Tender For Annual Stage Contract For Maintenance, Repair And Renovation Of Dc Office Complex Within The Amar Niwas Premises At Tankipor, Srinagar-Jammu And Kashmir

TDR : 49243880

Tender Notice
BOQ

Expired

Srinagar , Jammu And Kashmir

Tender Brief : Tender For Annual Stage Contract For Maintenance, Repair And Renovation Of Dc Office Complex Within The Amar Niwas Premises At Tankipor

Document Fees
₹ 200 /-

EMD
₹ 2000.0 /-

Tender Value
₹ 1 Lakhs /-

Submission Date
26-05-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Supply of labours.
2	Mazdoor.
3	Carpenter 1st class.
4	Carpenter 2nd class
5	Mason 1st class.
6	Mason 2nd class.
7	Plumber.
8	Black Smith.
9	Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil : 1 meter from cutting edge
10	Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :
11	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.
12	Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.
13	Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.
14	Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive.
15	Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.
16	Providing & laying of stone soling hand packed in foundation and plinth incl ramming, watering, compaction & lead lifts all carriages upto site of work complete.
17	Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:
18	1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)
19	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
20	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size)
21	1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
22	1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)
23	1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
24	1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
25	Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with.
26	1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)
27	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
28	1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
29	1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)
30	1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
31	1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size
32	Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete
33	Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete
34	Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level
35	1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
36	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
37	Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
38	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
39	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more.
40	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
41	Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded
42	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes
43	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to steel windows by welding
44	Centering and shuttering including strutting, propping etc. and removal of form for:
45	Foundations, footings, bases of columns etc. for mass concrete.
46	Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.
47	Suspended floors, roofs, landings, balconies and access platforms.
48	Shelves (cast-in-situ)
49	Lintel, beams, plinth beams, girders, bressumers and cantilevers.
50	Columns, pillars, piers, abutments, posts and struts.
51	Stairs (excluding landings) except spiral staircases.
52	Spiral staircases (including landings)
53	Arches, domes, vaults upto 6 m span
54	Edges of slabs and breaks in floors and walls
55	Under 20 cm wide
56	Above 20 cm wide
57	Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)
58	Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level
59	Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in
60	Cement mortar 1:3 ( 1 cement : 3 coarse sand)
61	Cement mortar 1:4 ( 1 cement : 4 coarse sand)
62	Extra for half Brick masonry in superstructure above plinth level upto floor V level.
63	Dry random rubble masonry with hard stone in foundation and plinth With bond stone. (Quarry)
64	Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels
65	Raj Nagar plain white marble/Udaipur green marble/zebra black marble (16mm)
66	(Area of slab upto 0.5 sqm)
67	(Area of slab over 0.5 sqm)
68	Granite of any colour or shade (18mm)
69	(Area of slab upto 0.5 sqm)
70	(Area of slab over 0.5 sqm)
71	Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
72	Marble Work
73	Granite Work
74	Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete
75	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood
76	Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position
77	Budloo / Fir wood
78	Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. completePopular Wood
79	Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading
80	Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately) including fixing 50x12 mm beading complete with First class kail wood.
81	Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.
82	25mm thick with 12.5 mm nominal size stone aggregate.
83	40mm thick with 20 mm nominal size stone aggregate.
84	50 mm thick with 20mm nominal size stone aggregate.
85	Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Light shade using white cemen
86	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
87	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete
88	Size of tile 600x600 mm
89	Size of tile 1000x1000 mm
90	Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
91	Size of tile 600x600 mm
92	Size of tile 1000x1000 mm
93	Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
94	Size of tile 600x600 mm
95	Size of tile 1000x1000 mm
96	Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete
97	Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalization or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanized with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bimetallic contacts all complete required to perform as per specification and drawing The item includes cost of all material &labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, fieldtests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.
98	Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required
99	0.63 mm thick with zinc coating not less than 275 gram/m2
100	0.50 mm thick with zinc coating not less than 275 gram/m2
101	Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.
102	0.63 mm thick with zinc coating not less than 275 gram/m2
103	0.50 mm thick with zinc coating not less than 275 gram/m2
104	Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I.limpet and bitumen washers complete.
105	1.60 mm thick with zinc coating not less than 350 gram/m2
106	1.25 mm thick with zinc coating not less than 350 gram/m2
107	1.00 mm thick with zinc coating not less than 275 gram/m2
108	Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete.
109	0.80 mm thick with zinc coating not less than 275 gram/m2
110	0.63 mm thick with zinc coating not less than 275 gram/m2
111	Providing and fixing UV stabilized fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts and nuts 8mm dia. G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS: 10192 and IS: 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.
112	2mm thick corrugated (2.5\" or 4.2\" or 6\") or step-down (2\" or 3\" or 6\") as specified.
113	2mm thick flat
114	Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
115	In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.
116	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
117	Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of frame work which is to be paid separately.
118	Changez Khani
119	Chaar Gul
120	Chaar Phool
121	Pahal Gardan
122	Dawaz-dal-i-girde
123	Paanch Murabah
124	12mm Cement plaster of mix
125	1 : 4 ( 1 cement : 4 fine sand)
126	1 : 6 ( 1 cement : 6 fine sand)
127	15mm Cement plaster on the rough side of single or half brick wall of mix
128	1 : 4 ( 1 cement : 4 fine sand)
129	1 : 6 ( 1 cement : 6 fine sand)
130	6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)
131	20mm Cement plaster of mix:
132	1 : 4 ( 1 cement : 4 fine sand)
133	1 : 6 ( 1 cement : 6 fine sand)
134	Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand)
135	Flush/Ruled Pointing
136	Raised and cut pointing
137	White washing with lime to give an even shade on New Work (three or more coats)
138	Colour washing such as green blue or buff to give an even shade
139	New work (two or more coats) with a basecoat of white washing with lime.
140	New work (two or more coats) with basecoat of whiting
141	Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work, over and including water thinnable priming coat to give an even shade
142	Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer
143	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre,two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer\"s specifications
144	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.
145	Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)
146	Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm
147	Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)
148	Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)
149	Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers\" specifications:
150	Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm
151	Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture
152	Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture
153	Applying priming coat:
154	With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)
155	With ready mixed aluminum primer of approved brand and manufacture on resinous wood and ply wood
156	With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works
157	With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel work (second coat)
158	Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces:
159	One coat
160	Two coats
161	Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc complete
162	On steel work
163	On concrete work
164	Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.
165	Applying a coat of mordant solution on G.S. sheets:
166	With a solution of 38gms of copper acetate in liter of soft water
167	With a solution made of 13gms of hydrochloric acid in a solution of 13gms each of copper chloride, copper nitrate and ammonium chloride dissolved in a liter of soft water.
168	Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture over and including a priming coat of ready mixed zinc chromate yellow primer on new work.
169	75 mm diameter pipe
170	100 mm diameter pipe
171	150 mm diameter pipe
172	Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with aluminum paint of approved brand and manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work.
173	75 mm diameter pipe
174	100 mm diameter pipe
175	150 mm diameter pipe
176	Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work :
177	100 mm diameter pipe
178	150 mm diameter pipe
179	Painting with oil type wood preservative of approved brand and manufacture on New work (two or more coats)
180	Providing and applying two coats of fire retardant paint on cleaned wood/ply surface @ 3.5sqm per liter per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant
181	Coal tarring two coats on new work using 0.16 liter and 0.12 liter coal tar per sqm in the 1st coat and 2nd coat respectively
182	Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work
183	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.
184	Two or more coats on new work
185	Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
186	Painting with aluminum paint of approved brand and manufacture to give an even shade. Two or more coats on new work
187	Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work
188	Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade on new work Two or more coats.
189	Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade on new work Two or more coats.
190	Varnishing with varnish of approved brand and manufacture:
191	Two or more coats of glue sizing with copal varnish over and under coat of flatting varnish.
192	Two or more coats of glue sizing with spar varnish on an under coat of flatting varnish
193	French spirit polishing, Two or more coats on new works including a coat of wood filler
194	Polishing on wood work with ready mixed wax polish of approved brand and manufacture on New work
195	Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture
196	Lettering with black Japan paint of approved brand and manufacture.
197	Washed stone grit plaster on exterior walls of height upto 10 m above ground level in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2kg of cement per m2, top layer 15mm cement plaster 1:1/2 :2 (1 cement: 1/2 coarse sand : 2 stone chippings 10mm nominal size), in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer-in -charge (payment for providing grooves shall be made separately).
198	Forming groove of uniform size in the top layer of washed stone gritplaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :
199	15 mm wide and 15 mm deep groove
200	20 mm wide and 15 mm deep groove
201	Extra for washed grit plaster on exterior walls of height more than 10m ground level for every additional height of 3m or part thereof
202	Extra for washed stone grit plaster on circular work not exceeding 6m in radius (in two coats)
203	Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer in- Charge.
204	Extra for using white cement in place of ordinary cement in the top layer of the item of washed stone grit plaster
205	Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
206	1 mm thick
207	2 mm thick
208	Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.
209	One coat
210	Two coats
211	Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.
212	One coat
213	Two coats
214	Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.
215	One coat
216	Two coats
217	Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.
218	With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter
219	With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter
220	With water thinnable cement primer on wall surface having VOC content less than 50 grams/liter
221	Finishing walls with 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm.
222	Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
223	Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade.
224	Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
225	Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.
226	Painting with aluminum paint of approved brand and manufacture to give an even shade, one or more coats on old work.
227	Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.
228	Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade, one or more coats on old work
229	French spirit polishing, one or more coats on old work
230	Polishing on wood work with readymade wax polish of approved brand and manufacture on old work.
231	Re-lettering with black Japan paint of approved brand and manufacture.
232	Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.
233	Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin :
234	32 mm dia.
235	40 mm dia.
236	Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work
237	Finishing walls with water proofing cement paint of required shade:
238	Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat.
239	Old work (one or more coats applied @ 2.20 kg/10sqm) complete
240	Finishing walls with textured exterior paint of required shade:
241	Old work (two or more coats on existing cement paint surface applied @ 3.28 ltr/10sqm)
242	Old work (one or more coats) applied @1.82 ltr/10sqm
243	Finishing walls with Acrylic smooth exterior paint of required shade:
244	Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)
245	Old work (one or more coats applied @ 0.90 liters/ 10sqm)
246	Finishing walls with premium Acrylic smooth exterior paint with silicon additives of required shade:
247	Old work (Two or more coats applied @ 1.43 liters/ 10 sqm) over existing cement paint surface.
248	Old work (one or more coats applied @ 0.83 liters/ 10sqm)
249	Varnishing with varnish of approved brand and manufacture:
250	One or more coats with copal varnish.
251	One or more coats with spar varnish.
252	Melamine polishing on wood work (one or more coats)
253	Varnishing with flatting varnish of approved brand and manufacture one or more coats on old work
254	Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead
255	With cement mortar 1:4 (1 cement : 4 fine sand)
256	With cement mortar 1:4 (1 cement : 4 coarse sand)
257	Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding holdfasts in cement concrete blocks of size 15x10x10cm with cement concrete 1:3:6 (1 cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead:
258	Door chowkhats
259	Window chowkhats
260	Clerestory window chowkhats
261	Fixing chowkhat in existing opening in brick/RCC wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhats and 2 nos. on each vertical member of window chowkhats), including cost of dash fasteners/chemical fasteners.
262	Making the opening for door/window/clerestory window in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground.
263	Renewing glass panes, with putty and nails wherever necessary including raking out old putty :
264	Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm)
265	Float glass panes of thickness 5.0 mm(weight not less than 12.5 kg/sqm)
266	Renewing glass panes, with wooden fillets wherever necessary :
267	Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)
268	Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)
269	Renewing glass panes and re-fixing existing wooden fillets:
270	Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)
271	Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)
272	Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.
273	Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
274	Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. (a) Internal Work- Exposed on wall
275	Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.
276	Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:
277	1:3:6 or richer mix (i/c equivalent design mix)
278	1:4:8 or leaner mix (i/c equivalent design mix)
279	Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar
280	Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) From brick work in cement mortar
281	.Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead
282	Of area of 3 sqm. and below
283	Of area beyond 3 sqm.
284	Dismantling steel work in single sections including dismembering and stacking within 50 meters lead inR.S. Joists
285	Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead.
286	Of sectional area 40 sqcm. and above.
287	Of sectional area below 40 sqcm.
288	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead.
289	For thickness of tiles 10 mm to 25 mm
290	Demolishing RCC work by mechanical means & stockpiling at designated locations & disposal of dismantled materials upto a lead of 1 kilometer, stacking serviceable & unserviceable material separately including cutting reinforcement bars
291	Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets
292	20 mm dia ( heavy type)
293	25 mm dia ( heavy type)
294	Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
295	Painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to IS: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.
296	New work (Two or more coats)
297	Old work ( One or more coats)
298	Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).
299	Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x 25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (The rate is excluding the cost of tiles which will be paid for separately).
300	GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.
301	Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing. One face dressed
302	Fine chisel dressed
303	Rough chisel dressed
304	Extra for fine chisel dressed Devri Stone in square or rectangular Pillars
305	Providing and laying rough chisel dressed Devri Stone in kerbs, of size 200x200 mm face with chamfer in cement mortar 1: 6 (1 cement : 6 coarse sand) including curing.
306	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). imported kail wood: (35mm Thick)
307	Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge (35mm Thick)
308	Providing and fixing wire gauze using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows including cost of beading complete.
309	Providing and fixing of chicken mesh wherever required of specified size including cost of beading and nails complete.
310	Providing and fixing 30-35 mm thick paneled door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws including paneling of 12mm thick laminated board both sides laminated as per the approved design complete with required beading/moldings. (styles and rails shall be of standard size) in fittings imported kail wood:
311	Providing and fixing 30-35 mm thick paneled door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws including cost of 25-30mm thick paneling of approved design with required beading/moldings. imported kail wood:
312	Providing and fixing 30-35 mm thick paneled/ flush door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws Readymade ornamental modular, factory manufactured machine made of hard wood teak finished, of approved quality, color and shade.
313	Providing and fixing 35 mm thick paneled door shutters with wood carved panels (Carving on one side) including polishing, and ISI marked black enameled M.S. butt hinges with necessary screws as per the approved designcomplete with required beading/moldings. (styles and rails shall be of standard size) imported kail wood:
314	Providing and fixing 32 mm thick paneled door shutters with wood carved panels (Carving on both sides) including polishing, and ISI marked black enameled M.S. butt hinges with necessary screws as per the approved designcomplete with required beading/moldings. (styles and rails shall be of standard size) imported kail wood:
315	Providing and fixing of wooden paneling/ lining of 12mm (net thickness) including providing and fixing of ground frame work (50x25mm or as specified) of first class Budloo wood/ 19mm ply including cost of screws, wooden plugs etc. complete as per directions of EIC
316	Made from imported wood
317	Made from Budloo wood
318	Providing and fixing of ply wood including cost of nails adhesive etc. complete at all places.
319	4 mm thick
320	6 mm thick
321	12 mm thick
322	19 mm thick
323	Providing and fixing of single side laminated ply wood including cost of nails adhesive etc. complete at all places.
324	6 mm thick
325	12 mm thick
326	18-19 mm thick
327	Providing and fixing of 19mm thick commercial block board at all places including cost of nails and adhesive complete. Thickness/ Pattern/ Design to be approved by EIC
328	Providing and fixing of Dulmica/ sun mica sheeting including cost of nails and adhesive complete.
329	0.8-1 mm thick for lining
330	0.4-0.5mm thick for lining
331	Providing and fixing wood work in fencing that is in planks of the following nominal size excluding cost of posts and runners. 1st class Budloo wood. (ornamental)
332	20 mm thick.
333	25 mm thick.
334	35 mm thick.
335	Providing and fixing of ornamental cornice of following size. 1st class budloo/imported wood.
336	40-50 mm
337	65 mm
338	75 mm
339	Providing and fixing of PVC edge beading
340	12 mm
341	19 mm
342	25 mm
343	Providing and fixing 20mm thick overlapped weather boarding in soffits of 1st class imported wood including applying priming coat of approved quality primer.
344	Providing and fixing of planed eaves boarding 250mm x 30mm size of 1st Class imported wood.
345	Providing and fixing of planed eaves boarding 250mm x 30mm size of 1st Class Budloo wood.
346	Providing and fixing of wooden beading ornamental 25mmx6mm size of Budloo wood.
347	Providing and fixing of reflective glass panes 3.5 mm thick in doors windows and clearstory windows including cost of budloo wood beading of required size.
348	Providing and fixing of Buj tile cladding of required pattern. Shade and design over 20mm thick cement plaster 1:3 mix (1 cement: 3coarse sand) including jointing with neat cement slurry complete.
349	Providing and fixing of Interlocking/Chequered precast cement concrete tiles colored(rubber finish) in foot paths & courtyards jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and cleaning etc. complete on 20mm thick layer of dry sand .
350	40mm thick.
351	50mm thick.
352	75mm thick.
353	Providing and fixing A.C.P 3mm multi coloured (Fire retardant) in partitions, ceilings, shutters frames etc in panels of min size 600mm x 600mmincluding cost of rubber,neoprene gasket ,waterproof silicon sealent , or as required at site as per the directions of concerned engineer in charge.complete job
354	Providing and laying G.S.B. grade including compacting, ramming, watering and carriage complete. (Hand ramming in plinth or rooms)
355	Engagement of tipper including fuel charges complete.
356	Engagement of excavator (JCB) in all terrains including fuel charges complete.
357	Engagement of hand cart all complete
358	Providing and fixing of wardrobe, almirah, drawer locks(Sample to be approved by EIC)
359	Providing and fixing of aluminum double channel with wheel set for sliding glass window of approved quality of following sizes.
360	20 mm
361	25 mm
362	Providing and fixing of door closer capsule type of standard make
363	Providing and fixing of door closer springtype of standard make
364	Providing and fixing of following fittings
365	Aldrop
366	Tower Bolt 100mm
367	Tower Bolt 150mm
368	Handle 100mm
369	Handle 150mm
370	I Hook
371	Hinges 75mm
372	Hinges 100mm
373	Lockable sliding Aldrop 250-300mm long (Godrej/ Link/Ramson or equivalent)
374	Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply board in sides, shelves and wherever required including 6mm ply wood on back and 19MM ply boardin shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including (painting two or more coats of synthetic enamel paint of approved quality and color inside) including cost of following aluminum fittings and locks of approved make. 15mm dia. M.S. pipe chromium plated with necessary brackets 4\"-0\" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured).
375	50-60 cm deep
376	40-45 cm deep
377	20-30 cm deep
378	extra for using ply to ply instead of board (Face measurement)
379	extra for using lining instead of painting on internal surface as per measurement - 12mm
380	Extra for using 10-12mm ply instead of 6mm on back side of Wardrobe/ Kitchen cabinets
381	Extra for using MDF shuttes ornamental type of required thickness instead of ply/ pine shutters (Face measurement)
382	Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.
383	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.
384	Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C automatic flushing cistern, with fittings, standard size G.I./ PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and in C.P brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required:Range of three squatting plates with 10 liter P.V.C. automatic flushing cistern.
385	Providing and fixing wash basinwith CI/MS/ brackets including painting of fittings and brackets, cutting and making good walls wherever required white vitreous china wash basin size 630x450mm with32mm dia. C.P. brass union & flexible waste pipe(Jaquar/ Hindware/ Cera/ Kerrovit or equivalent)
386	Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
387	Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231,with fittings and fixtures complete. 10 liters capacity- white(Sample to be approved by EIC)
388	Providing and fixing solid plastic seat with lid for pedestal type W.C. pancomplete.(Sample to be approved by EIC)
389	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm size respectively.
390	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x460mm bowl depth 200mm
391	Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings Size 600x450x200 mm.
392	Providing and fixing of white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm respectively with automatic flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 liter white PVC automatic flushing cistern(Sample to be approved by EIC)
393	Providing and fixing of C.P grating 100mm size. ISI
394	Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings and clamps including cutting and making good the walls etc. internal work (Exposed on Walls)(Sample to be approved by EIC)
395	15mm dia. Nominal bore
396	20mm dia. Nominal bore
397	25mm dia. Nominal bore
398	32mm dia. Nominal bore
399	40mm dia. Nominal bore
400	50mm dia. Nominal bore
401	Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings excluding trenching and refilling etc. (external work)(Sample to be approved by EIC)
402	15mm dia. Nominal bore
403	20mm dia. Nominal bore
404	25mm dia. Nominal bore
405	32mm dia. Nominal bore
406	40mm dia. Nominal bore
407	50mm dia. Nominal bore
408	65mm dia. Nominal bore
409	80mm dia. Nominal bore
410	100mm dia. Nominal bore
411	Providing and fixing of following G.I. fittings. 15 mm nominal bore.(Sample to be approved by EIC)
412	Elbow
413	Tee
414	Union
415	pvc plug/ G.I Plug
416	Nipple
417	50mm long.
418	75mm long
419	100mm long
420	150mm long
421	Socket
422	15mm
423	20mm
424	25mm
425	Reducer
426	15mm-20mm
427	20mm-25mm
428	20mm-32mm
429	25mm-32mm
430	Providing and fixing of following G.I. fittings. 20 mm nominal bore.(Sample to be approved by EIC)
431	Elbow
432	Tee
433	Union
434	pvc plug/ G.I Plug
435	Nipple
436	50mm long.
437	75mm long
438	100mm long
439	150mm long
440	Providing and fixing of PVC connection with C.P. brass unions
441	300mm long.
442	450mm long
443	600mm long
444	Providing and fixing ball valve (brass) of approved quality complete (Sample to be approved by EIC)
445	15mm dia.
446	20mm dia.
447	25mm dia.
448	40mm dia.
449	Providing and fixing gate valve (brass) of approved quality complete (Sample to be approved by EIC)
450	15mm dia.
451	20mm dia.
452	25mm dia.
453	40mm dia.
454	50mm dia.
455	Providing and fixing of Ball cock of approved quality and make with plastic float. (PVC type)
456	15 mm
457	20 mm
458	Providing and fixing of flexible PVC Pipe
459	For Washbasin
460	For Urinal
461	Providing and fixing of Ball cock of approved quality and make without plastic float.
462	15 mm
463	20 mm
464	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
465	Construction of plateform for W.C. with brick masonry in cement mortar 1:6 mix. Including filling of sand and providing of 15mm cement plaster in 1:4 mix. Complete job of size as directed at site
466	Providing and fixing of C.P. Cups for C.P. fittings.
467	Providing and fixing of C.I. manhole cover heavy duty of following sizes.
468	12\"x12\"
469	18\"x18\"
470	24\"X24\"
471	Providing , installation, commissioning and testing Hot water Geyzer of approved make including fixing with bolts/ fasteners/PVC connection etc. Venus, Recold, Hindware, Havells, Jaquar, Crompton of required capacity fittings and fixtures all complete wherever required in the course of completion. complete job.
472	50 Litre
473	35 Litre
474	25 Litre
475	Providing and fixing of PVC connection for wash basins, geysers etc.
476	30-45 cm in length
477	60-90 cm in length
478	Providing and fixing Geyser elements (as per Geyser type) dry/ wet
479	Providing and fixing Geyser thermostat
480	Providing and fixing Drain plug with washer.
481	Providing and fixing Safety valve for geysers.
482	Providing and fixing water washers for geysers.
483	Providing and fixing of auto thermo cut for geyser.
484	Providing and fixing of pressure water ball Valve
485	Providing and fixing C.P. brass bib cock of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 15mm nominal bore with flange
486	Short Body
487	Long Body
488	Providing and fixing of 15mm size chromium plated cast brass pillar cock of approved quality(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)
489	Providing and fixing of 15mm size chromium plated cast brass angle valve of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with wall flange
490	Providing and fixing of 15mm size chromium plated cast brass wash basin mixer as menioned below (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)
491	Pillar Type 2 Knobs
492	Pillar Type Single Lever
493	Wall Mounted type
494	Providing and fixing of 15mm size chromium plated cast brass sink mixer Wall mounted/ Counter mounted of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)
495	Providing and fixing of hand shower with chain of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)
496	Providing and fixing of shower including shower arm of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange
497	Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonicof approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange
498	Providing and fixing of 15mm size chromium plated cast brass wall mixer with bend pipe for head showerof approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange
499	Providing and fixing Towel ring 30mm. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)withflange
500	Providing and fixing Towel rod (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 600mm long

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Jammu And Kashmir Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Annual Stage Contract For Maintenance, Repair And Renovation Of Dc Office Complex Within The Amar Niwas Premises At Tankipor, Srinagar-Jammu And Kashmir

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Annual Stage Contract For Maintenance, Repair And Renovation Of Dc Office Complex Within The Amar Niwas Premises At Tankipor, Srinagar-Jammu And Kashmir

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us