Tender For Burial Ground At Aiims Deoghar; 1 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drain (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, surplus excavated soils as directed, within a lead of 50 m. 2 All kinds of soil 3 Filling available executed earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. 4 Surface dressingof the ground including removing vegetation and in-equalities not exceeding 15 cm deep disposal of rubbish, lead up to 50 m and up to 1.5 m. All kinds of Soil 5 Supplying chemical emulsion in sealed containers including delivery as specified. 6 Chlorpyriphos/ Lindance emulsifiable concentrate of 20% 7 Diluting and injecting chemical imulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion): 8 Along the external wall below concrete or masonry apron using chemical emulsing @ 2.25 litres per linear meter including drilling and plugging holes etc.: 9 With chlorpyriphos/ Lindance E.C 20% with 1% concentration 10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 11 1:1.5 (1 Cement 1 1/2 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 12 Providingandlayinginpositionspecifiedgradeofreinforcedcement concrete,excludingthecostofcentering, shuttering, finishingand reinforcement - All work up to plinth level : 13 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 14 Reinforcedcementconcreteworkinwalls(anythickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments,posts andstruts etc. above plinth level up to floorfivelevel,excludingcostofcentering,shuttering,finishingand reinforcement : 15 1:1.5:3(1 cement : 1.5 coarse sand(zone-III) derivedfrom natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 16 Centeringand shutteringincludingstrutting, proppingetc. and removal of form for 17 Foundations,footings,basesofcolumns,etc.formass concrete 18 Lintels,beams,plinthbeams,girders,bressumers and cantilevers 19 Columns, Pillars, Piers, Abutments, Posts and Struts 20 SteelreinforcementforR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete upto plinth level. 21 Thermo-MechanicallyTreatedbarsofgradeFe-500Dor more. 22 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 23 Cement mortar 1:4 (1 cement : 4 coarse sand) 24 12 mm cement plaster of mix : 25 1:4 (1 cement: 4 fine sand) 26 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 27 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre . 28 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 29 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 30 Structural steel work riveted, bolted or welded in built up sections, trusses, and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. By 50X50X5m angle 31 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 32 1.00 mm thick with zinc coating not less than 275 gm/m* 33 Providing& Applyinghighqualityacrylicmodifiedresinbasedtexture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kg/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litre/10 sqm, complete as the direction of Engineer -in-Charge.
