Tender For Construction Of Boundary Wall, Store shed And Guardhut At 220 Kv Gss Bayana; 1 B-1/1.8Earth work in excavation by mechanical means Hydraulic excavator/manual means in found trenches or drains not exceeding 1.5 M in width or 10 Sqm on plan including dressing of sides and ramming of bottom lift upto 1.5 Mtr including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 Mtr all kind of soils. 2 B-3/3.1.6P&L in position Cement Concrete incl. Curing compaction etc. of specified Grade Excl.the cost of Centering & Shuttering all works up to Plinth level1:4:8 (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) 3 B-6/6.1.6Random Rubble stone masonry with hard stone in Foundation and plinth in Cement Sand Mortar 1:6 (1 cement:6 sand) above 30 CM thick walls. 4 B-5/5.2.2Brick work with F.P.S brick of class designation 75 in Super Structure above Plinth Level up to floor V level In all shapes and size in CM 1:6 ( 1 cement : 6 coarse sand) 5 B-5/5.8.3 Half brick masonry Super Structure above Plinth Level up to floor V level using bricks of designation 75 in CM 1:6( 1 cement : 6 sand ). 6 B-5/5.3.1Add extra for Square of rectangular pillars in superstructure brick work up to five story upto 45 cm length and all sides are free 7 B-8/(8.13.2.1 + 8.14)Providing &Fixing External Grade board solid core single leaf flush door shutters IS 2202-67 marked using Phenol formal dehydreresin in glue both sides with approved steel fittings complete as per Annexure A 30mm thick commercial veneer both side including providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured). Extra for providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13. 8 B-4/4.1Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix 9 B-4/4.2Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement, 3 coarse sand) and making good the joints and cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and strut etc. M20 grade Nominal Mix / Design Mix 10 B-4/4.3 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 11 (B-4/4.13.3) Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (Original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo Mechanically treated bars bars (IS : 1139). 12 B-4/4.9Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc. 13 B-4/4.10.2Centring & Shutteringwith plywood or steel sheets including strutting propping bracing both ways with steel props and removal of formwork for up to floor fivelevel for: Suspended floor, roofs, landings, staircases, balconies girders, cantilevers, bands, coping bed plates, anchor blocks, sills,chajjas, lintel beams, plinth beam etc. 14 B-4/4.10.3Centring & Shuttering with plywood or steel sheets including strutting propping bracing both ways with steel props and removal of formwork for up to floor fivelevel for: Columns, pillars, posts and struts etc. 15 B-6/6.17.3Supplying &Fixing machine cut and polished stone shelves tands and sills in CM 1:3 with machine cut edges Kota stone minimum 30 mm thick 16 B-11/11.19.2 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing completeFor area of each slab from2001 to 5000 Sqcm 17 B-11/11.18.12 Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) For area of each slab from 2001 to 5000 sqcm 18 B-9/9.19.3+9.25Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of pin headed glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :Windows side hung /Ventilators top or centre hung (openable) 19 B-9/9.26 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 20 B-9/9.27Providing and fixing Square bars or other flat welded to window, ventilatiors etc. 21 B-9/9.20Providing brass handles/peg stays and fittings in place of oxidized fitting 22 B-10/10.20P/F 20mm thick precast terrazo tiles of appd make with marble chips of size upto 6mm laid over roof with neat cement slurry mixed with pigment to match the shade of the tiles, incl cutting grinding rubbimg with m/c complete on 20mm thick bed of cement sand mortar 1:4 23 B-3/3.2.3 Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.M15 grade Nominal Mix 1:2:4(1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). 24 B-10/10.17.1Grading roof for water proofing treatment withwater proffing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 25 B-12/12.3.2Plaster on new surface on walls in Cement Sand Mortar 1:6 incl. Racking of joint etc. complete fine finished 20mm thick 26 B-12/12.3.3 Plaster on new surface on walls in Cement Sand Mortar 1:6 incl. Racking of joint etc. complete fine finished 12mm thick 27 B-12/12.5 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3-fine sand) 28 B-11/11.17.4Chequered precast cement concrete tiles 22mm thick in footpath and courtyardjointed with neat cement slurry mixed withpigment to match the shade of tiles including rubbing and cleaning etc complete on 20mm thickbed of C.M. 1:4(1 cement: 4 coarse sand) ordinary cement without any pigment 29 B-10/10.22Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 30 B-9/9.13Supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade No. 2 and M.S. top cover 1.25mm thick for rolling shutters as per design & IS 6248- 1979. (Clear openable area to be measured for payment). 31 B-9/9.1 Structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height upto 10 m), fixing in position and applying a priming coat of approved steel primer all complete. 32 B-9/9.2Structural steel work riveted, bolted orwelded in built up sections, trusses and framed work , including cutting, hoisting (height up to 10 m), fixing In position and applying a priming coat of approved steel primer all complete: 33 (B-9/9.8.1) Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide Extra if square,rectangular hollow tubelarsections are used or grill made by flats only 34 B-9/9.5P&F T-iron frames for doors windows and ventilators of mild steel Tee section joints mitered and welded with 15x3mm long 10 CM long embedded in CC block 15x10x10 CM of 1:3:6 (1 cement : 3 core sand: 6 stone agrregate 20 MM nominal size) or with wooden plugs and screw or rawl plug and screws or with fixing clips or with bolts and nuts as reqd,. incl. Fixing of nece. Butt hinges and screw and applying priming coat of appd. Steel primer. 35 B-9/9.33+9.35 P&F galvanized barbed wire. 36 B-8/8.23.1 Providing and fixing Nigeria/ ghana / Ivory coast teak wood grade first mouldings and beading in doors and windows size 50x12mm 37 B-12/12.46.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work 38 B-12/12.34.1 White washing with lime to give an even shade including all scaffolding:new work ( three or more coats) 39 B-12/12.35.1 Colour washing of all shades to give an even shade including all scaffolding : New work (two or more coats) with a base coat of white washing with lime. 40 B-12/12.42Finishing walls with Acrylic smooth exterior paint of required shade including all scaffolding New work(Twoor more coat applied @ 1.67ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10sqm) 41 B-3/3.8P&F precast CC coping 1:2:4 mix 50mm thick complete as per specification 42 S-1/1.2.2P & F Indian type white glazed vitreous China Ist quality W.C Orissa Pan IS 2556 mark with 100mm vitreous China P or S trap incl. Cutting and making good the wall and floor size 580 x 440 mm 43 S-1/1.36.3P&FWVC wash basin Ist quality IS 2556 mark of appd,. Make with CI brackets duly painted 1 No. 15mm C.P. pillar cock IS 8934 mark & 32mm C.P. brass waste coupling of appd,. Make 25mm G.I. waste pipe complete incl. Cutting and making good the wall size 550x400mm 44 S-1/1.45.1P&F looking mirrors with PVC frame of appd. Quality Atul or equivalent size 500x400mm 45 S-1/1.47.8 P&F towel rail or ring of appd. Quality /make C.P. Brass Towel Ring revolving type 46 S-2/2.1.1B P & F G.I. pipes (Internal Work) with G.I. Fittings (IS 1239-1992 mark) and MS clamp including cutting and making good the walls and floors: Exposed on wall 15 mm dia nominal boreB Class 47 S-2/2.1.9 B P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors:Concealed pipe in wall including painting with anticorrosive bitumen paint 15 mm nominal dia. Class B 48 S-2/2.1.3B P & F G.I. pipes (Internal Work) with G.I. Fittings (IS 1239-1992 mark) and MS clamp including cutting and making good the walls and floors: Exposed on wall 25 mm dia nominal boreB Class 49 S-2/2.2.3 P&F G.I. pipes (external work) with G.I. fittings (IS:1239 - 1292 Mark) including unionIS 1239 mark & MS clamps incl. Cutting and making good the wall and floor B Class 25mm dia 50 S-2/2.3.1 Making connection of G.I. distribution branch with G.I. main including all fitting. Upto 25mm dia 51 S-2/2.7.1P&F bib cock IS 8931 mark superior quality of appd. Make Brass bib cock 15mmdia 400 Gms. 52 S-2/2.7.4 P&F bib cock IS 8931 mark superior quality of appd. MakeC.P. brass long body 15mm dia Weight not less than 690 Gram 53 S-2/2.8.5P&F stop cock IS 8931 mark superior quality & of approved makeC.P. brass concealed stop cock 15mm 54 S-3/3.44.2Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia 55 S-3/3.45.4Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia bend 87.5 Dg 56 S-3/3.45.17Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia Single Tee with Door 57 S-3 /3.45.30Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaVent Cowel 100mm 58 S-3/3.45.6 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia Door bend 87.5 Dg. 59 S-3/3.45.5Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm dia Door bend 45 Dg 60 S-3/3.45.12Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaPipe Clip 61 S-3/3.45.26Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110mm diaNahni Trap without Jali 4 62 S-3/3.16.3P&F rigid PVC pipe (IS 4985 mark) class IInd /4 Kg P.SqCM ) approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant 110mm dia 63 S-2/2.26.3P&F PVC storage tank IS 12701 marked indicating the BIS license No. of approved make with cover 25mm dia 1 M long GI over flow pipe & 25 CM long wash out pipe with plug & socket incl. Making conn. Etc. complete of appd. Design500 Ltr capacity 64 S-2/2.15.1P&F full way valve IS 778 mark or wheel valve of approvedMake gun metal 15mm Nominal Bore 65 S-2/2.15.3P&F full way valve IS 778 mark or wheel valve of approvedMake gun metal 25mm Nominal Bore 66 S-2/2.13.2P & F 15 mm. Dia Connection Pipe of approved quality/make : PVC pipe withC.P. Brass nuts upto length, 370mm 67 S-2/2.11.1 P&F ball cock IS 1703 mark with rod& PVC ball complete brass Weight400 Gram 15mm dia 68 S-3/3.3.2Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) upto haunches of S.W. pipes including 150 mm thick bed concrete (Width W= Dia of pipe in Cm+ 30Cm.) concrete width to be reduced from width W at center of pipe to `0` at top of pipe.(Excluding cost of pipe) 150mm dia S.W pipe 69 S-3/3.19.1 Construction of manhole in all type of soil inner size 90x60 CM 450mm thick masonry in CM 1:6 10 CM thick CC 1:5 :10in foundation 20mm thick inside plaster in CM 1:6 finished with floating neat cement 50mm thick M-15 Gr CC flooring making channels 80mm thick stone slab covering with 40mm thick M-15 Gr CC flooring RCC cover with frame of 450mm dia E/W etc. complete as per design incl. Disposal of surplus earth within 50 Mtr Depth upto 0.50mtr. 70 S-3/3.21.1Construction of chamber in all types of soil with 300 mm thick masonry in CM 1.5 M 100mm thick CC 1:5:10 in foundation 20mm thick insider plaster in CM 1:6 finished with floating neat cement 50mm thick M-15 Gr CC flooring E/W etc. complete as per design including disposal of surplus earth within a lead of 50 Mtr inside size 300x300mm depth up to 0.5 M & size 300 x 300 mm RCC cover with frame. 71 S-3/ 3.22.1Construction of Soakage well in all type of soil 300 mm thick dry masonry ,top and bottom 300 mm course in CSM 1:6,80 mm thick stone slab, jointing of slab in CM 1:3.Ralthal,Kharanja,40 mm thick M-15 grade C.C. flooring, earth work complete as per approved including disposal of earth with in a lead 50 mtr. Size 300 Cm. dia. Outside & 300 Cm depth 72 (S-3/3.27.1) Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 gradeC.C floor &RCC slab covering with M15 grade c.c. floor,50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 200x100x130 cm.(for 10 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect 73 S-1/1.55.2P&F bath shower of approved quality / make C.P. brass of heavy and superior quality 150mm 74 S-2/2.14.7P&F flush cock/valve (IS 9758 mark) or wc of approved quality make cp brass half turn conclead 25 mm nominal bore 75 S-2/2.12.1 P&F inlet connection (Angle valves) superior quality of approved make for wash basin Gyser etc . C.P. inlet connection 15mm brass(IS 8931 marked) 76 S-1/1.54.1 P&F shower arm 15mm diaof approved quality make C.P. brass heavy & superior quality150mm projection 77 (S-1/1.38.9.2) P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :1.0 mm thick stainless steel AISI -304 & IS 13983-1994kitchen sink of approved make as per Engineer-in-chargewith large waste coupling.22 x 18 x 720x16x7 78 B-1/1.25 Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. 79 B-1/1.34 Supplying chemical emulsionin sealed containers including delivery as specified.Chlorpyriphos/Lindane emulsifiable concentrate of 20% 80 B-1/1.36Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion) 81 Construction of Embankment with aprroved matrerial abtained fromborrow pits with a lift upto 1.5 m . Transporting to side. Spreading , grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead as per technical specifExtra for watering the earth to bring the earth upto requiredO. M .C excluding rolling , field density not less than 95% of maximum dry density ( Ordinary proctor test) lead upto 05 km (R-3/19.1+(R-1/1.1.9)+R-3/11.1+R-3/9-R-1/1.1.4) 82 R-8/8.12:- Supply of Retro-reflective sign boards size 1800x1200 mm made out of 2 mm thick aluminium sheet duly frame with 40mm M.S. Black tube ( Medium Class) as per IS -1239 (Part-I) 1979 with Inner support to M.S. flat 12x3 mm whole structure is fixed with two supports each side 75 mm long and 40 mm M.S. black tube on two posts of 60mm dia M.S. Black tube (Medium class) as per 1239(Part-I) 1979 2.03 metre long each and also provision of hold fass of M.S. bars 12 mm and 25 cm long two on each post. The sheet has to be stove enameled or epoxy painting one side and other side retro-reflective high itensity and black non reflective letter in non reflective sheet. The sandard letters and numbrals have to be made as per IRC 30-1968 and the board shall be conformed to the Morth specifications clause. 801 Post and outer frame of board to be painted with black and white strips of synthetic enamel paint with black and white strips. 83 R-11/11.5.1 :- Providing & fixing letters/boarders from reflective tape of approved quality in standard width of MORTH specifications clause 800. providing and fixing letters (100mm wide) 84 E-01/1.1.1 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR:short point (upto 3.0 m) 85 E-01/1.1.2 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR:Medium point (upto 6.0 m) 86 E-01/1.1.3 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR:Long point (upto 10.0 m) 87 E-01/1.3.1Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR:on board 88 (E-4/4.1.2)Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 2 x 1.5 sq.mm 89 (E-4/4.1.1)Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 1 x 1.5 sq.mm 90 (E-4/4.1.6)Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR2 x 2.5 sq.mm 91 (E-4/4.1.11)Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR2 x 4 sq.mm 92 E-01/1.4.1 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along withISI marked (IS:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR:20mm 93 (E-7/7.37)Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification ofWiring accessories refer ChapterE - 07related item & For additional technical parameters of product / work refer Annexure A attached with this BSR 94 (E-7/7.24) Providing & Fixing of ISI marked surface type buzzer (IS:2268-1994) with CM/L no. printed including making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 95 E-17/17.1.1 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR :1170mm (+/-10%) LED batten with min. lumen output 2200 lm 96 E-18/18.12.2 Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass coverand secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver& has a unique BIS R number withInput Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driverEfficiency >85%,THD(I) <10%Humidity 10% to 90% RH Working Temp -5C to 45C .driver current <750mA. The luminaireshall be BIS certified and Trade mark certified. Life ExpectancyEqual or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs.Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities forLED fixtures.(LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .LED Street Light fixture with Minimum lumen output 3700 lm 97 E-15/15.10 P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR 98 (E-15/15.7.3) Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR. 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) 99 E-15/15.16 Providing & Fixing ofextra down rod of 15 mm dia . ERW (Electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe including cutting, threading, drilling, fixing quarter pin etc as reqd.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 100 E-06/6.1.1.2 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR:6A to 32A rating 101 (E-6/6.2.1.2) Providing & Fixing of 240/415 V isolatorISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm.IP 20 contact protection and fitted in existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR Double pole isolator 63 A rating 102 (E-6/6.10.1.3) Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR Metal door (single phase) IK-09 and IP-43 with Metal end box8 Way (8+2) 103 (E-6/6.10.1.1) Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR Metal door (single phase) IK-09 and IP-43 with Metal end box4 Way (4+2) 104 E-17/17.9.3 Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulbin existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70,minimum life time of minimum25000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure A attacheded with this BSR. 9WATTS 105 E-14/14.2 Plate Earthingas per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying3 to 4 mtr. below the ground level with 20mm dia. G.I. B class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 106 E-14/14.6.9 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu purity purity >95%thimble etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR. 10 SWG G.I. ( Hot Dipped) Wire 107 (E-11/11.2.3.1) Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure A attached with this BSR10.0 Sq. mm 2 Core 108 E-07/7.21 Providing & Fixing of IS 11037:1984markednon modular socket size flush type 180 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 109 E-18/18.10.1 Providing & Fixing of IK08IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece constructionpowder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser andAluminium anodised with sand blast reflector. The System level Luminous efficacy ≥100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N)and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . Driver current <750mA.Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities forLED fixtures.(LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Minimum lumen output 2500 lm Post top Luminarie
