Tender For Certain Repairs To Flooring,Sanitary & Plumbing Items Including Toilets Etc In Otm & Md Accn At Y Stn Under Age B/R-I Of Ge Satwari; 1 Notes : (1) Work will be carried out upto 4th storey of bldgs and quoted rates of items shall be deemed to include the cost ofnecessary formwok and scaffolding required as per site conditions. 2 Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each and removing from the site complete all as specified & directed. 3 Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 4 Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each includingcutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed. 5 Demolition of cement concrete (un-reinforced) in ground floor to 4th floorand pavings n exc 15 cm thickness (below or above ground level ) and removingthe rubbish from the work site to out side defence premises complete all as specified and directed. 6 Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 7 Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed. 8 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceabletiles to store and rubbish off the premises complete all as specified and directed 9 S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 10 S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 11 S&F 35 mm thickfactory made 2nd class hard wood, plain, framed, panelled shutters (two panels) with lock rail and panel of 9mm thick BWP commercial plywood .The size of rail and stiles as per IS: 1003(Part-1), kiln seasoned and chemically pressure treated, fitted to chowkats complete all as specified and directed. 12 S&F factory made 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framingplain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed 13 M&L for 30mm thick factory made flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed. 14 S&F in repair solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed. 15 S&F factory made solid panel PVCdoor shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C ‘C’ channelhaving a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed. 16 S&F 100mm long stainless steel butt hinges, fixedwith screws complete all as specified and directed 17 S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed. 18 S&F aluminium anodised , cast type handle 100mm size complete all as spcified and directed. 19 S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed. 20 S&F140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. 21 S&F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate including fixing to pressed steel frames with necessary welding work complete all as speciied and directed 22 Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed.Note:- For measurement superficial area in elevation shall be measured. 23 S&F factory made 18 mm thick (+0.7mm) celuka PVC ply. One side prelam and other side plain 18mm thick celuka PVC ply for kitchen cabinet shutter/shelf/partitions/drawer and also manufactuerers test report and test certificate is mandatory with each and every supply of the material complete as per manufactuers specifications and drawing and as directed . 24 S&F factory made 5mm thickPVC pannelingfor back side (wall side) of kitchen cabinet shutter/Wardrobe / partition/shelf and also manufactuerers test report and test certificate is mandatory with each and every supply of the material complete as per manufactuers specifications and drawing and as directed . 25 S&F stainless steeldesigner handle ( heavy type) 125 mm size, fixed in drawers or shutters of cupboards complete all as specified and directed. 26 S&F Rolling channel plate for kitchen cupboards complete all as specified anddirected. 27 S&F steel fasteners of size 75 mm long, drilled and fixed to walls complete all as specified and directed. 28 S&F pressed steel cup board frame of size 60mmx40mm, made out of mild steel sheet 1.25mm thick with rebate 20mm wide and 12mm deep and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed. 29 M&L for prelaminated MDF board (exterior grade) 19 mm thick as in shutters /shelves ,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including lipping (15mm thick three sides and 20 mm thick lipping hinge side around the shuttercomplete all as specified and directed. 30 S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20gauge with stainless steel brackets near toends with stainless steelfinialsat both ends and necessary fittings complete all as specified and directed. 31 S&F steel window 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS pintle hinges of size 75 mm x 12 mm 2 No per leaf fabrication complete all as specified in per drg No CEPZ/TD-324,325 complete all as specified and directed. 32 M&L for framed work such as grills , gratings etc with ends of bars shouldered and /or riveted or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters: walk ways , railings frame work of water tanks and similar work confirmingto Fe290, Gde E-165 complete all as specifiedand directed 33 Hacking out old broken glass (any thickness, size, quality or description)from wooden/ metal frame including punching or drilling out old glazing pins/spring clips andfixing new onescomplete all as specified and directed. 34 M&L for 3 mm thick, plain sheet glass, ordinary quality and glazing with glazing pins, oil putty or with any type of beadsin squares n. exc 0.5 sqm each pane complete all as specifiedand directed. 35 S&F 3 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each panecomplete all as specified and directed. 36 S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed . 37 S&F in repair Bib tap 15 mm bore,standard of PTMT, any colour, high pressure, screwed for iron pipe and fixed (Min weight 90 gms) complete all as specified and directed 38 S&F in repair angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 39 S&F in repair bib tap , long body, chromium plated, fancy type, cast copper alloy,screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed. 40 S&Fin repair PVC waste pipe 32mm bore for sink/WHB of required lengthcomplete all as specified and directed 41 M&L for 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite ,making hole for gas pipe over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified anddirected 42 M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as complete all as specified anddirected . 43 M&L for RCC 1:1.5:3 (nominal mix) type A1 (using 20 mm graded crushed stone aggregates)as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed . 44 M&L for Mild steel TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 45 M&L for use and waste of form work to softfits of suspended slabs such as roof slabs , floor slabs , landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed. 46 M&L for use and waste of form work to edge of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls , floor and roof and not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work exc 10cm but n. exc 20 cm wide for fair finished surfaces of concrete complete all as specified & directed. 47 M&L for plain cement concrete 1:2:4 ,type B1(using 12.5mm graded crushed stone aggregates)as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed. 48 S&F in repair vitreous china wash down water closet pan (pedestal pattern)white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinges and P or S trap device complete all as specified and directed 49 S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron P or S trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed 50 S&Fin repair PVC connection 15 mm x 450 mm including PVC check nut at both ends complete all as specified and direced. 51 S&Fin repair PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and direced. 52 S&F in repair full pedestal for WHBcomplete all as specified and directed 53 S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC L bend and handle including brackets complete all as specified and directed 54 S&F in repair central hole basin mixer without popup waste system with 450mm long braided hoses, screwed down for 15mm bore iron pipe complete all as specified and directed. 55 S&F in repair wall mixer 3-in-1 system with provision of overhead & hand shower complete with 115mm long bend pipe, connecting legs & wall flange fancy type complete all as specified and directed. 56 S&F in repairbrass chromimium plated sink mixer swan neck with swinging spout (wall mounted model) with connecting Legs & wall flanges complete all as specified and directed. . 57 S&F in repair 2 in 1,angle valve with flange,cast copper alloy , fancy type, chromium plated, screwed down for high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and dircted. 58 S&Fin repair 15mm boreStop valves, cast copper alloy,fancy type, chromium plated with long shankandcup (concealed type) screweddown, high pressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed , complete all as specified. 59 S&F in repair pillar tap, chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed. 60 S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed. 61 S&F in repair door closer hydraulically regulated, Aluminium (extruded section body), designation No 3, universal type suitable for door shutter 851mm to 1000mm width and weight between 61 to 80 kg complete all as specified and directed. 62 M&L for repair/ easing of wooden door, any type (glazed or panelled) by trimming the sides of door shutter where rubbing with chowkhat, unscrew the hinges & screws and fixing the screws after lifting the shutter including tightening the wire mesh complete all as specified and directed. 63 M&L for repairing aluminium shutters including tightening and making good usingrubber/beads and others small fixtures/fittings i.e handles, stopper etc( if required) and refixing by making the shutters serviceable complete all as specified and directed . 64 S&Fbrass mortice lock, vertical type, size 100 mm, 4 levers complete all as specified and directed. 65 S&F aluminium powder coated (coating not less than 50 micron) door frame and door shutter,door frame of hollow section 101mm x 44.0mm x thickness not less than 1.53 mm & hollow section of stiles of glazed shutter 85mm x 44.45mm x thickness not less than 1.56mm having grooves for aluminium beading and top rail of hollow section 83.5mm x 44.45mm x thickness not less than 1.50mm, lock rail of hollow section 83.5mm x 44.45mm x thickness not less than 1.50mm and bottom rail of hollow section 83.5mm x 44.45mmx thickness not less than 1.50mm ,one derived handle 300mm long,100mm long butt hinges - 4 Nos, aluminium floor type hydraulic door closer, aluminium mortice lock 65mm, 4 levers of Godrej pattern andrubber packing, aluminium beadingcomplete all as specified anddirected. 66 M&L for aluminum powder coated (coating not less than 50 micron), sliding window, three track with stainless steel mosquito proofingwith window style of section 44.4mmx44.5mmx 2.0mm thick and frame of section 101.60 x 44.45 mmx 1.20mm thicknessincluding 4.0 mm thick coloured/tinted/frosted glass panes & stainless steel wire mesh of aperature 0.63mm & all necessary fittings and fixtures complete all as specified and directed. 67 S&F Powder coated aluminum (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators,frame work & partitions including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately ) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS :1285, fixing with dash fasteners of required dia and size, including neccessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as specified and the directed .. 68 S&F aluminium powder coated (coating not less than 50 micron) door frameof hollow section 101.60mm x 44.45mm x thickness not less than 1.20 mmfixed with floor, ceiling, walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fastenerscomplete all as specified and directed. 69 M&L anodised aluminium grills (coating not less than 50 micron) , 6mm diaand size 100 x 100mm, fixed into aluminium windowcomplete all as specifed and directed. 70 M&L for 5.5 mm thick, tinted sheet glass ordinary quality and glazing with oil putty or with any type of beads (supplied alongwith shutters) in squares exc 0.5 Sqm in each pane complete all as specified and directed. 71 S&F 4mm thick aluminium composite panel (coloured sheet)including necessary accessories for fitting complete all as specified and directed. 72 S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made out of mild steel heavy duty & fixed complete all as specified and directed. 73 S&F in repair 12 mm thick sheettoughened glass (tinted/frosted/plain) as in partition wall/door/window including fixing with necessary stainless steel hinges and handles, lock, hydraulic door closercomplete all as specified anddirected. 74 S&F in repair hand shower 120mm round shapemulti flow with cascade effect (ABS Body chrome plated with gray face plate) with rubit cleaning systemcomplete all as specified and directed 75 S&F in repair flexible tube 12mm dia,1.50 metre long with chrominium plated nuts complete all as specified and directed. 76 S&F in repair Overhead Shower 200X200mm , single flow (ABS Body Chrome Plated with Gray Face Plate) with rubit cleaning system with shower arm casted 190mm long light body round shape for wall mounted showers with flange & 100 mm long CP nipple complete all as specified and directed. 77 S&F in repair EWC vitreous china, twin action, one piece wash down water closet pan, coloured of size 660mmx365mmx765mm with Soft Close Duroplast Seat Cover,Strap 300mm & accessories ,complete all as specified and directed. 78 S&F Vitreous china urinal of size 375x390x590mm,whiteincluding providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe andchromium plated spreader including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm borecomplete all as specified and directed. 79 S&F Vitreous china urinal of size 360x330x740mm,white with sensorincluding providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe andchromium plated spreader including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm borecomplete all as specified and directed. 80 S&F in repair chromium plated spreader for urinalcomplete all as specified and directed. 81 S&F in repair 8 to 10 mm thick toughened glass urinal partition of standard sizeincluding fixing accessories complete all as specified and directed . 82 S&F in repair chromium plated bottle trap (with internal partition) 32mm size with 250mm & 190mm long wall connection pipe & wall flange complete all as specified and directed. 83 S&F in repair vitreous china counter wash basin, size 560x470x190mm, oval shape , white, to be fixed on counter/ RCC slabincludingchromium plated waste coupling, 32mm waste pipe,bottle trapcomplete all as specified & directed 84 S&F in repair stainless steel shower panel, body material chrome plated stainless steel, anti finger print, movable ABS hand shower, brass spout, brass facet body with thermostat mixer, multifunction water diverter for top shower, body jets, spout 40cm stainless steel braided hose, 1.5cm stainless steel double locked flexible hoses and all necessary fittings complete all as specified and directed. 85 S&F in repairbrass chromium plated tubular towel ringof 150mm dia, fixed with CP brass screwsincluding plastic beads complete all as specified and directed. 86 S&F in repair brass chromium plated tubular towel rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed. 87 S&F in repair stainless steel peg set of six,rust resistant complete all as specified and directed. 88 S&F in repair stainless steel square foldable towel rack,600mm size complete all as specified and directed. 89 S&F in repair sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. 90 S&Fin repair corner glass shelf of size not less than 30cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed . 91 S&F in repair frameless bevelled edge mirror of 5mm thick selected quality glass, mounted onwall and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed 92 S&F in repair stainless steel lock grating plain/hole, 100mm dia including embeding in tiles with white cement complete all as specified and directed. 93 S&F in repair brass chromium plated shower rose 125 mm of dia with arm and with or without swivel joints to steel pipe or union complete all as specified and as directed. 94 S&F in repair vitreous china wash hand basin, white, flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including cast iron brackets, brass chromium plated waste coupling 32mm bore, waste pipe PVC 32mm bore complete all as specified and directed 95 M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent).Base coat: Berger HS Latex plus (or equivalent) both on wall (upto 1 mtr min height) and floor.Consumption base coat: 0.3 kg/sqmReinforcement: Glass fiberSecond and Third coat: Latex sheild 2K (or equivalent) both on wall (upto 1 mtr min height) and floor.Consumption top coat: 3 kg/sqmSystem requirements: density: 2.00 kg/ltrcompressive strength: 0.5 N/mm².• Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent).• Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft.• All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry including cleaning ofRCCsurface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc complete all as specified and directed . 96 M&L for rendering 10mm thick in cement mortar 1:4 mixed with water proofing compound on roof surfaces , surface finished even and smooth without using extra cement complete all as specified and directed. Note:- water proofing compound will be measured and paid separately 97 M&Lfor plain cement concrete 1:5:10, type E2 (using 40mm graded crushed stone aggregates)as in mass filling in sunken floor of toilets complete all as specified and directed. 98 Supply only liquid water proofing compound. 99 S&F 20 mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spoutto pour out residual water out from the treated areacomplete all as specified and directed . 100 M&L for capillary rise treatment of walls with following specification:-Base coat: Berger HS Latex plus or equivalent in make specified in PSConsumption base coat: 0.3 kg/m2Second and Third coat: Latex sheild 2K or equivalent in make specified in PSConsumption top coat: 3 kg/m2System requirements: density: 2.00 kg/ltrcompressive strength: 0.5 N/mm2. 101 M&L for dismantling of water tank of capacity exc 500 ltrs but n. exc 1000 ltrs and removing complete all as specified and directed. 102 M&L for dismantling of water tank of capacity exc 250 ltrs but n. exc 500 ltrs and removing complete all as specified and directed. 103 S&F Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixedin position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipeor brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed. 104 S&F Rotational moulded polyethlene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixedin position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipeor brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed. 105 S&F in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and directed. 106 Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and directed. 107 Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and directed. 108 S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall/ ceiling or laid in floors complete all as specified and directed 109 S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall/ ceiling or laid in floors complete all as specified and directed 110 M&L for cutting (in brick walls) chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting n.exc 10cm girth complete all as specified and directed. 111 Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed 112 S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 113 S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 114 S&F UPVC (SWR) type B, bends any radius, 75 mm bore complete all as specified and directed 115 S&F UPVC (SWR) type B,bends any radius, 110 mm bore complete all as specified and directed 116 S&F UPVC (SWR),type B, junction single, (single T)equal or unequal for 75 mm bore complete all as specified and directed 117 S&F UPVC (SWR),type B, junction single, (single T) equal or unequal for 110 mm bore complete all as specified and directed 118 S&F in repair UPVC (SWR) type B, floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed. 119 S&F in repair UPVC (SWR) type B,gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. 120 S&F UPVC (SWR) type B,vent cowl 75 mm dia complete all as specified and directed. 121 S&F UPVC (SWR) type B, reducers 110 mm dia complete all as specified and directed. 122 Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removingunserviceable material from work site to outside defence premises complete all as specified and directed. 123 M&L for brick work with sub class B bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed. 124 All as per Srl item No -123 here-in-before but except bricks complete all as specified and directed. 125 M&L for brick work with old size sub-class B bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed . 126 M&L for glazed ceramic coloured digital tiles,450x300x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. 127 M&L for 7 to 8mm thick non skid coloured digital ceramicjoint less tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:4 complete all as specified and directed. 128 M&L for 7 to 8mm thick non skid coloured digital ceramicjoint less tiles (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding0.18 sqm, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. 129 M&L for 7 to 8mm thick non skid coloured digital ceramicjoint less tiles (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding0.38 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:4 complete all as specified and directed. 130 M&L for 7 to 8mm thick non skid coloured digital ceramicjoint less tiles (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding0.38 sqm, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. 131 M&Lfor 8 to 9 mm thick vitrifiedceramic colourededge cut, joint free tiles (square/ rectangular) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified anddirected . 132 M&Lfor 8 to 9 mm thick vitrifiedceramic coloured , edge cut, joint free tiles (square/ rectangular) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified anddirected. 133 M&Lfor 8 to 9 mm thick vitrified double chargedceramic colourededge cut, joint free tiles (square/ rectangular) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified anddirected . 134 M&Lfor 8 to 9 mm thick vitrifieddouble charged ceramic coloured , edge cut, joint free tiles (square/ rectangular) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified anddirected. 135 Dismantling oftimber scantlings40 Sqcm and over in section, framed work,in any position complete all as specified and directed 136 Dismantiling of mild steel/AC (corrugated, semi-corrugated, etc.) sheets in roof coverings complete all as specified and directed 137 S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI basedcorrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . 138 S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI basedplain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed . 139 S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc confirmimg to Fe 290 (Gde E -165)complete all as specified and directed . 140 S&F in repair kit dual flush siphon for one piece toilet seat with advance high pressure float valve with toilet repair kit Abs push chrome plated button complete all as specified and directed . 141 S&F in repair urinal sensor kit/battery box/sensor eye/automatic flusher complete all as specified and directed . 142 Demolition of stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed . 143 S&F machine cut kota stone slab in flooring, treads of steps(one piece including rounding/ mouldings of edges of treads), 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed. 144 M&L for machine cut kota stone slab 15-18 mm thick in riser of steps, skirting , dado and pillar, laid and jointed with grey cement slurry mixedwith pigment to match the shade of the slab including rubbing, cutting and mirror polishing over and including 10 mm thick rendering in cement mortar 1:4 after roughing surfaces of old concrete /any type of plaster by picking sweeping down with water to remove dust etc complete all as specified and directed. 145 S&F in repairsinks , madeof 1mm thick stainless steel,overall size of sink 495mm x 420mm with bowl size 410mm x 330mm x 160mm,plugs, washers, waste pipe , union, CP waste coupling and cantilever brackets embedded in cement and sand mortar in wallcomplete all as specified and directed. 146 M&L for rendering 15mm thick in cement mortar 1:4 on concrete surfaces of roof finished even and fair including mixing of water proofing compound as per manufacturers instructions complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only. 147 Complete removal of existing water proofing treatmentof any description including under layer, taking down of cement plaster/demolition of cement concrete of any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel bushes and cleaning with water to remove all loose dirt/dust and apply water proofing treatment in the following sequences :-(a)Applying 1st course of bituminous primer confirming to IS-3384 @ 0.4 Kg/sqm. Cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely.(b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm.(c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.0 Kg/sqm with 160 Grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to belaid with LPG torch and overlap sealed and finished neat complete all as specified and as directed .(d) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer. 148 M&L for applying two coats of aluminum paint over the APP membrane complete all as specified and directed. 149 M&L for machine pressedcement concrete tiles 20cmx20cmx20mm thick, with grey cement and pigment, set ,jointed and pointed in neat cement slurry as in floors/roof surfaces, laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed 150 DismantlingWall and ceiling boards (fibre,pulp, insulation) or insulation boards/ slabs/ blankets, any thickness, including cover fillets etc complete all as specified & directed. 151 S&FGI snap grid frame work (Grid size 605mm x 605mm) for false ceilingconsisting of main runner T of size 24mm x 32mm and 0.3mm thick , Secondary runner T of size 24mmx25mm and 0.3mm thick,GI angle24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clipsincluding Gypsum ceiling tilesof size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap gridcomplete all as specified and directed .. 152 M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floor/hard standing complete all as specified and as directed. 153 M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. 154 M&L for machine pressed chequered cement concrete tiles 30cmx30cmx25mm thick, with grey cement and pigment, set ,jointed and pointed in neat cement slurry as in floors, laid over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed. 155 M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in sub base to floor/hard standing finished even and fair complete all as specified and as directed. 156 M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all as specified and directed. 157 M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces, surface finished even and smooth without using extra cement complete all s specified and directed. 158 M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed. 159 M&L for 50mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fairincluding raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed . 160 M&L for repairing of concrete surfaces such asbalcony, chajjas, upward or downward facia , column, pillar, ceiling and similar items of width n. exc 200 mmwith plain cement concrete 1:2:4type B-0 (using 12.5mm thick crushed stone aggregates) or with 15mm thick renderingin cement mortar 1:3 without using extra cement,surfacefinished even and fair(as per site requirement)complete all as specifiedand directed.(Note:-Quoted rated shall be deemed to include:- (i) Formwork and scaffolding required & taking down or dismantlingas per site requirement (ii) The work is to be executed upto 4th storey building 161 M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed 162 M&L for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described by rubbing with sand paper or grindingby hand grinderto make surface even and smooth & apply primer where required and applying one coat of synthetic enamel paint complete all as specified and directed. 163 M&L for preparation of new or previously untreatedwood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 164 M&L for preparation of old painted wood and wood based surfaces of any description over 10cm width or girth not otherwise described by grinding the uneven surfaces and necessary filling of putty (as and where required) to make surface even and smooth and applying one coat of synthetic enamel paint complete all as specified and directed. 165 M&L for preparation of old decorated concrete/ plasteredsurfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots,rubbing with sand paper and applying one coat of oil emulsion distemperincluding making good uneven surface/holes with wall care putty(where ever required) complete all as specified and directed. 166 M&L for preparation of old decorated concrete/ plasteredsurfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots,rubbing with sand paper and applying two coats ofwhite washcomplete all as specified and directed. 167 M&L for preparation of old decorated surfaces of ceilings by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying two coats of white washcomplete all as specified and directed. 168 M&L for preparation of old decorated concrete/ plasteredsurfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots,rubbing with sand paper and applying two coats of oil emulsion distemperincluding making good uneven surface/holes with wall care putty(where ever required) complete all as specified and directed. 169 M&L for complete removal of existing treatment by scrapping down with machine of wall surfaces complete all as specified and directed. 170 M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of wall care putty 1 to 2 mm thickand one coat of primer complete all as specified and directed. 171 M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic exterior emulsion paint over one coat of wall care putty 1 to 2 mm thick and one coat of primer complete all as specified and directed. 172 M&L for preparation of old decorated plastered /concrete surfaces of walls andapplying two coats of cement base paint over one coat of primer complete all as specified and directed. 173 M&L for preparation of new plastered or unplastered surfaces of walls, chajjas, fascia, face of columns, beams etc. andapplyingtwo coat of weather proof exterior emulsion paint over one coat of wall care putty of 1 mm thick complete all as specified and directed. 174 M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over two coats of wall care putty 1 to 2 mm thick each and one coat of primer complete all as specified and directed. 175 M&L for preparation of newplastered/concrete surfaces of walls andapplying two coats of cement base paint over one coat of primer complete all as specified and directed. 176 M&L for preparation of new plastered or unplastered surfaces of ceilings and applying two coats of white washcomplete all as specified and as directed. 177 M&L for preparation of old decorated concrete/ plasteredsurfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots,rubbing with sand paper and applying one coat of weather proof exterior emulsion including making good uneven surface/holes with wall care putty(where ever required) complete all as specified and directed. 178 Dismantling boarding of any description, fixed in any position with screws complete all as specified and directed. 179 M&L for 5mm thick prelam PVC sheet in strips & channel feathered at the edges for fixing on solid PVC wall lining, Insulated PVC wall lining, and Solid PVC partitions inclusive of solvent cement and fixing at site complete all as specified and directed. 180 M&L for grubbing up vegetation, small trees from roots, clean the loose dirt with water and repair the same portion with cement mortar 1:3, touchup with same finish, area not exc. 0.10 sqm each adjacent to CI pipe upto 4th storey building with necessary scaffolding/ ladder complete all as specified and directed.. 181 Surface dressing not exc 30cm deep and averaging 15cm deep in any type ofsoil, adjacent to plinth protection of buildings includinguprooting of tiny trees, tree cutting, cleaning, levelling and removingdebris to a distance not exc 50 m complete all as specified and directed.
