominal mix (1:1.5:3) type A-1 using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. 24 Form work to rough finished surfaces of concrete for soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. 25 Formwork to sides of rough finished concrete surface of foundations, footings, bases of columns, raft and raft beams, sides and soffits (in any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 26 S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 27 S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 28 M&L distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gm/lire of approved manufacturer of required shade and colour complete as per manufacturers specification two or more coats over 2mm wall care putty on old surface of wall including preparation of surfaces complete all as specified and directed. 29 M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/liter and UV resistance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter/10 sqm over and including priming coat of exterior primer applied @ 0.90 liter/10 sqm over new surfaces of wall complete including preparation of surfaces of walls complete all as specified and drected. 30 Dismantling of wall & ceiling boards (fiber, pulp, insulation etc) or insulation boards /slabs /blanketsany thickness, including cover fillets complete all as specified and directed. 31 S&F in repairs aluminium anodised frame/chowkhat for doors, windows, ventilators with minimum thickness of powder coating 50 micron with one or more rebates including joining cleats for fixing etc complete all as specified and directed. 32 S&F powder coated anodised aluminium door shutters (powder coating of any colour and thickness not less than 50 micron) aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprane packing two number of aluminium handle 150mm long for each shutter, one aluminium door stopper, hinges type B-21, 100mm long, anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified and directed. 33 S&F powder caoted anodised aluminium window and ventilator shutters (powder coating of any colour and thickness not less than 50 micron) side hung type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene pakcing one number of aluminium handle of suitable size for each shutter, one peg stays 150mm long, 02 numbers hinges type B-21, 100mm long, anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified and directed. 34 S&F in repairs 4mm thick sheet glass ordinary quality, exceeding 0.50 square metre in each pane fixed with rubber gasket and aluminium powder coated snap beading etc. complete all as specified and directed. 35 Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc. 1.5 sq.m each complete all as specified and directed. 36 S&F 35mm thick factory made 2nd class hard wood rail and styleplain framed, panelled shutter with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board withcommercial veneering on both faces. The size of rail and style as per IS:1003 (part 1) kiln seasoned and chemically pressure treated complete all as specified and directed. 37 Prepartion of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. 38 M&L providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, inculding fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. 39 S&F insignia of Div sign with black background fibre sheet (size of each sheet exceeding 0.49sqm or as required) with S/S Dah Sign (height of sign not less than 400mm) incl necessary fixing as directed complete all as specified and directed. 40 S&F corrosion resistance S/S alphabets letters (height of letters not less than 400mm) fixed over wall at any height with necessary fittings incl fabrication as required and taking down old letters as directed complete all as specified and directed. 41 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 42 M&L coloured tiles of size 400mm x 400mm x 12mm laid in floor over 15mm screed bed in CM 1:4 with grey cement and pigment, any shape and size complete all as specified and directed. 43 M &L non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles each tile exceeding 0.11sqm but not exceeding 0.18sqm, as in flooring, Set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed. 44 M&L 25mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in floor finished the surface even and rough to receive the topping layer complete all as specified and directed. 45 M&L Glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/450mm x 350mm x 7mm thick set and jointed in neat cement slurry,pointed in white or coloured cement to match the colour of tiles, over and including 10mm thick backing coatin CM 1:4 to receive tiles,complete all as specified and directed. 46 M&L providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvative, jointed with cement mortar 1:3 including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage wherever required complete all as specified and directed. 47 M&L new concrete surfaces of any description not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 48 M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub floors, sub-bases, floors and pavings etc. complete all as specified and directed. 49 M&L providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 50 M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed. 51 Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed. 52 Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all asspecified and directed. 53 Taking down un-serviceable sub main wiring of any type and any size from wall, ceiling etc. complete all as specified and directed. 54 M&L for replacement point wiring with 1.5 Sqmm PVC (FRLS-H) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLSH) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing N capping double lock type to be fixed with the help of rawal plugs & screws incl all fittings such as Tee, connector pieces, L-junction etc on joints including Modular GI sheet Metal flush boxes of anyway(as per site requirement) for mounting switches, sockets, regulators etc for fixing one light/fan/bell point/fan/exhaust fan controlled by one 5/6 A switch and making good disturbed surfaces with CM (1:4) to match with the existing whitewash color surface complete all as specified and directed. Notes : (a) Wiring shall be done by using proper colour coding.(b) Earth wire shall be of green colour. 55 Description all as per serial item No 54 here-in-before but one 5pin, 6 Amp socket outlet on same boardcomplete all as specified and directed. 56 Description all as per serial item No 54 here-in-before but one 5pin, 6 Amp socket outletindependent complete all as specified and directed. 57 Description all as per serial item No 54 here-in-before but for one 5 pin socket outlet 16 Amps on independent board with cables 2.5 sqmm for phase and earth wire of size complete all as specified and directed. 58 All as per the description of serial item no 54 above controlled by two2-way switches, with cables 1.5sqmm size all as specified and directed. 59 S&F Modular Switch two way 6 Amp, one module 240 volts ISI marked complete all as specifiedand directed. 60 S&Fbell, AC 230 Volts, single pole complete all as specified and directed. 61 S&F modular bell push 6A 1 module240 volts ISI marked complete all as specifiedand directed. 62 S&F modular Switch one way 6 Amp, one module 240 volts ISI marked complete all as specifiedand directed. 63 S&FSocket, 6A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed. 64 S&F Socket 6A/16A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed. 65 S&F Modular switch 1 way 16 A, 1 module, 240 volts ISI marked complete all as specified and directed. 66 S&F Modular Fan step regulator, 120W 1 module, 240 volts ISI marked complete all as specified and directed. 67 S&F Modular white cover plate 8M complete all as specifiedand directed. 68 S&F Modular white cover plate 6M complete all as specifiedand directed. 69 S&F Modular white cover plate 3M complete all as specifiedand directed. 70 S&F Modular white cover plate 1M complete all as specifiedand directed. 71 S&FSingle pole and neutral enclosure with 1 two pin and earth plug and a socket complete with one single pole MCB, 20 Amp, 240 volts ISI marked complete all as specifiedand directed. 72 S&Fceiling rose, 3 terminal surface type complete all as specifiedand directed. 73 S&F angle lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittingscomplete all as specified and directed. 74 S&F Decorative ultra slim LED Tubelight fitting of LEDwith extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor forelectrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. 75 S&F Decorative ultra slim LED Tubelight fitting of LEDwith extruded polycarbonate, enviormental friendly energy efficient ready to use, 10 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor forelectrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. 76 S&F in replacement post top lantern with 20 watt LED bulb holder type 230 volts AC outdoor type with decorative post top suitable to fixed in and including 32/40mm dia GI pipe for 360 degree indrect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. 77 S&F LED flood light fitting 70 watt 230V outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver lamp bracket IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. 78 S&F LED flood light fitting 120 watt 230V outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver lamp bracket IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. 79 S&F street light bracket made out of 32mm dia GI light grade tubing not less than 1.5 mtr long bend to shape including pole clamps made out of 40x5mm iron strip and nut bolts and washers complete all as specified and directed. 80 S&F LED street light fitting 50 watt 230V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. 81 M&L in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sq mm for phase and neutral and one run of 10.0 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the medium grade ISI mark PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and directed. Note : Wiring shall be done in proper colour coding. 82 M&Ldistribution board sheet steel powder coated for MCB with rated bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed.Note:- Distribution board and MCBs should be same make. 83 S &F in replacementof SPN 40 Amp rating 240V, 10KA C curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 84 S&F in replacement 240V, 10 KA C curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 85 S&F sheet metal enclosures, VPTN distribution board 4 way 415 V, double door with 100A MCCB as incomer complete with rated bus bar and neutral link earthing fixed flush in wall including chases wall for fixing DB and making good disturbed wall surfaces to match the existing specification complete all as specified and directed.Note:Distribution board and MCBs should be same make. 86 Earthing complete with galvanised iron earth plate electrode of size 600mm x 600mm x 6mm thick buried directly under ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level ,connected to galvanised earth lead wire 4.0mmby means of bolts, nuts, check nuts, washer including test point by means of bolts, nuts, check nuts, and washers of galvanized iron and connected to main switch / control board up to 7.5 metre away from earth electrodeand including GI pipe light grade 40mm bore protection pipe & necessary excavation and earth work in any strata, PCC chambers in PCC 1:3:6 type B1, RCC 1:2:4 type B1 cover slab 50mm thickwith 8mm dia TMT bars at 140mm C/C both ways,with lifting handle, watering pipe of GI medium grade 40mm dia, wire mesh, funnel, lugs and charcoal, salt etc all as applicable and as per plate No 3 of SSR Part-I and all as specified. 87 S&F 300mm sweep exhaust fan made out of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM1200, copper winding, 5 star rated complete all as specified and directed.Note:Old unserviceable exhaust fan to be deposited in MES store yard. 88 S&F 1200mm sweep ceiling fans complete with blade, down rods, electronic regulator and accessories, 230V min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed.Note:Old unserviceable ceiling fan to be deposited in MES store yard. 89 Taking down old unserviceable electric water geyser, S&F new electric storage heater (vertical type geysers) 25 ltrs BEE rating 5 Star, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet/outlet water connection in geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, thermostat cut off etc. complete all as specified and directed.Note: Old unsv electric water heater to be deposited in MES store yard. 90 S&F in repair electonic meter temper proof LCD display with polycarbonate cover three phase 415V, 10-60A accuracy class-1 50 Hz, conforming to IS 13779, IP-54, wth parameters to show data, time current reading, load, PF, voltage & KWH complete all as specified and directed.Note: old unsv energy meter to be deposited in MES store yard. 91 Supplying laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volta grade with stranded aluminium conductor of size 25 Sqmm , 3.5 core flatcable complete all as specified. 92 Excavation in trenches n exc 1.5 m wideand n exc 1.5 mtr in depth for foundation laying of under ground cable erecting of pole stay not exc 10 sqm on plain and not exc 1.5 m depth and getting out in any type of soil complete all as specified and directed. 93 Returning, filling in (soil ) including spreading, levelling, watering and well ramming in layers not exc 25cm in any type of soil complete all as specified and directed. 94 Removal ofexcavated material (soil) to a distance n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed. 95 M&L for sand cushioning to under ground cable with a layer of sand 8cm before laying the cable and 15cm after laying the cable (10cm punned thickness above the top of the upper most cable, total 18 cm), complete all as specified and directed. 96 M&L for sub class ‘B’ brick old size protection cover laid dry flat transversally along the length of cable on cushioning with width equal to the length of brick complete all as specified and directed. 97 Material and labour for GI tubing (light grade) with all fitting laid in trenches or along pole/bldg or under road crossing and protection pipe or fixed alongwith wall/pole with necessary clamp nut bolt and washer bore of pipe 40mm complete all as specified and directed. 98 M&L single phase 230V 50/60 Hz AC, aluminium painted boom barrier with IP 55 protection, automated operation using up/down bottn and remote, suitable boom length, height of boom from ground: 850 to 950mm, boom dimension: 60x40mm, operating climate: -5to 55 degrees, manual operation in case of power failure, do not bounce/jerk at the end positions, bar has protective rubber profile to prevent injury in caes of any contact, also has safety device to detect presence of vehicles and reversal of boom movement along with loop detector, complete in all respect all as specified and directed.
