Tender For Peripheral Masonry Work Of Block 106 And Associated Areas At Inrpc, Nrb, Barc, Tarapur
Tender Value
1.70 Crore
Estimated cost
Bid Submission
09 Jun 2025
0 days left
EMD
3.40 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tarapur → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Peripheral Masonry Work Of Block 106 And Associated Areas At Inrpc, Nrb, Barc, Tarapur
BOQ
| Sl. No. | Item Description |
| 1 | Providing and laying in position cement concrete (RCC or PCC) of 1:1.5:3 at all levels (1 cement, 1.5 crushed sand, 3 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specifications and drawings but excluding the cost of shuttering, centering and steel reinforcement. |
| 2 | Providing and Laying Solid cement concrete block masonry with M-5 Grade of 190/ 140 mm thick in super structure in cement mortar 1:4 (using crushed sand). The rate shall also include scaffolding/staging, drilling of holes (if any) for fixing of rebar by applying chemical or welding or as directed by EIC, Making the cut out opening in masonary for flush concealing DB/plug point/switch boxenclosureincluding dismantling in floor or walls by cutting masonary and making good the damage to walls, painting, etc. existing surface and disposal of rubbish to the nearest dumping ground at a minimum distance of 50m away from the building. Note:( Reinforcement will be paid under relevant item) |
| 3 | Providing, centering, shuttering Form work using steel plates, timber planks for all types of structures including necessary strutting, proping, staging, supports, bracings etc. and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels for superstructure |
| 4 | Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Upto and including 32mm dia reinforcement: Using TMT bars of specified grades. TMT bars to be using virgin materials |
| 5 | Structural Steel Works of MS rolled single / built-up sections conforming to IS 2062 for staircase, edge angles, nosing angles in trench covers, gratings etc., mild steel embedment part for lining supports, sampling blisters, embedded cubicles, SBT line supports, trolleys, MSM EPs, RSW EPs, Electrical Plug EPs, PE door EPs, crane & monorail related EPs, trench pipe supports, various pipe EPs and plate EPs, ACVE related EPs such as duct EP, angle or channel frames for filter banks and closing ducts, supporting arrangement for EPs embedded in concrete, column guards, monorails, railings, handrails, ladders, box column sections, Monorail, built-up sections, crane girders, MS grid work for lining works, crane girders, trolley rails, joists, channels, in M.S Plain Plates and chequered Plates in Trench Covers, gratings, connection plates, supporting arrangement for EPs embedded in concrete etc., including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer in charge |
| 6 | Providing 20 mm thick plastering using Ready mix external plastering compound for external faces of brickwork / concrete surfaces including addition of water proofing agent, preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary,including Providing and fixing G.I. chicken mesh in the junctions of concrete & brick work / masonry (including cutting, fixing with nails in position before plastering) and as directed by the Engineer-in-charge |
| 7 | Extra for Plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof |
| 8 | Providing U3 finish for RCC Surfaces rendering smooth top of the suspended floors ,landings and staircases (treads and risers), walls, slab soffits etc. including grinding / carborandum stone for repairing surface defects in areas where forms are removed, ridges at form joints, honey-combed areas, damage resulting from the stripping of forms and bolt holes including chipping / tooling of bulges and ridges, rubbing, cleaning, necessary scaffolding / staging etc. with C.M 1:2 (using Crushed sand) including a floating coat of neat cement and protecting the surface subsequent to cleaning all as per specifications and as directed by the Engineer-in-charge at all levels |
| 9 | Providing and fixing of Hollow metal Two Hour fire rated doors (single/ double) consisting of door frame and shutters and all hardware fittings as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specifications. The recommended fire doors shall have type test report from CBRI or ARAI or NABL for minimum rating of 2 hours with vision panel. Deviation in specification and sheet thickness other than what is mentioned in the test certificates shall not be allowed. Proper label confirming the type of door and the hourly rating shall be mandatory. Door shall include fixing 4 nos heavy duty stainless steel 304 grade ball bearing, fire tested stainless steel butt hinges of size 100 x 75 x 3.00 mm (heavy weight) of approved make with suitable stainless steel screws, mortise / dead lock of approved make, a pair of 200 mm long stainless steel handles, 250 mm long stainless steel tower bolt / concealed tower bolt etc. frame hollow portion filled with PCC 1:2:4, necessary hold fast embedded in concrete, fixing in concrete with anchor fasteners. finished with Polyurethane painting of approved colour complete all as per drawings and specifications and as directed by the Engineer-in-charge |
| 10 | Providing and fixing fire rated Steel Rim Panic Exit Device of approved brand & quality in single leaf door upto 1000mm wide including all accessories etc. complete. |
| 11 | Supplying and fixing Rolling shutters of approved make as per ISI standards made out of required size of MS lathes 18 gauge interlocked together throughout entire length and jointed together at the end by end locks mounted on specially designed pipes shaft with brackets, side guides and arrangements for inside & outside locking with push and pull operation complete including the cost of providing and fixing necessary springs of required size and M. S top cover of required thickness for rolling shutters |
| 12 | Extra over the cost of rolling shutters for providing and fixing motorized arrangements( with remote & manual operation) including designing, control panels, limit switches, required wiring and cables from panel to motor and required size of shaft etc of approved make all as per standard specifications including commissioning and testing complete as directed by the Engineer-in-charge.(only power supply point will be provided) |
| 13 | Providing and fixing cast iron grating for rain water down takes at roof including chipping and grouting complete all as directed by the Engineer-in-charge |
| 14 | 150 mm x 150 mm |
| 15 | 200 mm x 200mm |
| 16 | 300 mm x 300mm |
| 17 | Supply and Installation of pregalvanised GI sheet steel enclosure fabricated out of 1.6 mm thick, suitable for concealed installation inMasonry wall, all sides knockout holes, two no\"s 10 mm nut holes for earthing, fabrication with grinding and arc spot welding,required number of knock out holes, etc. suitable for following Incomer and Outgoing feeders as per drawing, specifications & as per relevant IS, SLD, Technical specification & as per instructions of Engineer-in-charge. |
| 18 | Incomer- 1 No 4P MCB & Outgoing- 4 nos TPN MCB DB with RCBO |
| 19 | Supply |
| 20 | Installation |
| 21 | Incomer- 1 No 4P MCB & Outgoing- 6 nos TPN MCB DB with RCBO |
| 22 | Supply |
| 23 | Installation |
| 24 | Supply and Installation of pre-galvanizedGI sheet steel enclosure fabricated out of 1.6 mm thick, suitable for concealed installation inMasonry wall, all sides knockout holes, two no\"s 10 mm nut holes for earthing, fabrication with grinding and arc spot welding, with required number of knock out holes, etc. suitable for followingSingle phase Industrial/Decorative Socket along with MCB/piano switch for each socket as per drawing, specifications & as per relevant IS, SLD, Technical specification & as per instructions of Engineer-in-charge. |
| 25 | 1 no of 10A and 1 no of 20A, Single phase Industrial Socket along with Industrial type MCB for each Socket. |
| 26 | Supply |
| 27 | Installation |
| 28 | 1 no of 10A and 1 no of 20A, Single phase Modular Decorative Type Socket with domestic switch(MOC:Polycarbonate) Switch for each Socket. |
| 29 | Supply |
| 30 | Installation |
| 31 | Supply and Installation of pre-galvanized GI sheet steel enclosure fabricated out of 1.6 mm thick, suitable for concealed installation inMasonry wall, all sides knockout holes, two no\"s 10 mm nut holes for earthing, fabrication with grinding and arc spot welding, with required number of knock out holes, etc. suitable for followingSingle phase Industrial switches/MCB as per drawing, specifications & as per relevant IS, SLD, Technical specification & as per instructions of Engineer-in-charge. |
| 32 | 2 nos. of 10A, single pole MCB, 240 volts rated \"C\" curve of breaking capacity 10KA |
| 33 | Supply |
| 34 | Installation |
| 35 | Supply of 25 mm heavy duty 16 SWGrigid GI ERW conduit pipe along with all accessories such as junction box-1 way, 2 way,3 way,4 way with min 75 mm depth,heavy duty saddle, clamps, check nut, etc. |
| 36 | Embedment of 25mm rigid GI ERW conduit pipe making threads, removing burrs, connection of accessories, drawing of GI fish wire, cleating with heavy duty GI saddle or suit to site clamps on masonary wall, making chase in masonary wall, repairing the chase with PCC, cleaning and disposing the rubble as required under the instruction of Engineer in charge. |
| 37 | Supply of 14 SWG tinned solid copper conductor. |
| 38 | Laying of 14 SWG tinned solid copper conductor throughout along the conduit including fixing with ties, brazing etc as required. |
| 39 | Supply and embedment of copper earth plate/ pad of size 40mm wide x 6mm thick x 550 mm long having 10nos. Of 10mm dia tapped hole for outgoing connections and 11mm dia rod on back side for brazing of 2nos. 95 Sq.mm copper conductor including brazing, connection with suitable hardwares etc. as required |
| 40 | Supply of 95 Sq.mm ETP grade tinned, stranded bare copper earthing conductor |
| 41 | Concealed/ Surface Installation of 95Sq.mm ETP grade tinned stranded bare copper earthing conductor in brick wall along with making of chasing, finishing of wall. |
| 42 | Supply and Installation of 2-way pre-galvanized enclosure box for telephone point of size 75mm x 75mm x 45mm |
| 43 | Supply of required material and making of exothermic braze joints of copper conductor with other conductor or copper earthing pad including removal of burrs and debris as per technical specification and instruction of engineer in charge. |
AI Tender Summary
Tender Timeline
May 24, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedJun 09, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 11, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender