supply of Probable Items With Approximate Quantities For The Smart School At Sylee T.E. Primary School, Under Mal Development Block, District Japaiguri.- 1 (Item No. 4(b), Page No. 24 of PWD Building Schedule (2017) (3rd Corrigendum)Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.i) NB Variety 2 (Page No. 15, Item No. 7(b),of PWD Building Schedule (2017) (3rd Corrigendum)Brick work with 1st class bricks in cement mortar (1:4)(b) In superstructure, ground floor 3 (Item No. 16, Page No. 016 of PWD Building Schedule (2017)125 mm. thick brick work with 1st class bricks in cement mortar (1:4) inground floor. IN GROUND FLOOR 4 (Page No. 66 ,Item No. 36 (I) (A) of PWD Building Schedule (2017) (3rd Corrigendum)Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive(6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxygrout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturersspecification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contrr]e)(I) With application slurry @1.75 kg/ Sq.m, 20 mm sandcement mortar (1:4) & 2 mm thick cement slurry at back sideof tiles, 0.2 kg/ Sq.m white cement for joint filling withpigment.B) Light ColourIN GROUND FLOOR 5 (Item No. 35 B(a)(i) & A (i), Page No.64 of PWD Building Schedule (2017)Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative 6 (Item No.- 5; Page No.- 116 of PWD Bldg. Schedule)Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge. 7 (Item No.- 16; Page No.- 126 of PWD Bldg. Schedule)Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge. 8 (Item No.- 5; Page No.- 116 of PWD Bldg. Schedule)Supplying, fitting and fixing Orissa pattern water closet in white glazedvitreous chinaware of approved make in position complete excluding P orS trap (excluding cost of concrete for fixing)(i) 580 mm X 440 mm 9 (Page No. 66,Item No. 14 ,(A)(iii) of PWD Sanitation & Plumbing (2017)Supplying,fitting and fixing cast iron P or S trap conformimg to I.S.3989/ 2009 and 1729/ 2002 including lead caulked joints and painting twocoats to the exposed surface. (Painting to be paid seperately). (A) P Trap(iii) 100 mm 10 (Page No. 189, Item No. II(b),of PWD Building Schedule (2017) (3rd Corrigendum)Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar(a) 20 mm thick plasterIN GROUND FLOOR 11 (b) 15 mm thick plaster 12 (Page No. 198 ,Item No. 5of PWD Building Schedule (2017)Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)IN GROUND FLOOR 13 (Page No. 195 ,Item No. 7of PWD Building Schedule (2017)Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. (In Ground Floor)(b) Two Coatsii) Solvent based interior grade Acrylic Primer 14 (Page No. 194 ,Item No. 1(b)of PWD Building Schedule (2017)White washing including cleaning and smoothening surface thoroughly. (iii) Two coats.(b) Two coats (to be done on specific instruction)IN GROUND FLOOR 15 (Page No. 197 ,Item No. 17(c) (i) of PWD Building Schedule (2017)Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground floor (Two Coat)c) Super Protective 100% Acrylic Emulsion 16 (Page No. 104 ,Item No. 13 (a) (ii) of PWD Building Schedule (2017)(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. IN GROUND FLOOR 17 (Page No. 114 ,Item No. 1 (d) of PWD Building Schedule (2017)Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(d) Sal : LocalIN GROUND FLOOR 18 (Page No. 198 ,Item No. 5of PWD Building Schedule (2017)Panel shutters of door and window, as per design (each panel consisting of singleplank without joint), including fitting and fixing the same in position butexcluding the cost of hinge and other fittings.In ground floor.(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm.(a) Ordinary Teak WoodIN GROUND FLOOR 19 (Item No. 1(b), Page No. 200 of PWD Building Schedule (2017)Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.IN GROUND FLOOR 20 ( Page No. 200 ,Item No. 1(a) of PWD Building Schedule (2017)(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.IN GROUND FLOOR 21 (Page No. 200,Item No. 2(A)IV,of PWD Building Schedule (2017)Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :(iv) Two coats (with any shade except white)IN GROUND FLOOR 22 (Page No. 201 Item No. 3B(b) of PWD Building Schedule (2017)Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface :(iv) Two coats (with any shade except white)IN GROUND FLOOR 23 (Page No. 165 ,Item No. 36 (I) (B) of PWD Building Schedule (2017) (3rd Corrigendum)M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceilingwith G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The boards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction ofEngineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete) 24 (Page No. 235 No. 1 (II)(A)(l) of PWD Building Schedule (2017)Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work).I) Natural whitea) 2- track sliding window 25 ii) Top frameSide frame 26 (Page No. 235 No. 1(A)(II)(d)of PWD Building Schedule (2017)Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISIembossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work).d) Shutter for all track sliding windowI) Natural whitei) Bottom & Top member 27 ii) Style side member 28 iii) Interlock member. 29 (Page No. 243 No. 9 (of PWD Building Schedule (2017)Supplying bubble free float glass of approved make and brandconforming to IS: 2835-1987. 30 (Page No. 242,Item No. 8 (i)(a) of PWD Building Schedule (2017)Supplying EPDM gusket of approved make and brand as per direction ofEngineer in charge.i) For sliding windows a) T shaped EPDM gasket for frames. 31 (Page No. 239 , Item No. 2,of PWD Building Schedule (2017)Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-i ) 2 track sliding window. 32 (Page No. 242,Item No. 7of PWD Building Schedule (2017)Supplying maruti lock (100mm) 33 (Page No. 242,Item No. 7of PWD S & P (2017)Supplying, fitting and fixing PVC pipes of approved make of Schedule 80(medium duty) conforming to ASTMD - 1785 and threaded to match withGI Pipes as per IS : 1239 (Part - I). with all necessary accessories,specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew,reducing socket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, making threads,fitting, fixing etc.complete in all respect including cost of all necessary fittings asrequired,jointing materials and two coats of painting with approved paintin any position above ground. (Payment will be made on the centre linemeasurements of total pipe line including all specials. No separatepayment will be made for accesories, specials. Payment for painting willbe made seperately)(a) For Exposed Work PVC Pipes25 mm 34 20 mm 35 15 mm 36 P-6,It-7 (e):-SECTION (A) - PLUMBING WORKS:-PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 mmBib cock 37 Stop cock 38 Suplying and Installation of Alloy Steel Study Chair With Cushion & Writing PadDimension 20D x 10W x 10Hcentimeter (Payment will made as per quotation) 39 Centrifugal Water Pump(1.5 HP)(Payment will made as boucher 40 Supply Fitting Fixing CC TV 8 Chennel (Payment will made as per quotation) 41 Monitor Set (Payment will made as per quotation) 42 Broadband installation (Payment will made as per quotation) 43 Add Electrification work 44 Add:- GST @ 18% 45 Add:- Cess @ 1%
