Construction of sub Division Office Building at SANKAD= 1 Earth work in excavation by mechanical means (Hydraulic Excavator)/Manual means in foundation trenches or drains (not exceeding 1.50 m in width or 10 Sqm on plan) including dressing of sides and ramming of bottoms,lift upto 1.5 mtrs including taking out the excavated soil and depositing and refilling of jhiri with waterng and ramming and disposal of surplus excavated soil as directed within a lead of 50 mtrs. All kinds of soils. (B-44/1.8) 2 Providing & laying in position cement concrete including curing, compaction etc .complete in specified grade excluding the cost of centering & shuttering.All work upto plinth level 1:4:8. (B-54/3.1.6) 3 Randam Rubble stone masonary for with hard stone in foundation & plinth in cement sand mortar 1:6 for above 30 cm thick walls. (B-69/6.1.6) 4 Randam Rubble stone masonary with hard stone in super structure above plinth level & upto five level for walls upto 30cm or less in thicknessin cement sand mortar 1:6 (B-69/6.2.6+6.3.4) 5 Add exra for facing as per design & detailled specification including additional cost of stone for Course Rubble Facing First Sort.(B-70/6.4.1) 6 Add exra for facing as per design & detailled specification including additional cost of stone for Course Rubble Facing Second Sort.(B-70/6.4.2) 7 Add extra for rock facing using Jodhpur white sand stone with proper projection and chisal dressing of edges of stone 2 line dressing for building corners, jambs including uniform joints. (B-70/6.4.6) 8 Add extra for randan rubble stone masonary with hard stone in square or rectangular pillars. (B-69/6.3.1) 9 Providing & laying in position specified grade of cement concrete for all RCC structural elements up to plinth level including curing, compaction, finishing with rendering in CM 1:3 & making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering & reinforcement. M-20 Grade. Nominal/Design Mix. (B-59/4.1) 10 Providing & laying in position specified grade of cement concrete for RCC structural elements up to five level including curing, compaction, finishing with rendering in CM 1:3 & making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering & reinforcement for Beams, suspended floors,roofs, landings, balconies, shelves, chhajjas, lintels, staircases etc. M-20 Grade. Nominal/Design Mix. (B-59/4.3) 11 Centering & Shuttering with plywood or steel sheets including strutting, propping, bracing bothways & removal of formwork for Foundation, footings, srap beams, rafts, bases of columns etc.(B-61/4.9) 12 Centering & Shuttering with plywood or steel sheets including strutting, propping, bracing bothways with steel props & removal of formwork up to floor five level for suspeded floors, roofs, landings, balconis, girders, cantilevers, sills, chhajjas, lintels, beams, plinth beams etc.(B-61/4.10.2) 13 Providing & Fabricating steel reinforcement for RCC work including straightening, cutting, bending, placing in position &binding (incl. cost of binding wire).All complete upto floor five level. Cold twisted deformed bars. (IS:1786). (B-62/4.13.1) 14 P & L in cement concrete including curing,compaction etc. complete in retaining walls, return walls, walls including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, fillets, levelling course etc upto floor five level excluding the cost of C& S. M-10 Grade Nominal Mix 1:3:6.(B-55/3.2.4) 15 Half brick masonary in super structure above plinth level upto floor V level using bricks of designation 75 with providing & placing 2 Nos. 6mm MS bars at every third course in CM 1:6. (B-66/5.8.3+5.9) 16 Supplyng & Fixing in walls machine cut & polished stone shelves, tands & sills in CM 1:3 with machine cut edges. Kota stone minimum 30 mm thick.(B-72/6.17.3) 17 Providing & Fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joints mitred, welded & grinded including hold fast of steel lugs 13x3mm, 15 cm. long embedded in CC blocks 15x10x10 Cm. of 1:3:6 nominal concrete & including fixing of pivoted hinges of superior quality, Window shutters made out of 50x25 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred & grinded including 10x10 mm Square bars welded to frame for paitam fixing float glass 4 mm thick panes with glazing clips & metal sash putty & fixing of shutters frame peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing & jointing with frame hinges priming coat with steel primer complte in all respect as per direction of Engineer-in-charge. Window openable. (B-102/9.28.1). 18 Providing & Fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joints mitred, welded & grinded including hold fast of steel lugs 13x3mm, 15 cm. long embedded in CC blocks 15x10x10 Cm. of 1:3:6 nominal concrete & including fixing of pivoted hinges of superior quality, Window shutters made out of 50x25 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred & grinded including 10x10 mm Square bars welded to frame for paitam fixing float glass 4 mm thick panes with glazing clips & metal sash putty & fixing of shutters frame peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing & jointing with frame hinges priming coat with steel primer complte in all respect as per direction of Engineer-in-charge. Window fixed. (B-102/9.28.2). 19 Supplying & Fixing of fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3 mm with suitable screw at not exceeding 150 mm distance.(B-102/9.26) 20 P & F square bars or other flates welded to window, ventilators etc.(B-102/9.27) 21 Pointing on stone masonary in CM 1:3. Deep groove pointing.(B-143/12.31.3) 22 Plaster on new surface on walls in CM 1:6 including racking of joints etc. complete fine finished. 25 mm thick. (B-139/12.3.1) 23 Plaster on new surface on walls in CM 1:6 including racking of joints etc. complete fine finished. 20 mm thick.(B-139/12.3.2) 24 Plaster on new surface on walls in CM 1:4 including racking of joints etc. complete fine finished. 25 mm thick.(B-139/12.2.1) 25 6mm thick cement plaster to ceiling of mix 1:3.(B-139/12.5) 26 P & L broken glazed tiles on roof (broken glazed tiles not less than 9 Kg/Sqm) on top of hot bitumen @1.70 Kg/Sqm. (1.40 Kg of VG-40 (30/40) grade & 0.30 Kg/Sqm of VG-10 (80/100) grade) joints filled with CM 1:2 (1Cement:2 Marble dust mixed with water proofing compound) all complete as per directions of Engineer-in-charge. (B-109/10.24) 27 P & F machine cut fine dressed red/pink sand stone dasa or coping, with fuul moulding if required laid on CM 1:4 including pointing with admixture of pigment matching with the stone shade. 75 mm thick. (B-72/6.19.3) 28 P & F pressed steel door frames confirming to IS:4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead & if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.25 mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel strike-plate & shock absorber as specified & applying a coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4 (M-15 Grade) complete as directed by Engineer-in-charge. Profile- B. (B-99/9.6.1) 29 Providing & Laying of Coloured Paver blocks as per IS:15658:2006 (Indian standard for precast concrete block for paving specifications) & IRC: SP63-2004 (Guidelines for the use of interlocking concrete block pavements). M-40, 80 mm thick to be used in medium traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight or an equivalent of 0.50 to 2.0 MSA for a design life of 20 years) like City streets, small & medium market roads, low volume roads, utility cuts on arterial roads etc. Category-C not denated on any of its faces like Hexagonal, rectangular, square shape as per IRC: SP63-2004. (B-135,136/11.38.2(C)+B-137/11.40) 30 P & F external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal,dehydreresin in glue both sides with approved steel fittings complete as per Annexure-A. 30 mm thick. Commercial Veneer both side. (B-105/8.18.2) 31 P & F 1st quality Vitrif ied Porcelain Polished Tiles on floor, skirting & steps etc. in different sizes (thiskness to be specified by the manufacturer) with water absorption less than 0.08% & confirming to IS:15622 of approved make in all colour & shade, laid with 20 mm thick CM 1:4 including grouting the joints with white cement & matching pigment ect complete of size 600x600 mm. (B-87/7.18.2) 32 Kota stone slabs 25 mm thick in risers of steps, skirting, dado & pillars laid on 12mm(Av.) thick CM 1:3 & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete for area of each slab from 2001 to 5000 Sq.cm. (B-132/11.19.2) 33 Kota stone slab flooring 25 mm thick over 20 mm (Av.) thick baselaid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of CM 1:4. For area of each slab from 2001 to 5000 Sq.cm. (B-132/11.18.2) 34 Kota stone slab flooring 25 mm thick over 20 mm (Av.) thick baselaid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of CM 1:4. For area of each slab from 901 to 2000 Sq.cm. (B-132/11.18.1) 35 P & F 1st quality standard white, grey, ivory, fume red brown, light green, light blue & other light shades Glaged Tiles confirming to IS: 13753 & IS: 15622 of size 300x200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of the time complete (excluding the cost of cement plaster on walls & pillar). (B-86/7.12). 36 P and F 1st quality MAT finished ceremic tiles size 300mm x 300mm confirming to IS:13755 & IS: 15622 colour such as white, grey, ivory, fume red brown, light green, light blue & other light shades infloors, steps, pillars etc laid on a bed of neat cement slurryfinished with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortar bed). (B-86/7.13) 37 P & F Granite stone slab mirror polished & machine edge cut in walls, pillars, steps, shelves,sills, counters, floors etc. laidon 12 mm (Av.) thick base of CM 1:3 jointing with white cement mortar 1:2 with pigment to match the shade of the marble slab complete including grinding, rubbing & polishing of Jhunjhunu/Jalore (Red/Chocolate Colour) of size above 3600 Sq.cm. (B-84/7.5.1(iii)) 38 P&FMS sheet 1.0 mm thick double leaf door shutter in angle iron frame of 35x35x5 mm suitably diagonally braced with 25x3 mm flat iron above & below lock rail of size 50x5 mm beading extra including all fittings as per direction of Engineer Incharge but excluding the cost of Choukhats including two coats of anti corrosive red oxide paint. (B-100/9.17+B-101/9.17.1) 39 P & F of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25x1.25 mm thickwith 1 mm MS sheet to spot welded including holdfast of 15x3 mm, MS oxidised fittings such as butt hinges, sliding doors bolts, handles, tower bolts & twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate & spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge. (B-104/9.39) 40 Stone slab roofing on groung floor with fine grained stone slab from approved quarry including filling of joints parapet & slab on both sides in cement sand mortar 1:4 with ceiling pointing in cement sand mortar 1:3 complete as per specification & instruction of Engineer In Charge. (B-107/10.16) 41 Providing Gola 75x75 mm in cement concrete (1:2:4) including finishing with CM 1:3 as per standard design. (B-109/10.22) 42 Cement Concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry, making of lines or grooves etc. completebut excluding the cost of nosing of steps etc. complete. 75 mm thick with 20 mm thick nominal size aggregate. (B-128/11.3.2) 43 Finishing with neat cement (Punning). (B-140/12.7) 44 Providing & Fixing wood panelling or panelling & glazing in panelled or panelled & glazed shutters for doors, windows & clearstorey windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled & glazed shutter 25 to 40 mm thick. Ghana wood Grade-I, Wire gauge 24 gauge 14 mesh of IS designation 85 gauge wires of dia. 0.56 mm panels. (B-91, 92/8.6.8) 45 P & F in position Collapsible steel shutter with vertical MS channel 20x10x2 mm & brackets with flat iron diagonals, 20x5 mm size with top & bottom rail of T-iron 40x40x6 mm with 40 mm dia steel pulleys/ball bearing complete with bolts, nuts locking arrangements inside & outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured & paid as per outer dimensions). (B-99/9.10) 46 S & F in Cement Mortar welded hand railing made out of MS round or square bars,flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. (B-9/9.7) 47 Providing & Fixing steel gate grating & grills made of angles, tees, square bars or other flats, black pipe with holdfast & fittings complete as per design & drawing including cutting, welding & fabrication withpriming coat of red oxide. (B-99/9.8) 48 Structural steel work riveted, bolted or welded in built up sections, trusses & framed work including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer all complete. (B-98/9.2) 49 Add extra for providing & fixing Wind ties of 40x6 mm flat Iron section. (B-106/10.11) 50 Providing Non-Asbestos high impact Polypropylene reinforced Cement 6 mm thick corrugated sheets (as per IS:14871) roofing upto any pitch & fixing with polymer coatedJ or L - hooks, bolts & nuts 8 mm dia. GI plain & bitumen washers or with self drilling fasteners & EPDM washers etc. complete excluding the cost of purlins, rafters & trusses corrugated sheets & including cutting to size & shape wherever required. (B-106/10.8) 51 Providing & laying in position cement concrete including curing,compaction etc .complete in specified grade excluding the cost of centering & shuttering.All work upto plinth level 1:2:4.(B-54/3.1.2) 52 Supply & filling in plinth with blown sand under floors including watering, ramming, consolidating & dressing complete including cost of sand. (B-48/1.27(b)) 53 P & F 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade-I, IS:3087 marked including top cover of 6 mm commercial ply wood confirming to IS:303 BWR grade, nickel plate MS 20 mm dia. curtain rod with nickel plated bracket including fixing with 25x3 mm MS flat 10 cm long all complete. (B-95/8.24) 54 Making grooves as per design in plaster 10 to 20 mm wide.(B-141/12.19) 55 S & F Soorsagar Bhura or Equivalent ashlar sills, lintels & dassa, bearing bed & top surface made perfectly even, jambs, skirting, steps etc. rough dressed up to 15 cm thick. (B-74/6.27.1) 56 Providing & fixing anodizing aluminium work for doors, windows, ventilators and partition with extruted built up standard tubular/appropriate Z sections & other sections of approved make confirming to IS : 733 and IS : 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium section shall be smooth rust free, straight, mitred and joined mechanically wherever required including cleat angle Aluminum sanp beading for glazing/ paneling, C.P. Brass / Stainless Steel screws, Aluminum. Tower bolt & aluminum handle & Aluminium Aldrop etc. all complete as per architectural drawing & the directions of Engineer-in-charge (Glazing and peneling to be paid for separately). For fixed portion. Anodised Aluminium (anodised transparent 81 dyed to required shade according to IS : 1868 (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer). (B-175/16.1.1.1) 57 Providing & fixing anodizing aluminium work for doors, windows, ventilators and partition with extruted built up standard tubular/appropriate Z sections & other sections of approved make confirming to IS : 733 and IS : 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gas at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium section shall be smooth rust free, straight, mitred and joined mechanically wherever required including cleat angle Aluminum sanp beading for glazing/ paneling, C.P. Brass / Stainless Steel screws, Aluminum. Tower bolt & aluminum handle & Aluminium Aldrop etc. all complete as per architectural drawing & the directions of Engineer-in-charge (Glazing and peneling to be paid for separately). For shutters built up standard tubular sections of openable doors, windows & ventilators including providing and fixing hinges/ rollers etc. and making provision for fixing of fittings wherever required. (Locks shall be paid for separately).Anodised Aluminium (anodised transparent 81 dyed to required shade according to IS : 1868 (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer). (B-175/16.1.2.1) 58 Providing & fixing glazing in aluminum door, window, vintilator shutters and partitions etc. with PVS/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminum snap beading shall be paid in basic item)with glass panes of 5.0 mm thickness (weight not less than 13.50 Kg. per sqm) as per IS : 2835 (B-176/16.5.2) 59 Providing & fixing expanded grill made of anodised aluminum as per desin and drawing having members section of size 7.5 mm X 6 mm and opening of size 102 X 99 mm to aluminum window/vent with required screws, Y and H aluminum section (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer-in-charge. Anodised Aluminium (anodised transparent 81 dyed to required shade according to IS : 1868 (Minimum anodic coating of grade AC 15, Anodizing to be got done from approved Anodizer). (B-177/16.10.1) 60 Providing & Fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked, for doors including cost of cutting floors as required embedding in floor and cover plate with Brass pivots & single piece MS with stainless steel cover plate. (B-176/16.6.1) 61 Providing & Fixing 100 mm Brass locks (best make of approved quality) for alluminium doors including necessary cutting & making good etc. complete. (B-177/16.8) 62 Providing and fixing IS:3564 marked Aluminium die cast body tubular type universal hydraulic door closure with necessary accessories & screws etc. complete.(B-955/8.26) 63 Providing & Applying Plaster of Paris putty of 2 mm thickness over plastered surface to prepare the surface even & smooth complete. (B-142/12.23) 64 Finishing wall with water proofing cement paint of approved brand & manufacture & or required shade to give an even shade including all scaffolding. New work (Two or more coats applied @ 3.84 Kg/10 Sqm). (B-145/12.41.1) 65 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding. New work (two or more coats) over and including scrapping and priming coat with cement primer. (B-144/12.37.1) 66 Painting with synthetic enamel paint of approved brand & manufacture to give an even shade.Two or more coats on New work.(B-146/12.46.1) 67 P & F Indian type White Glazed Vitreous China 1st quality W.C. Orissa Pan IS:2556 Mark) with 100 mm vitrous china P or S trap including cutting & making good the walls & floors of size 580x440 mm.(BS-217/1.2.2) 68 Providing & Fixing European type white glazed vitreous china 1st quality W.C. pan (IS:2556 mark) with P or S trap including cutting amd making good the wall and floor. (B-217/1.3) 69 Providing & Fixing water closet Seat Covers with brass hinges complete solid PVC (IS:2548 marked) grade-I white for EWC (B-218/1.7.2) 70 Providing & Fixing Low level flushing cistern of 10 liters capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall PVC with PVC bend & superior internal fittings as per IS : 7231 (B-219/1.20.3) 71 P & F WVC Wash Basin (1st quality, IS:2556 Mark) of approved make with C.I. brackets duly painted, 1No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall of size 510x400 mm.(B-221/1.36.2) 72 P & F Chlorinated Poly Vinyl Chloride (CPVC) pipes (IS:15778:2007 code) having thermal stability for hot & cold water supply including all CPVC plain & Brass threaded fittings including fixing the pipe with clamps at 1 meter spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement & the cost of cutting chases & making good the same including testing of joints complete as per directions of Engineer In Charge. (Concealed work including cutting chases & making good the walls etc.). 15 mm Nominal size. (BS-240/2.38.1) 73 P & F Chlorinated Poly Vinyl Chloride (CPVC) pipes (IS:15778:2007 code) having thermal stability for hot & cold water supply including all CPVC plain & Brass threaded fittings including fixing the pipe with clamps at 1 meter spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement & the cost of cutting chases & making good the same including testing of joints complete as per directions of Engineer In Charge. (Concealed work including cutting chases & making good the walls etc.). 25 mm Nominal size. (BS-240/2.38.3) 74 P & F Chlorinated Poly Vinyl Chloride (CPVC) pipes (IS:15778:2007 code) having thermal stability for hot & cold water supply including all CPVC plain & Brass threaded fittings, this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per directions of Engineer In Charge. (External work) . 15 mm Nominal size. (BS-240/2.39.1) 75 Making Connection of G.I. distribution branch with main including all fitting upto 25 mm dia. (B-231/2.3.1) 76 P & F Looking Mirrors with PVC frame of approved make as per directions of Engineer-In-Charge. of size 500x400 mm . (B-223/1.45.1) 77 P & F towel rail or ringof approved quality/make. C.P. brass towel rail with bracket600x20 mm.(B-223/1.47.4) 78 P & F towel rail or ringof approved quality/make. C.P. Brass towel ring revolving type (B-224/1.47.8) 79 Construction of Cement Concrete Chamber 125 mm dia. Stainless Steel sheet grating. (B-255/3.38.4) 80 P & F Bib Cock (IS:8931 Mark) Superior quality of approved make. Brass 400 gm. 15 mm nominal bore. (B-231/2.7.1) 81 P & F Bib Cock (IS:8931 Mark) Superior quality of approved make. C.P.Brass Bib cock 15 mm nominal bore.(B-231/2.7.3) 82 P & F Bib Cock (IS:8931 Mark) Superior quality of approved make. C.P.Brass Bib cock Long body 15 mm nominal bore weight not less than 690 gm. (B-231/2.7.4) 83 P & F Inlet Connection (Angle Valve) Superior quality of approved make for Wash Basin, Gyser etc. C.P. Inlet connection 15mmBrass (IS:8931 Marked).(B-233/2.12.1) 84 P & F Ball Cock (IS:1703 Mark) with Rod & PVC Ball complete : Brass wt. not less than 300 gm. 15 mm. (B-232/2.11.1) 85 P & F 15 mm dia. Connection pipe of approved quality/make. PVC pipe with C.P. Brass nuts up to length 450 mm. (B-233/2.13.3) 86 P & F Flush Cock/Flush Valve (IS:9758 Mark) for WC of approved make. Brass/ Gun metal Half-turn wt. 1 Kg. of approved quality/make, 25mm nominal bore. (B-233/2.14.9) 87 P & F Full-way (IS:778 Mark) or Wheel valve of approved make :Gun-metal15 mm nominal bore. (B-233/2.15.1) 88 P & F Full-way (IS:778 Mark) or Wheel valve of approved make :Gun-metal 25 mm nominal bore. (B-233/2.15.3) 89 P & F Jet spray for water closet with C.P. copper tube flange of approved make. (B-226/1.59) 90 P & F 1st quality WVC Urinal (IS:2556 Mark) with 25 mm dia. G.I. waste pipe, dome couplings, concealed iron brackets or screws etc. complete. Flat Back (small) size 456x355x265 mm. (B-218/1.14.1) 91 P & F Marble Urinal Partition slab both sides polished of approved desgn cut from marble size 900x600 mm. Makrana Adanga or Rajnagar 1st quality white or Andhi Indi-Italian marble. (B-219/1.16.3) 92 P & F PVC Storage Tank (IS:12701 Marked Indicating BIS license No.) of approved make with cover, 25 mm dia. 1 M long G.I. over flow pipe & 25 cm long wash out pipe with plug & socket, including making connection etc. complete of approved design. 500 litres capacity. (B-236/2.26.3). 93 P & F Square-mouth Gully Trap A grade (IS:651-1992 Marked) of approved makecomplete with C.I. grating, frame & Cover masonary chamber in CM 1:6, 100 mm thick C.C. 1:5:10 base concrete, 40 mm thick C.C. M-15 grade coping, 12 mm thick cement plaster in CM 1:3 complete as per approved design & type. Trap size 150x100 mm, ferrow cement coverwith frame, Internal Chamber size 300x300 mm.(B-244/3.5.1) 94 Construction of Manhole in all type of soils inner size 90x60 cm., 300 mm thick masonary in CM 1:6, 10 cm. thick C.C. 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6 finished with floating neat cement, 50 mm thick M-15 grade C.C. flooring, making channels, 80 mm thick stone slab covering with 40 mm thick M-15 grade C.C. flooring, Cement cover with frame of450 mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 Mtr. lead. Depth upto 0.50 Mtr. (B-250/3.19.1) 95 Construction of Soakage Well in all type of soils 300 mm thick dry masonary, top & bottom 300 mm course in CM 1:6, 80 mm thick stone slab, jointing of slab in CM 1:3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C. flooring, earthwork etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 Mtr. of size 240 cm dia. outside & 240 cm depth. (B-252/3.22.3) 96 Construction of septic tank in all type of soil with 40cm thick masonary in CM 1:6 15cm thick CC bed of 1:5:10, M-15 grade CC floor, 50mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos. stonefoot rests of approved design, two No. 450 mm dia. each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of earth within a lead of 50 mtr. size 230x110x150cm ( for 20 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 10 mm dia @15 cm C/C bothways including shuttering complete in all respect. (B-253/3.27.2) 97 Construction of Chamber in all type of soil with 300 mm thick masonary in CM 1:6 100mm thick C.C. 1:5:10 in foundation 20mm thick inside plaster in CM 1:6 finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, earth work etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. Inside size 300x300 mm depth up to 0.50. Cement cover with frame. (B-251/3.21.1) 98 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type-B for sciland waste discharge system (IS;13592:1992 Marked) of approved quality/ make. 75 mm(B-257/3.44.1) 99 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipes type-B for sciland waste discharge system (IS;13592:1992 Marked) of approved quality/ make. 110 mm(B-257/3.44.2) 100 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. 110 mm dia. Bend 87.5 Dg. (B-257/3.45.4(ii)) 101 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make.110 mm Dia. Single Tee with Door (B-258/3.45.17(ii)) 102 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. Coupler110 mm. (B-257/3.45.1) 103 P & F Unplasticized Poly Vinyl Chloride (UPVC) SWR pipe fittings type B for sciland waste discharge system (IS:13592:1992 Marked) of approved quality/make. Vent Cowel 100 mm. (B-259/3.45.30) 104 P & F Kitchen & Lab. Sink of approved make with CI brackets duly painted, 40 mm CP waste coupling, CP brass chain with rubber plug, 40 mm GI waste pipe up to floor level complete including cutting & making good the wall & floor. 1.0 mm thick Salem stainless steel AISI-304 & IS:13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling. With overall Size 24x18x8 & Bowl size 20x16x8 mm. (B-222/1.39.9.3) 105 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR Short point (up to 3 mtr.)(E-01/1.1.1). 106 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq mm ---do---- making connections, testing etc. as required. Medium point (Upto 6 Mtr.)(E01/1.1.2) 107 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq mm ---do---making connections, testing etc. as required. Long point (Upto 10 Mtr.) (E01/1.1.3) 108 Wiring of twin control light point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 2 Nos hot dipped Galvanized MS Modular box of 1.2 mm thickwith earth terminal, 2 Nos 10A two way Modular switch, 3 pin ceiling rose / Holder /3 way connector, Modular face plate with grid plate, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR Long point (up to 10 mtr.)(E-01/1.2.3). 109 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR. On board (E-02/1.3.1). 110 Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification ofWiring accessories refer ChapterE - 07related item & For additional technical parameters of product / work refer Annexure A attached with this BSR. (E-07/7.37) 111 P & F 1.2 mm thickG. I. / M .S. Sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required.For additional technical parameters of product / work refer Annexure A attached with this BSR. 250mm x 300mm x 75mm (E-05/13/5.1.1.11) 112 P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR. (E-05/15/5.9) 113 P & Fof IP-65 IK08, IP-66 rated integrated SMD mid power LED bulk head type light fixture made from pressure die cast AL housing suitable with integral driver, system lumen efficiency >100 Lm/Watt output, THD<10%, PF>0.95, CRI>80, life time of minimum 50000 burning hours with 70% of initial Lumen maintened till life ends, CCt 3000K/4000K/5700K/6000K/ 6500K (AS per ANSI Bin), maximum power consumption should not be more than the specified rating & fixture shall be of BIS standard & trade mark certificate (TC). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing, surge protection 4 KV. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate/Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of product/work, refer Annexure A attached with this BSR. Minimum Lumen output 1000 Lm. (E-17/17.6.1). 114 Providing & Fixing of Street light bracket made out from following size of B class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .32 mm (E-18/96/18.18.3) 115 Pipe Earthingas per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. B class G.I. Pipe IS: 1239 (Part-1) 2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . (E-14/73/14.1) 116 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. Single Pole MCB of 6 A to 32 A rating (E-06/17/6.1.1.2) 117 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. single Pole MCB of 40 A rating (E-06/17/6.1.1.3) 118 Providing & Fixing of 240/415 V Isolator ISI marked IS:13947-III / conforming to IEC 60947-3, suitable for AC22A utilization category, 4 KV impulse withstand voltage, true contact indication, red colour dolly/lever shall have single mould covering over all poles for operation, two position din rail mounting, minimum phase termination capacity of 35 Sqmm. IP 20 contact protection & fitted in existing distribution board/sheet including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. Double Pole Isolator of 63 A rating (E-06/18/6.2.1.2) 119 Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR. Glazed door (Single phase) 12-way (E-06/22/6.10.2.4) 120 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1170mm (+/-10%) LED batter with min. lumen output 2200 lm (E-17/87/17.1.1) 121 Providing & Fixing of energy efficient direct fit (Retrofit)Polycarbonate/ GlasshousingSMD Mid Power LED tube rod(with integral driver & alumn. heat sink ), on existing fixture.system lumen efficacy ≥ 100 lm/Watt output, internal surge protection of 2.5 KV ,THD < 20% ,p.f.≥0.95,CRI >80 , life time of minimum35000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 600mm , Min Lumens output 1800 lm LED Tube rod with Polycarbonate housing (E-17/87/17.2.1) 122 Providing & Fixing of IS 11037:1984markednon modular socket size flush type 180 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .(E-07/30/7.21) 123 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1200 mm Sweep (E-15/81/15.7.3) 124 P & F of Ding-Dong/Musical Chime Bell as per PWD specification for electrical works including making connection, testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . (E-07/30/7.26) 125 P & F of Ventilating fans, Capacitor start, Copper wounded, single phase with PVC impeller, ABS body, automatic openable louver shutter in existing opening including making connections, testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 250 mm sweep. (E-15/82/15.13.3). 126 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along withISI marked (IS:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR. 25 mm (E-02/1.4.2) 127 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR. 1x1.5 Sq mm (E-04/9/4.1.1 128 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR. 2x2.5 Sq mm + 1x1.5 Sq mm (E-04/4.1.7) 129 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR . 2x4 Sq mm. + 1x2.5 Sq. mm. (E-04/4.1.14) 130 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu purity purity >95%thimble etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .10 SWG G.I. (Hot Dipped ) (E-14/75/14.6.9) 131 Supplying & drawing PE insulated & PVC sheathed unarmoured Telephone Cable with 0.5 mm dia. Solid Annealed electrolytic grade bare Copper conductor as per IS:8130/84 & confirming tp TEC specification GR/WIR/06-03 March 2002 in existing surface or recessed conduit/casing capping including ferruling on each pair for identification etc. as required. For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 1-Pair (E-04/10/4.3.1) 132 Supplying, Drawing & Testing of 4 pair, 23 AWG solid bare Copper wire insulated witj HDPE, Category 6 A/Class Ea, U/FTP(Unscreened/Foiled twisted pair), 100Ώ Impedance, Indoor cable as per latest ammendments of ANSI/TIA/EIA-568 C.2 & ISO/IEC-11801 2nd Ed. The Copper conductor should br balance twisted in pairs, unscreened & Aluminium foil shielding of individual pairs protected by a low smoke zero Halogen (LSZH) (IEC-60332-1) jacket. Certified performance in a 4-connector configuration up to 100 Mtrs channel requirements & transmission frequencies up to 500 MHz should meet IEEE-802.3af & IEEE-802.3at for POE application. Cable should support Ethernet 10GBASE-T according to the standards in existing MS/PVC conduits/Casing Capping including making connections to information outlets & patch panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping & testing etc. as required. All as per pre approved by Engineer-In-Charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . (E-20/106/20.3.) 133 Supply & Laying following size B class ,G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories like bend, socket etc.for laying earth conductor/ strip / cable in ground/ surface/ recess as required.All as per pre approved by Engineer in charge.(Earth Excavation will be Paid Extra)All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annex ure A attached with this BSR . 32 mm dia. (E-14/75/14.7.4) 134 SITC of Monoblock motor pump set ISI marked (IS:9079-2002) with TEFC motor, motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011. with Stainless steel Impellor, Stainless steel shaft, Mechanical seal, Single/Three phase ( 240 - 440 V ) permanent split capacitor type (PSC), fitted with thermal overload protection, Including cost of hardware etc on existing platform complete. Pump shall have following HP Rating, phase, Head, minimum Discharge respectively complete in all respect. OEM shall have submitNABL / CPRI / ERDA accrediatedlab type test certificate before execution. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .1.0 HP E-21/115/21.7.2
