|
| 1 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 2 | Of area 3 sq. metres and below |
| 3 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 4 | Of sectional area 40 square centimetres and above |
| 5 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 6 | Of area 3 sq. metres and below |
| 7 | Removing of window/vent grills for repair of window/vent frame/shutter and refixing the same grills after repair work with required screws, all complete |
| 8 | Taking out old grills from the dismantled windows/ventilation and joining by welding & modifying it to the required size and shape to fix it to the wall surface in the window / ventilation portion including providing additional sections embedding it in the wall with additional sections (with rich cement mortar) as required, all complete. (additional sections provided will be measured in item at Sl. no. 6.1) |
| 9 | For three shutter window |
| 10 | For two shutter window |
| 11 | For single shutter window/bathroom ventilation |
| 12 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 13 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 14 | Providing and fixing of WPC frame for doors with section of size 100x 65mm with density not less than 600kg/cum of approved quality, make and colour as per the requirement with required screws/fasteners, etc. all complete. |
| 15 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 16 | Sal wood/Bilanga/Padauk wood (Note: Work includes repair/lapping of existing frames. For measurement of frames, final finished section will be measured) |
| 17 | Providing and fixing of GI holdfasts of 5\" length and fixing it to the door/window/vent frame with required screws/nails, including cutting walls/concrete to 15cm x 15cm x 10cm and providing and laying 1:2:4 (1 cement: 2 pulverised sand: 4 aggregate 12.5mm nominalsize) mix cement sand concrete, all complete |
| 18 | Supply & fixing of WPC door shutter of approved quality, design & colour having thickness not less than 30mm, density not less than 500kg/cum, polished/printed/ laminated on one side and plain on other side including cutting to required size and fixing to existing wooden door frames. |
| 19 | Supply of powder coated Aluminium openable type window of approved section, size, thickness, quality, colour, etc. with 5mm thick frosted glass with EPDM rubber beading including providing sliding type fibre glass mesh assembly with aluminium framework to prevent entry of mosquito with required handles and locking arrangement, etc. all complete as per the direction of Engineer-in-charge/Incharge Estate Section. |
| 20 | Suppying of powder coated Aluminium ventilation of size (0.50x0.80m) with one intermediate partition and including 5mm thick fixed frosted glass in the lower half portion and 5mm thick frosted glass louvers in the upper half portion, with approved section all complete. (with 63.5x38.10mm section having thickness not less than 1mm) |
| 21 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) |
| 22 | Kiln seasoned selected planks of sheesham wood/Neem/Black Chucklam/pyima/tungping. |
| 23 | 30 mm thick shutters (window/vent shutters) |
| 24 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : |
| 25 | Float glass panes |
| 26 | 4 mm thick glass pane (weight not less than 10kg/sqm). |
| 27 | Providing and fixing 12 mm thick panelling or panelling and glazing inpanelled or panelled and glazed shutters for doors, windows andclerestory windows (area of opening for panel inserts excluding portioninside grooves or rebates to be measured). Panelling for panelled orpanelled and glazed shutters 25 mm to 40 mm thick. The work includes cutting out the damaged panel from the existing door shutter and fixing new panel with required beading, all complete. |
| 28 | Marine plywood conforming to IS: 710 |
| 29 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 30 | Providing and fixing of cupboard shutter made of 19mm thick water proof kitply plywood having lifespan of not less than 10 years by cutting to required size. The shutter should be of single piece and fixed to the existing framework with nickel plated bright finished MS piano hinges. |
| 31 | Removing old/damaged mesh of window/door shutters and providing and fixing of plastic/nylon mesh in window/door shutters including providing wooden beading wherever required all complete |
| 32 | Refixing of dismanlted door/window/ventilation shutters after repair work door/window/ventilation frames including minor adjustment to size of shutter by plaining of sides of shutter/adding beading to shutter to match the size of frame as required all complete. |
| 33 | Door shutter |
| 34 | Window/ventilation shutter |
| 35 | Supplying and fixing new wooden fillets wherever necessary: 14.8.2Hollock/Neem/Black Chucklam/pyima/tungping wood fillets |
| 36 | Providing and fixing of 26 gauge thick aluminium sheet over the steel main door shutter with required screws/rivet, etc. at required intervals, including applying a coat of metal primer on both sides all complete. |
| 37 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge. |
| 38 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC \"C\" channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the \"C\" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer\"s specification & drawing.9.120.130 mm thick plain PVC door shutters |
| 39 | Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : |
| 40 | 100x58x1.90 mm |
| 41 | 75x47x1.70 mm |
| 42 | Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 43 | 125 mm |
| 44 | 100 mm |
| 45 | 75 mm |
| 46 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 47 | Twin rubber stopper |
| 48 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 49 | 200x10 mm |
| 50 | 150x10 mm |
| 51 | 100x10 mm |
| 52 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screwsetc. complete : |
| 53 | 300x16 mm |
| 54 | Providing and fixing of SS eye hook of 150mm nominal size with required screws, etc. all complete |
| 55 | Plaining ofdoor and window shuters which are not closing/opening properly including making good the holes for tower bolts in frames for proper locking of doors and windows all complete. |
| 56 | Chipping out the damaged portion of kitchen slab, wall, cupboard slab, etc. and cleaning the surface and reinforcement wherever applicable and making it free from any loose particles, rust and ready for applying mortar. Providing and laying cement sand mortar in two or three layers including finishing the surface with 1:1 cement sand plaster for a total depth of 50mm average thickness all complete |
| 57 | Dismantling old damaged plumbing fittings and installations and providing and fixing the following new plumbing fittings and installations of approved make and quality, all complete |
| 58 | 100mm CP brass Shower with arm |
| 59 | 10L flushing cistern |
| 60 | EWC seat cover |
| 61 | CP brass bib cock |
| 62 | CP brass angular cock |
| 63 | Connector pipe PVC 2\" with brass unions |
| 64 | Providing and fixing of exhaust fan of approved make and quality with metal body and size 225mm and providing electric connection as required. |
| 65 | Applying priming coat: |
| 66 | With ready mixed pink or Grey primer of approved brandand manufacture on wood work (hard and soft wood) |
| 67 | Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :13.61.1 Two or more coats on new work |
| 68 | Dismantling old plaster or skirting raking out joints and cleaning thesurface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (Note: Exterior wall of two storey high building; rate is to be quoted including scaffolding charges for two storey building) |
| 69 | Providing and laying of PCC of 1:3:6 mix concrete at sill level of kitchen window including the cost of shuttering all complete as per the direction of Engineer-in-charge. |
| 70 | 12 mm cement plaster of mix : |
| 71 | 1:4 (1 cement: 4 fine sand) (Note: Exterior wall of two storey high building; rate is to be quoted including scaffolding charges for two storey building) |
| 72 | 1:6 (1 cement: 6 fine sand) (lintel portion, sill portion and jambs of dismantled window/door/ventilation in an average with of 20cm) |
| 73 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 74 | Providing and applying damp proof waterproofing material of approved quality and make such as Asian Paints Damp Sheath/ Dr. Fixit Roofseal/Dr. Fixit raincoat or equivalent in two coats as per the manufacturer\"s specification on the exterior wall surface. (Note: The rate is inclusive of scaffolding work for 2 storey building) |
| 75 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 76 | Shifting of dismantled materials such as door/window/ ventilation frames/shutters as per item at Sl. No. 1, 2, 3 from residential area to Estate section store upto a lead of 1 km, and stacking at site all complete as per the direction of Incharge Estate Section. |
