Tender For Addn/ Altn To Md Accn At Rt Line Under Ge (West) Jrc; 1 Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick (below or above ground level complete. 2 Demolition of brick or stone masonary built in cement mortar complete 3 M&L brick work with sub-class B bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6. 4 M&LCement concrete type D 2, 1:4:8 (using 40 mm gradedstone aggregate) in sub base of flooring, hard standing,Manhole, drain etc. 5 M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions ofwalls shallnot exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls. 6 M & L for 25mm thick Sand coushening under paver block complete all as specified and directed. 7 M&L machine pressed precast coloured concrete coloured interlocking paver blocks any shape and size confirming of IS 15658 : 2006 of 60mm thick, M-35 laid and jointed with grey cement and pigment. 8 M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm gradedstone aggregate) cast in situ inkerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work. 9 Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc 10 M&L 10mm thick rendering in CM 1:3 onbrick/concrete surfaceas in ceiling and finishing the surface even and smooth with out using extra cement. 11 M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement. 12 M&L 15mm thick rendering on wall in CM 1:6 onbrick/concrete surfaceand finishing the surface even and smooth with out using extra cement. 13 Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises 14 M&L colouredGlazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4. 15 M/L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 SqM but not exceeding 0.18 SqMinfloors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. 16 Non - skid Ceramic tiles 7 to 8 mm thick area of eachtile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match infloors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. 17 All as per item No 16 above but in skirting over 10 mm thick cement plaster in CM 1:4. 18 M&L Machine cut kota stone slab flooring 18 - 20mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete. 19 M&L Machine cut kota stone slab flooring 18 - 20mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete. 20 Demolition of re-inforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in anypositionnot otherwise specifically provided for 21 Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete 22 M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to GdI IS-432 23 Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter. 24 M&L 20mm Granite (of any type) work(table rubbed and polished) in steps, jambs , pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement screed bed in CM 1:4 complete all as spd and directed. 25 Rounding/mouldingto edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc 26 Demolition of cement concrete above ground floor and paving exc 15 cm thick (below or above ground level complete . 27 M & L for water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:-(i) Application of two component acrylic modified cementitious coating.(aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or miling to remove cement laitance, existing coatings and achieve a gripping profile that is clean dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturers published literature should be strictly complied with, including but not limited to the following:-(bb) Chipping out any visible cracks in V-Groove pattern as applicable. Special attention on this part. Cleaning of cracks and then filling those cracks with SIKA latex SBR 100 putty/Dr fixit 302 SBR latex/ Perma Latex SBR/ FOSROC Nitabond SBR latex/ Asian Paints latex as required. Final cleaning of surface with power grinder, Wire brush, hair brush & vacuum pressure if required.(cc) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of SIKA Top Seal-107/ Brush bond FOSROC/ DR Fixit/ STP/CICO.(dd) Whilist the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of SIKA Top Seal-107/ Brush bond FOSROC/ DR Fixit/ STP/CICO of viscosity as per manufacturers instructions.(ee) Apply glass febric sheet of Sika Fab 1/FOSROC/ DR Fixit/ STP whilist the first coat is wet.(ff) Once touch dry, apply second coat of Acrylic modified Cementitious coating of SIKA Top Seal-107/ Brush bond FOSROC/ DR Fixit/ STP/CICO of viscosity as per manufacturers instructions on the entire area.(gg) Second coat shall be applied 6-8 hours of application of previous coat and in the direction right angle to the previous coat.(hh) The waterproofing coating should be taken to a height minimum 300 mm above the finished floor level on the vertical surface.(jj) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 hours drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking.(kk) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls.Admixture : SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO confirming to IS 2645.(ll) Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surface.Admixture : SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO confirming to IS 2645.(mm) All the corners and joints should be pretreated with an elastic waterproofing sealing tape withy a wooven bonding mesh on each surface and an elastic expansions zon be in the centre of Make Sika Seal Tape S/FOSROC/ Dr Fixit/ STP.(nn) The membrane has to be protected in accordance with the manufacturers recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturers recommendations.(oo) Waterproofing/Sunken floor treatment has to be carried out through applicators authorised.(ii) All the joints of pipes and traps within sunken portion shall be sealed properly by Epoxy sealant.(iii) All CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15 cm all around.(iv) The sunken portion shall be filled with PCC 1:5:10 type E2 (using 40mm stone aggregate) complete all as specified.(v) Providing drainage spout pipe GI 40mm dia bore light grate upto outside of outer wall (Approx 450mm to 600mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.(vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm grade stone aggregate as in flooring for laying floor finish all as specified. Note : Item No (iv), (v) & (vi) shall be measured and paid separately. 28 Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall, 29 M & L for 40mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc. 30 M & L 25mm thick cement concrete flooring type B-1, 1 :2 : 4, using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement. 31 M& L Cement concrete type E-2, 1:5:10 using 40mm graded aggregate in foundations filling and mass concrete as in sunken floor. 32 Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5sqm each 33 Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm each 34 Refixing of shutters in same opening exc 1 sqm and n exc 2sqm each with repairing , easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. Renewal of builders hardware articles. Wiremesh and builder hardware will be paid in respective items 35 S&F pressed steeldoor framewith one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm 36 S&F pressed steeldoor framewith one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm 37 M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles 38 Cutting holes in brick walls incement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick 39 S&F2nd class hardwood rail and style, factoy made plain,framed,panelled shutters (two panel) 35mm thick, with lock rails and panel of 9mm B. W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS : 1003 (Part-I), kiln seasoned and chamically pressure treated. 40 S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mitred and rebated bars any numbers. 41 Dismantling of unframed timber scantlingsin fillets, rails, posts, rafters, purlins,etc. under 40 sq. cm in section in any position 42 Dismantling boarding, any description, fixed in any position with nails 43 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size Frame size 50 x 100 mm for wardrobe, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made 44 S & F Factory Made Solid PVC Moulded Door Shutter With Core free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing. 45 Providing and fixing factory made 18mm thick solid, decorative, WPC(Wood Polymer Composite) laminated board of required size as in wordrobe shelf comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner with having minimum density not less than650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of board and fixing with solid, WPC(Wood Polymer Composite) batten as required size and fixed with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. 46 S&F Butt hinges,aluminium alloy anodised and fixed100 mm size ISI marked. 47 S&F in replacement 100 mm hasp and staple aluminium anodised including bolt to hinge plate and fixed with screw complete all as specified. 48 S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/ 49 S&F Extruded aluminium alloy handles fabricated type anodised 150mm size 50 Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube 51 S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out ofM.S.Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame at the site as per specification & drawing. 52 S&F Butt hinges,aluminium alloy anodised and fixed100 mm size ISI marked. 53 S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/ 54 S&F Extruded aluminium alloy handles fabricated type anodised 150mm size 55 M & L for Anodised Powder Coating(minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified 56 M & L Powder coated aluminium (Thickness of main aluminium section not less than 1.60mm and minimum thickness of powder coating 50 micron) for sliding window shutters including providing and fixing roller, three track system, locking arrangement fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws where necessary all complete as per architectural drawings and the directions of Engineer-in-charge. 57 M & L Powder coated aluminium anodised window and ventilator shutters (Gauged and glazed shutter), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) completeallasspecified 58 S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165 59 S&F Galvanisedmild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples. 60 M&L for 4.80mm thick sheet glass ordinary quality glazing with oil puttyin squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. 61 S&F Butt hinges, medium weight cold rolled 100 mm size ISI marked. 62 S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/ 63 S&F Extruded aluminium alloy handles fabricated type anodised 150mm size 64 S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified. 65 S & F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete. 66 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mm 67 S & F in repair for mild steel pipe 25 mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops,rollers etc as approved complete all as specified. 68 Providing and fixing solid PVC Kitchen Cabinet of size 1845 x 770 x 620mm at site made out of 18mm thick one side decorative lamination and other side balancing lamination sheet consisting of car case 18mm thick pvc sheet and provision of shutter made out of 18mm thick one side decorative lamionated PVC sheet all required brackets SS screw etc. the panel shall be febricated using adhessive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish as per make and specification mentioned as per drawing and specification approved by Engr in Charge. 69 Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. 70 Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. 71 S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. 72 S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. 73 Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar1:3 to ends or edges of shelves , for water tubing etc andmaking good, cutting exc 10cm girth but not exc 20cm girth in stone walls 74 Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittings complete. 75 S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I 76 S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair 77 S&F ball float valve brass with epoxy coated aluminimum rodfor 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe. 78 S&F in repair 15mm dia long body Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule 79 S&F in repair 15mm brass CP bath mixer for mixing hot & cold water screwed down for iron pipe and fixed. 80 S&F in repair 15mm brass CP WHB/Sink mixer swan neck for mixing hot & cold water screwed down for iron pipe and fixed. 81 S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. 82 S&F 15mm dia Brass stop valves chromium plated, fancy type with cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlons as specified and fixed in repairs. 83 S&F in replacement PVC cabinet size 450mmx325mmx120mm with looking mirror and making good the disturbed surface complete all as specified. 84 S&F in repairVitreous china wash hand basin (550X400mm) white, flat back excluding taps,including brackets &32mm waste cuppling complete all as specifed and directed. 85 S&F Vitreous China Water closet (Squatting pattern) Orissa Pattern size 580x 440 mm white with P or S trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairs complete. 86 S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs 87 S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified 88 Supply and fixed CP Soap dish, any type fixed to walls with plugs with chromium plated brass screws 89 Supply and fixing for glass Shelf with stainless steel railing and 8mm premium quality black glass shelf of size 450mm x 150mm complete all as specified and directed. 90 S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed. 91 M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed 92 S&F in repair brass chromium plated shower rose 125mm size complete all as spd and directed. 93 Supply in fixing in repairs sink with drainage board made Stainless steel 1mm thickkitchen or laboratory with plugs, washer and wastes pipe , including bedding in cement mortar on dwraf wall orincluding fixing cantilever brackets and connecting union pipe, over all size 915mm x 460mm bowl size 410mm x330mm x160mm. 94 S & F in replacement stainless steel kitchen plate rack, made out of 1mm thick stainless steel size 39 x 36 x 10 (Miinimum weight 8.50 Kg) with shelves and plate position as approved complete all as specified and directed. 95 Dismantlingof brick tiles single layer as in roofcovering complete all as specified 96 Demolition of mud in roofs any thicknessincludingplastering and leeping(whether full thickness removed or only a part thereof) all as specified. 97 Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd. 98 M&L PCC 1:2:4 type B0 using 12.5mm graded stone agg in padding using appropriate WPC as per manufacturers information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO onbrick/concrete surface, finishing the surface even and fair without using extra cement Complete all as specified and directed. 99 Supply and apply PU based waterproofing and heat reflecting system having following key performance properties: UV resistant and resistant to yellowing and weathering Highly elastic and crack bridging Non-toxic and VOC complaint water based coating One component ready to use Excellent adhesion on porous and non porous substrates Seamless waterproofing membrane Water vapour permeable Material shoud have below propertiesSolid content -60% (ASTM D 1644) Density (gm/cc)-1.30 (ASTM D1475) Elognation-350% (ASTM D 2370)Tensile strength N/sqmm-2.8-2.9 (ASTM D 2370) Solar reflective index -107 according to ASTM E 1980The installation company of roofing system should be trained and authorized by Manufacturer & installation to be carried out as per manufacturers approved method statement. All auxiliary & accessories involved during application should be supplied by single manufacturer as a part of system. Any component used which is not manufactured by the roofing manufacturer can only be used with official approval from manufacturer.System: Providing and applying primer over the prepared surface with Homeshield Roof kool & SealFirst coat:Material : Water = 1:1 by weightTotal thickness: ̴̴ 0.4 – 0.5 mmConsumption: 0.25 kg/m2.Reinforcement: Glass fiber meshSecond coat: Homeshield Kool & SealConsumption : 0.5 kg/m2.Third coat: HomeshieldKool & SealConsumption: 0.5 kg/m2. 100 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) 101 Dismantling of cast iron or reinforced concrete drain pipes of size 75-100mm dia, jointed in cement mortarandtakingout of trenches, if required. 102 S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete 103 S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls 104 S&F110mmPVC (SWR) bends 105 S&F75 mmPVC (SWR) bends 106 S & F for PVC 110mm (SWR) vent cowl 107 M&L for repairing of R.C.C projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applyingtwo coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engr-in-charge.(Note : Cost of form work and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed. 108 S&F Steel work as in tubular section for Post, Purline etc including special shaped washer , angle cleat, holdfast, gussete plate etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240cut or notched forming holes, without any attachment including drilling, fitting, riveting and or welding or connecting with bolts and nuts (incl rivet or nut and bolts) providing and fitting angle cleats Gussete plates etc also for welding plumbing, truing up and fixing complete as directed by Engr-in-Charge. 109 M&L pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with J or L type or cranked hookbolts complete as directed by Engr-in-charge. 110 M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters,nosingtosteps includingembedinginconcrete and screwing etc. wind ties for roofincluding securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling,boltingor riveting, etc., and similar work conforming to Fe-290 Gde E-165 111 M&L for prepration of new steel surface of any description, over 10cm in width or girth,not otherwise described and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc complete all as specified and directed 112 M & L for prepration of new steel surface of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc. 113 Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out soft/ lose soil. 114 Excavation in post holes each nexc 0.50 cum , getting out, returning filling in and ramming earth or broken rubble mixed with earth in layers not exceeding 25cm in soft/loose soil 115 M & L for PCC (1:2:4) typeB-2 (using 40mm graded crushed stone aggregates ) lean concrete as in foundation, filling and mass concrete of post complete all as specified . 116 M&L Broken stone or boulders as in hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered, rammed to a true surface etc complete all as specified and directed 117 M/L 100mm thick cement concrete 1:4:8, type D-2 using 40mm graded stone aggregate. 118 M&L machine pressed precast coloured concrete coloured interlocking paver blocksany shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment. 119 M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm gradedstone aggregate) cast in situ inkerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work. 120 S&F Steel work as in tubular section for Post, Purline etc including special shaped washer , angle cleat, holdfast, gussete plate etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240cut or notched forming holes, without any attachment including drilling, fitting, riveting and or welding or connecting with bolts and nuts (incl rivet or nut and bolts) providing and fitting angle cleats Gussete plates etc also for welding plumbing, truing up and fixing complete as directed by Engr-in-Charge. 121 M&L pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with J or L type or cranked hookbolts complete as directed by Engr-in-charge. 122 M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters,nosingtosteps includingembedinginconcrete and screwing etc. wind ties for roofincluding securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling,boltingor riveting, etc., and similar work conforming to Fe-290 Gde E-165 123 M&L for prepration of new steel surface of any description, over 10cm in width or girth,not otherwise described and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc complete all as specified and directed 124 M & L for prepration of new steel surface of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint and apply two coat of synthetic enamelpaint over a coat of red oxide primer etc. 125 Returning, filling in , including spreading, levelling , watering and well ramming in layers not exc 25 cm thick by using hard/dense soil as in low line area as directed by Engr-In-Charge . 126 Removing excavated soils n.exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point. 127 Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etcfor shafts, wells, cesspits , manholes pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soilcomplete all as specified and directed. 128 Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or Reinforced) set in cement mortar all as spd and directed 129 M &L for 150mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as spd and directed 130 M&L for concrete bed for 150mm in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) to drain pipes including packing under,haunching against the sides of pipes after they are laid and testedcomplete all as specified and directed. 131 Demolition of re-inforced cement concrete of any description and in anypositionnot otherwise specifically provided for 132 M&L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast RCC manhole / septic tanks ,drain,covers including all form work and setting in CM 1:4 all as specified and shown on drgs. 133 M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to GdI IS-432 134 Material and labour for cement concrete 1:2:4 Type B-1using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by the Engineer-in-Charge. 135 M & L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge 136 M & L for applying white wash of 3 coats on ceiling incl preparation newly plastered surfaces as specified and directed. 137 Complete removal of existing treatment andapplying Two coat of white wash on ceiling incl preparation old plastered surfaces as specified and directed. 138 M & L for applying white wash of 3 coats on wallsincl preparation newly plastered surfaces as specified and directed. 139 Complete removal of existing treatment on wall andapplying Two coat of white wash incl preparation old plastered surfaces as specified and directed. 140 Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified. 141 Complete removal of existing treatment on wall andapplying Two coat of Oil distemper (white or tinted) on old plastred surfaces including preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed by Engineer-in-Charge. 142 Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paintover one coat of cement primer complete all as specified. 143 M&L for Complete removal of existing treatment on wall andapplying Two coat of of cement base paint on old plastred surfaces including preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed by Engineer-in-Charge. 144 Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors 145 Taking down unserviceable Submain/Cableof any size as directed by Engineer-In-Charge. 146 Taking down main switch / DB as directed by Engineer-In-Charge. 147 M & L for sub main wiring with four single core PVC insulated and unsheathed cable 10 sqmm with multi stranded copper conductor , FRLS type cable drawn throughand including PVC concealed conduit of suitable size complete with all accessories alongwith provn of 2 run of 10 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire. 148 M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn throughand including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one length) 149 M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistrandedcable as earth wire including sunken type pressed steel terminal boxes of thickness 1.6 mm thick and plastic laminated white / coloured top sheet cover 3.0 mm thick for:One light / fan/bell pointcontrolled by one, one way switch complete all as specified.. 150 One 3 pin socket out let 5 Amps on same board with other switches complete all as specified.. 151 One 3 pin socket out let 5 Amps on the independent board complete all as specified.. 152 All as per item No 149 above but with 2.5 sqmm multistranded copper multistranded conductor FRLS cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board complete all as specified. 153 S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, AC complete all as specified. 154 S & F switch Piano 15 Amps, flush button type, SP, one way, 230 Volts, AC complete all as specified. 155 S & Fsocket out let multipurpose 5 pin 5 Amps,230 Volts complete all as specified. 156 S & Fsocket combination ,6 pin ,15 amps, flush type, multipurpose, 230 V complete all as specified. 157 Supply and fix bell push flash piano type 5 amps complete all as specified.. 158 Supply and fix bell ding dong 230 Volts AC single pole complete all as specified.. 159 M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified. 160 Taking down and refixing the same main switch / DB along with MCBs and elctrical connection all as directed by Engineer-In-Charge. 161 Supply and fix MCB DB, TPN 6 way double door Vertical type suitable for mounting of MCCB as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates conforming to Osafe of HPL / Acti 9 series of Schneider /equivalent in Havells/Hager/L&T/Siemens completeall as specified and directed. 162 Supply and fix MCCB 63 Amps 4 pole415 Volt,25 KA breaking capacity conforming to Osafe of HPL / Acti 9 series of Schneider /equivalent in Havells/Hager/L&T/Siemens complete all as specified and directed . 163 Supply and fix Sheet metal DB,double door,SPN 8 way for MCB, 240 volt with 200 amps rated bus bar , neutral bar / connectors suitable copper thimbles , lugs etc complete all as specified and directed. Make : EKINOX3 series of Legrand/Acti 9 metalic series of Schneider /Osafe series of HPL/Metallica of Havells/Hager/L&T/Siemens 164 S & F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type conforming to Osafe of HPL / Acti 9 series of Schneider /equivalent in Havells/Hager/L&T/Siemens completeall as specified and directed. 165 Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type conforming to Osafe of HPL / Acti 9 series of Schneider /equivalent in Havells/Hager/L&T/Siemens complete all as specified and directed. 166 M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all as specified and directed. 167 S & F LED bulb 12 W complete all as specified and directed. 168 Supply and fix of Microwave Sensor enabled Integral LED 4 ft luminaire with extruded housing and Opal diffuser ith ABS end caps. The luminaire should have a color consistency SDCM < 5, CRI > 80 and CCT of 6500K. The luminaire shall be compliant with IP20 classification. Luminaire shall be designed to emit at least 2000 nominal lumens at a system efficacy of at least 100 lumen/watt with a maximum system wattage of 20 Watts. Fixture should cover upto 5 mtr sensor radius coverage area with 120 degree angle after 17 to 30 seconds & 30% light output in case of non-occupancy.The electronic driver used shall have a power factor >0.9 and THD <10% and suitable for an operating voltage range of 140-270V AC. Manufacturer shall have in house lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameterscomplete all as specified and directed .. Havells Cat no LUMILINESMART20WLED865PCWH equivalent in Signify/Wipro 169 S& F in replacement LED tube set (fitting) 20 Wuse and through type withinternal surge protection device of 4 KV with voltage band 140-280V with LED rod with fixture box type and making electrical connection to ceiling rose all as directed 170 S & F SITC of high-quality integrated LED Street Light with a minimum system lumen of4750 Lm and system wattage not exceeding 45W with a nominal efficiency 105 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI >70. The housing should be of non-corrosive high-pressure die-cast aluminum with high efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with PF > 0.95. Lifetime of 50K hours @L70. The Luminaire should have Powered by integral, Isolated LED electronic driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection (Operation at 440 V AC), Over Voltage protection, Surge Voltage protection upto 4 kV.Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/ULaccredited lab to verify above parameters complete all as specified and directed.. Havells Cat noENDURASUNBEAMSL45WLED757SASYTOPCSENSO equivalent in Signify/Wipro 171 Supply and fix of hexagon shaped LED bulkhead industrial luminaire with Pressure die cast housing and Polycarbonate diffuser and silicon gasket. The luminaire should have a color CRI > 80, and CCT of 5700K. The luminaire shall be compliant with IP66 & IK 10 classification. Luminaire shall be designed to emit at least 1000 nominal lumens at a system efficacy of at least 100 lumen/watt with a maximum system wattage of 10 Watts. The electronic driver used shall have a power factor >0.95 and THD <15% and suitable for an operating voltage range of 180-270V AC and 4 Kv inbuilt surge protection. Manufacturer shall have in house lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Havells Cat no HEXAFT10WLED857SSYMBOPC equivalent in Signify/Wipro 172 Taking down existing Ceiling fancapacity/type carefully and refixing the same with gutties, nuts boltss if required complete all as specified and directed. 173 Taking down existing Geyser any capacity/type carefully and refixing the same with replacement of PVC connection/Steel connection and anchor fastenerpipe if required complete all as specified and directed. 174 Taking down existing electric/electronic energy meter any capacity/type carefully all electric wire/submain complete and refixing the same, incl electric connection with new gutties/anchor fastener if required complete all as specified and directed. 175 Supply & fIX Water Heater storage type, five star rated, electric operated, 25 Ltr capacity 230Volt AC Supply with PVC Connection pipe Superior quality(HOT & Cold water ) including Plug top 15 Amp, NRV complete with necessary water connection and electrical connection complete all as specified and directed. 176 Supply and fixing ceiliing fans in replacement complete with blades, down rod , electronic regulator switch type5 step and accessories 230V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. 177 Supply and fix in replacement PVC Exhaust fans AC single phase 230/ 240 V of size 230 mm sweepas required for fixing and electrical connection upto ceiling rose complete all as specified and directed. 178 Supply and fix exhaust fan, Metal body heavy duty AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers incl opening of hole in wall and matching with existing finish all as specified and directed. 179 Supply and laying XLPE insulated , armoured electric cable heavy duty with aluminium conductor , 1100 volts UG cable of size 4 Core 50 Sqmmm, 180 Supply and lay burnt bricks sub class B standard size laid across the cable in trenches as protection to the cable all as specified and directed. 181 Supply and laying GI Tube Med grade 50mm dia all as specified and directed. 182 M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DBby means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part I
