Tender For Provision Of Lighting Arrangement At Various Locations In Pochanpur Village In Ward No.120 Under Najafgarh Zone.Eee/Ngz/2025-26/04-02
Tender Value
25.87 Lakhs
Estimated cost
Bid Submission
09 Jun 2025
0 days left
EMD
54500
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
najafgarh → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Provision Of Lighting Arrangement At Various Locations In Pochanpur Village In Ward No.120 Under Najafgarh Zone.Eee/Ngz/2025-26/04-02
BOQ
| Sl. No. | Item Description |
| 1 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 2 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 3 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 4 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. mm |
| 5 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required Upto 35 sq. mm |
| 6 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 7 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 1.5 sq. mm |
| 8 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 9 | Supply of XLPE insulated PVC sheathed Al. Conductor Armoured Cable 1.1KV grade conforming to IS-7098 of following size:-4C*25 sqmm |
| 10 | Supply of XLPE insulated PVC sheathed Al. Conductor Armoured Cable 1.1KV grade conforming to IS-7098 of following size:-2C*10 sqmm |
| 11 | Providing and laying of HDPE PIPE OF 40mm outer dia with PN 4 rating by hand Moling/Mannual method Confirming to IS 4984 592 |
| 12 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp |
| 13 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.100 A,16KA,TPMCCB |
| 14 | Fabrication, supply & erection of 5.0 mtr height, 3 mm thick, bottom dia of 130mm & top dia of 70mm base plate of size 225 x 225 x 12 mm thick flange mounted hot dip galvanized octagonal pole made from HT steel plate,window with flash cover with full vertical window cover at appropriate height from the base plate on existing cement concrete pedestal as required. i/c supplying and fixing of 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. GI strips 4 mm thick of suitable length and having suitable size tapped holes as reqd, terminal block suitable for 25 sq mm conductor - 4 nos. & shorting links on DIN channel i/cpdg and fixing DIN channel of suitable length,, 6 Amp. SPMCB & C characteristics, earth stud, cable support clamp suitable for upto 4x25 sqmm cable. Logo/Name of manufacturer shall be embossed on the pole. Galvanization as per relevant IS code etc.as required. |
| 15 | Providing and laying in position M25 grade reinforced cement concrete foundation of size 450 mm (L) X450 mm (W) and 1000 mm deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia- 960 mm long(approx)-8 nos. and reinforcement of cold twisted bars of 8 mm dia- 1400 mm (approx) -6 nos.(with 150 mm spacing) as required with supplying and positioning of 4 nos. foundation bolts16 mm dia,600 mm long, J type i/c 2 nos. template anchor plates of size 225mm X 225 mm X 3mm and providing DWC HDPE for cable entry and exit as required for 3 m and 5 mtr pole. |
| 16 | Fabrication, supplying and fixing class B Galvanised single overhang arm bracket made out of 250 mm long galvanized top tube with cap & 250 mm long 32 mm dia galvanized pipe with tightening bolts complete as reqd. |
| 17 | Supply of 20 Mtr.high mastsystem with its accessories (as per IS:875 part-1-2015/BSEN10025 and IS:2062), Mast shall be in two section, hot dip galvanizedinside and outsides as per IS 4759/BSEN 1461 and suitable for wind velocity as per IS 875 (part-3) 1987. lantern carriage suitable for up to 6 nos asymmetrical loaded luminaries with welded arm (excluding luminaries), mast head frame assembly with full cover, suitable for1 No. LED aviation obstruction lights, double drum type self sustaining winch, integral power tool accessible from door with padlocking arrangement (winch motor with control circuit) hot dipped galvanized heavy duty pipe lightening finial, Stainless steel 6 mm dia. wire ropes (AISI 316, 7 / 19 construction 2 no. rope for lantern carrage & 2 no. rope for winch assembly ), torque limiter, reverse / forward motor operation. The mast cut and folded to form a polygonal section, telescopic jointed and welding as per BS 5135.etc with12 nos. foundation bolt, M30*850 mm long, i/c 2 nos. Anchor plate of size 670mm dia, 3 mm thick as required. 20 Mtr height, bottom thickness 4 mm & top thickness 3 mm, bottom dia. 460 mm & top dia. 150 mm with base plate dia. 670 mm & 30 mm thick. Logo/Name of manufacturer shall be embossed on the pole. |
| 18 | Design and casting ofshallow foundation with M20 grade concrete for erection of20 Mtr highmast considering the safe soil bearing capacity at site as 10T/sqmtr in any type of soil area includingplacing foundation bolts. Straitening , cutting, bending and placing in position reinforcement base, column & rings strictly as per bar bending schedule and drawing complete as required by Engineer-in-charge with all material and labour etc. as reqd. |
| 19 | Erection of 20 Mtr high mast with the help of suitable tools and plant, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitablecopper conductor cores of 2.5 sqmm, connections, joints, lugs, MCB, isolator and labour etc as required. |
| 20 | S/I/T/Cof350W LED Sports Flood Light Luminaire fitted with lens, made of pressure dia. cast aluminium housing & toughened glass cover complete. Lens Beam Angle of 25 degree with system Beam angle not exceeding 30 degree with following specifications as reqd. with IP 66 protection (a) Total system wattage= 350W +/- 5 % (b) Luminaire Efficiency >=120 Lm/w (c) Power Factor >= 0.95 (d) Protection Class- IP- 66. |
| 21 | S/I/T/C of 12W LED single dome aviation obstruction light made of die-cast aluminum alloy housing with polycarbonate with following specification (a) Protection class-65 (b) Color- Red. |
| 22 | Fabrication, Supplying, Installation, testing, Commissioning of 12 metres high mast System with its accessories ,Mast shaft shall be in one section , hot dip galvanized 4mm thick (Single dip ) inside and out sides and suitable for wind velocity as per IS 875 part3 .There shall be in longitudinal seam weld per section and No circufrential weld. It should also included accessories for High Mast head frame ,2 point suspension system, 5x2.5 sqmm copper conductor with steel wire rope 5mm dia. (7/19construction) single drum winch ,galvanized lantern carriage arrangement suitable for 4/6 Nos. flood light luminaries luminaries symmitrically and its control gears boxes and lighting finial ,the mast shall have integral type manual tool mounted at the base compartment of its raising and lowering operation with foundation bolts and Anchor plate and control panel housing suitable RCC (1:2:4) shallow foundation of size 1m(L)X1m wide and 2m deep i/c excavation of earth, providing cutting, bending and placing in position, rewinforcement of cold twisted bars of 12 mm dia -2100 mm long (approx.) - 16 nos.and reinforcement of cold twisted bar of 8 mm dia - 3700 mm (approx.) - 13 nos. (with 150 mm spacing) as required withpositioning of foundation bolts and providing DWC HDPE pipe for cable entry & exit as required for the semi high mast considering the safe soil bearing capacity at site as 10T/sqm at 2mts. Depth with all material i/c,4Nos S.PMCB, 1 No. double pole 16 amp. MCB etc as reqd. Logo/Name of manufacturer shall be either embossed or rivited plate on the pole. Galvanized as per relevant IS. |
| 23 | Supply and fabrication of pole protection system made up of 8SWG steel wire mesh of size 25mmx75mm rectangular with 50mmx50mmx6mm MS angle iron for supporting the mesh i/c MV danger plate and grounding the protection system in suitable quality of CC etc as reqd. |
| 24 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a) 40 A |
| 25 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA,amp C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(a) Single Pole |
| 26 | Providing and fixing name board made of MS sheet 90*60 cm,1mm thick with frame of MS angle 50*50*6mm, two diagonal braces at bthe back of the sheet of MS flat 40*6mm ,total height of the board above ground level 2.40m, length of legs below ground 0.30m embedded in CC block 1:2:4(1 cement:coarse sand:4 graded stoneaggegate 20mm nominal size) 30*30*45 cm including excavation and removal of surplus earth with in 50m lead, applying priming coat of approved steel primer,painting with syntheic enamel paint of approved quality and lettering with enamel paint of approved colour (one side) as per drawing/direction of Engineer-in -charge. |
| 27 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level, 1:3:6 (1 Cement: 3 coarse sand (zone-III) drived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources. |
| 28 | Supply of 45 watt LED Street Light Luminaire fitted with lens made of pressure die cast aluminum housing and toughened glass cover complete with the following specifications as per relevant IS(a) Total System Wattage : 45 Watt + 5%(b) Luminaire Efficacy -120 Lumens/watt ( minimum)(c) Powerfactor > 0.95(d) Protection Class IP66(e) LED Package shall be Ceramic Base(f) Multi chip, Array, Multi Die, Mid power, Integrated Arrays and COB type LED Chip is not permitted.(g) Operating Current of LED < 70% of rated maximum forward current, limited to a minimum of 350 mA and maximum of 1000 mA.(h) Wattage of LED Package : One watt to Five watt maximum(i) CRI >70(j) THD<10% for complete fixture(k) Operating Voltage – 110-320 V, 50Hz +/- 3%.(l) The driver must have thermal Protection against 75 deg C ambient temperature with internal SPD of minimum 6 KV. Separate Compartment for Driver(m) Life of Street Light: Minimum 50,000 hrs |
| 29 | Supply of 70 watt LED Street Light Luminaire fitted with lens made of pressure die cast aluminum housing and toughened glass cover complete with the following specifications as per relevant IS(a) Total System Wattage :70 Watt + 5%(b) Luminaire Efficacy -130 Lumens/watt ( minimum)(c) Powerfactor > 0.95(d) Protection Class IP66(e) LED Package shall be Ceramic Base.(f) Multi chip, Array, Multi die, mid power, integrated arrays and COB type LED Chip are not permitted.(g) Operating Current of LED < 70% of rated maximum forward current, limited to a minimum of 350 mA and maximum of 1000 mA.(h) Wattage of LED Package : One watt to Five watt maximum(i) CRI >70(j) THD<10% for complete fixture(k) Operating Voltage – 110-320 V, 50Hz +/- 3%.(l) The driver must have thermal Protection against 75 deg C ambient temperature with internal SPD of minimum 6 KV. Separate Compartment for Driver(m) Life of Street Light: Minimum 50,000 hrs |
| 30 | Supply of140 watt LED Street Light/Flood Light Luminaire fitted with lens made of pressure die cast aluminum housing and toughened glass cover complete with the following specifications as per relevant IS(a) Total System Wattage :140 Watt + 5%(b) Luminaire Efficacy -130 Lumens/watt ( minimum)(c) Powerfactor > 0.95(d) Protection Class IP66(e) LED Package shall be Ceramic Base(f) Multi chip, Array, Multi Die, Mid power, Integrated Arrays and COB type LED Chip is not permitted.(g) Operating Current of LED < 70% of rated maximum forward current, limited to a minimum of 350 mA and maximum of 1000 mA.(h) Wattage of LED Package : One watt to Five watt maximum(i) CRI >70(j) THD<10% for complete fixture(k) Operating Voltage – 110-320 V, 50Hz +/- 3%.(l) The driver must have thermal Protection against 75 deg C ambient temperature with internal SPD of minimum 6 KV. Separate Compartment for Driver(m) Life of Street Light: Minimum 50,000 hrs |
| 31 | Supply and fixing of 32mm dia X 1 meter long G.I. Pipe (Medium Class) bracket for mounting of fluorescent/HPMV/HPSV Street Light fitting on pole including bending the pipe to the required shape , 2 nos 25mm X 6mm flat iron clamps with nuts, bolts and washer , painting the flat iron with primer and finish paint etc. as reqd. |
| 32 | Installation and Commissioning of Street Light/Flood light etc. as required. |
AI Tender Summary
Tender Timeline
May 29, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedJun 09, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 09, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender