|
| 1 | M&L for disconnecting DG set 200 KVAfrom main lineand ovehauling,tuning up by the help of tool and plants and taking out all the components i.e.cylinder head, piston assembly, cylinder liner, connecting rod assembly, bearing and other part, cleaning, checking and carryout repair/replacement of unserviceable /worn out parts,including head machining, cleaning the chamber filling of lub.engine oil, reassembling all the parts, commissioning and testing on full load all as directed by Engr-in-Charge. Make:- Cummins Note –(i) New parts will be replaced by Genuine engine spare parts only.(ii) Engine oil and spare parts will be measured & paid separately as mentioned in respecive srl below of this schedule. |
| 2 | Supply only the following spare parts suitable for DG set 200 KVA as per srl 01 above :- |
| 3 | Piston assembly |
| 4 | Piston Ring |
| 5 | Piston Pin |
| 6 | Liner cylinder |
| 7 | CR bearing |
| 8 | Set of \"O\" ring |
| 9 | Intake valve |
| 10 | Exhaust valve |
| 11 | Valve seat |
| 12 | Valve guide |
| 13 | Valve sleeve |
| 14 | Engine gasket set |
| 15 | Rubber Hose Pipe set |
| 16 | Water pump |
| 17 | Timing oil seal |
| 18 | Filter set complete including Air filter |
| 19 | Taking out unserviceable Fuel Injection Pump from 200 KVA DG set and transportation to civil workshop foroverhauling, calibration and replacement of worn out partssuch as plunger, element, delivery valve, gear, oil seal, roller pin, spring rotor assembly etc including completetesting all as specified & directed. Make: Motorpal or equivalent as approved |
| 20 | Taking out Injector Nozzle by opening the tappet cover of the DG set 200 KVA from the engine and transportation to civil workshop for repair/replacement of unserviceable spares such as Barrel & Plunjer, retainer, injector cup, ball check and spring etc. complete and cleaning all the parts with the help of CTC, complete assembling, commissioning and installation the injector assembly with tappet cover packing complete and testing of DG set on full load all as specified and directed by Engr-in-Charge. Make: CumminsNote:-(New spare part shall be measured and paid seperately under item No 5 here in after) |
| 21 | Supply only following spare parts suitable for DG set 200 KVA:- |
| 22 | Barrel & Plunjer |
| 23 | Injector Cup |
| 24 | Retainer |
| 25 | Ball check |
| 26 | M&L for Disconnecting DG set 50 KVAfrom main line and ovehauling,tuning up by the help of tool and plants and taking out all the components i.e.cylinder head, piston assembly, cylinder, connecting rod assembly bearing and other part, cleaning, checking and carryout repair/replacement of unserviceable /worn out parts, cleaning the chamber filling of lub.engine oil, reassembling all the parts, commissioning and testing on full load all as directed by Engr-in-Charge. Make:- Kirloskar Note –(i) New parts will be replaced by Genuine engine spare parts only.(ii) Engine oil and spare parts will be measured & paid separately as mentioned in respecive srl below of this schedule. |
| 27 | Supply only the following spare parts suitable for DG set 50 KVA as per srl 06 above :- |
| 28 | Piston assembly |
| 29 | Piston Ring |
| 30 | Connecting bush |
| 31 | Liner cylinder |
| 32 | CR bearing |
| 33 | Set of \"O\" ring |
| 34 | Inlet valve |
| 35 | Exhaust valve |
| 36 | Valve seat |
| 37 | Valve guide and valve spring |
| 38 | high pressure fuel pipe |
| 39 | Engine gasket set complete |
| 40 | Rubber Hose Pipe set |
| 41 | Water pump |
| 42 | Timing oil seal |
| 43 | Filter set complete including Air filter |
| 44 | S&F Engine Control Assyalongwith required assecories including taking down unserviceable Engine Control Assy from the DG set 40 KVA to 200KVA complete all as specified and directed by Engr-in-Charge.Make: Cummins or equivalent as approved |
| 45 | S&F in replacement low lubricating oil pressure sensor alongwithconnected control wiring, relay etcincluding taking down unserviceable safety device complete all as specified & directed by Engr-in-Charge for following :- |
| 46 | DG set 20 KVA to 82.50 KVA |
| 47 | DG set 125 KVA to 400 KVA |
| 48 | S&F in replacement water safety device for high water temperature along withconnected control wiring, relay etc including taking down unserviceable items compete all as specified & directed by Engr-in-Charge for following :- |
| 49 | DG set 20 KVA to 82.50 KVA |
| 50 | DG set 125 KVA to 400 KVA |
| 51 | Taking out unserviceable FIP from DG set and transportation to civil workshop foroverhauling, calibration and replacement of worn out partssuch as plunger, element, delivery valve, gear, oil seal, roller pin, spring rotor assembly etc including completetesting all as specified & directed by Engr-in-Charge for following capacity of DG Set :- |
| 52 | DG set 20 KVA to 40 KVA |
| 53 | DG set 50 KVA to 125 KVA |
| 54 | Taking out choked injection nozzle from the engine assembly and transportation to civil workshop foroverhauling andreassembling after calibration of nozzleon admissible pressure,and replacementunserviceable parts such as injector element, kit injector,retainer injector cup and connected itmes, refixing in position, fixing Tappit cover packing set and adjustment by dial gauge complete with satisfaction as directed for following DG set :- |
| 55 | DG set 20 KVA to 40 KVA |
| 56 | DG set 50 KVA to 125 KVA |
| 57 | Taking out Turbo charger assembly from the DG set and transportation to civil workshop for repair and overhauling with replacement of unsv. turbo kit, tubo core completeof existing make and refixingto DG and testing air pressure all as specified and directed by Engr-in-Charge for following capacity :- |
| 58 | 30 to 125 KVA DG set |
| 59 | 200 KVA to 320 KVA DG set |
| 60 | S&F in replacement of solenoid switch for 7.5 to 30 KVA DG setcomplete with connection and testing on load all as specified and directed. |
| 61 | S&F in replacement of solenoid switch for 40 to125KVADG setcomplete with connection and testing on load all as specified and directed. |
| 62 | S&F in replacement of solenoid switch for 200 to 320KVADG setcomplete with connection and testing on load all as specified and directed. |
| 63 | Supply and fillingnew premium quality lubricating oil 15W/40 grade, confirming to IS complete all as specified & directed. Make:- Servo/Castrol/MAK/Valvoline |
| 64 | Supply & filling new radiator coolant complete all as specified & directed. Make TVS-Girling /K-Cool/ Castrol |
| 65 | S&F Engine Monitoring System EMS suitable for30 KVA to 320 KVA DG Set with complete programming, including taking down unserviceable EMS from the DG Set complete with proper connection and testing on full load with accuracy and proper functioning all as specified and directed by Engr-in-ChargeMake : Kirloskar or equivalent as approved |
| 66 | M&L for servicing/maint of DG set offollowing capacity complete with replacement of old lub oil, fuel filter, lub oil filter, air filtercleaning of oil tank,draining out complete engine oil from the sump and filling fresh oil as required and also checking starting system ,dynamo, metering devices etc including testing the DG Set for satisfactory performance and complete all as specified and directed by Engr-in-Charge. Note :- (i) New parts will be replaced by Genuine engine spare parts only.(ii)Replacement of unserviceable parts and Lubricating. oil shall be measured and paid separately under respective items of this schedule |
| 67 | DG set 7.5 KVA to 15 KVA |
| 68 | DG set 20KVA to 30 KVA |
| 69 | DG set 40 KVA to 62.50 KVA |
| 70 | DG set 82.50 KVA to 125 KVA |
| 71 | DG set200 KVA to 320 KVA |
| 72 | DG set400 KVA |
| 73 | Supply only following spare parts :- |
| 74 | Lub oil filter assy completesuitable for DG set 7.50 to 15 KVA |
| 75 | Lub oil filter assy completesuitable for DG set 20to 30 KVA |
| 76 | Lub oil filter assy completesuitable for DG set 40 to 62.50 KVA |
| 77 | Lub oil filter assy completesuitable for DG set 82.50 to 125 KVA |
| 78 | Lub oil filter assy completesuitable for DG set 200 to 320 KVA |
| 79 | Lub oil filter assy completesuitable for DG set 400 KVA |
| 80 | Air filter element completesuitable for DG set 20to 30 KVA |
| 81 | Air filter element completesuitable for DG set 40 to 62.50 KVA |
| 82 | Air filter element completesuitable for DG set 82.50 to 125 KVA |
| 83 | Air filter element completesuitable for DG set 200 to 320 KVA |
| 84 | Air filter element completesuitable for DG set 400 KVA |
| 85 | Fuel filtercompletesuitable for DG set 7.50 to 15 KVA |
| 86 | Fuel filter element completesuitable for DG set 20 to 30 KVA |
| 87 | Fuel filter element completesuitable for DG set 40 to 62.50 KVA |
| 88 | Fuel filter element completesuitable for DG set 82.50 to 125 KVA |
| 89 | Fuel filter element completesuitable for DG set 200 to 320 KVA |
| 90 | Fuel filter element completesuitable for DG set 400 KVA |
| 91 | Super by pass/Fuel filter secondary/water seperator suitable for DG set 20 to 30 KVA |
| 92 | Super by pass/Fuel filter secondary/water seperator suitable for DG set 40 to 62.50 KVA |
| 93 | Super by pass/Fuel filter secondary/water seperator suitable for DG set 82.50 to 125 KVA |
| 94 | Super by pass/Fuel filter secondary/water seperator suitable for DG set 200 to 320 KVA |
| 95 | Super by pass/Fuel filter secondary/water seperator suitable for DG set 400 KVA |
| 96 | Taking down brunt unserviceableAutomatic Voltage Regulatorassy from alternator of DG set by disconnecting its electrical connections, supply and fixing new AVR suitable for 20 to 125 KVA DG Set including connecting all electrical connections. Testing voltage after starting engine and setting properly if a difference all as specified and directed. |
| 97 | Supply, fixing and filling the following items for DG Set of various capacity to be replaced under various items of schedule:- |
| 98 | Battery terminals brass bolt type heavy duty with clamp and nut bolts with washersuitable for gripping the battery lead. |
| 99 | Copper cable 95sqmmsingle core multiwired with copper lugs and suitable clamps as battery lead. |
| 100 | Distilled water. |
| 101 | S&F fuel pipe of DG set any capacity includingfixing with clamps and tightening arrangementcomplete with testing and checking all as specified and directed. |
| 102 | S&F Rubber hose pipe set complete with clamp and nut bolts with fixing with replacement of worn out hose pipe of following capacity DG set complete all as speclified and directed. |
| 103 | DG set 7.5 to 30 KVA |
| 104 | DG set 40KVA to 125 KVA |
| 105 | DG set 200 KVA to 400 KVA |
| 106 | Taking out existingunserviceable feedpump assembly from the engine, S&F new feed Pump of existing make complete with proper connection all as specified and directed for follwing capacity of DG set :- |
| 107 | DG set 15 KVA to 30 KVA |
| 108 | DG set 50KVA to 125KVA |
| 109 | DG set 200 KVA |
| 110 | Taking down radiator assyof following DG setfrom engine base frame by descrewing complete nuts & bolts, transporting to civil work shop cleaning complete, tubes , fins etc including soldering leakage portion mac solution should be used in cleaning Roding tube with prope size of steel stick. Transporting back to DG set re installing by using gasket set, Hose pipe set with steel adjustable clamp complete Replacing rubber Hose set by taking out old Hoses with Gubli clips complete, reassembling, commissioning and testing on full load pressure complete all as specified and directed. Note :-The unitrate includes the cost ofall material required for functioning of radiator assembly & no extra payment will be made. |
| 111 | DG set 30 to 62.5 KVA |
| 112 | DG set 82.5 KVA to 125 KVA |
| 113 | DG set 200 to 400 KVA |
| 114 | Taking down old self starter12Vfrom engine, repairing/overhauling, reassembling testing including ensuring smooth functioning by replacement of following spare parts complete all as specified and directed:- |
| 115 | Armature assy |
| 116 | Vendex pinion |
| 117 | Carbon brush holder with carbon set |
| 118 | Electrical coil |
| 119 | Taking down old self starter24Vfrom engine, repairing/overhauling, reassembling testing including ensuring smooth functioning by replacement of following spare parts complete all as specified and directed:- |
| 120 | Armature assy |
| 121 | Vendex pinion |
| 122 | Carbon brush holder with carbon set |
| 123 | Electrical coil |
| 124 | Supply, fixing and installation of Lead acid Battery maintenance free with various DG set with replacement of old for depositing to MES stores complete of following rating. |
| 125 | Battery 12V, 100 AH Make: Exide/Amaron/ TataGreen |
| 126 | Battery 12V, 150 AH Make: Exide/Amaron/TataGreen |
| 127 | Battery 12V, 180 AH Make: Exide/Amaron/TataGreen |
| 128 | S&F in repair/replacement of unserviceable or broken Door hinges suitable for any capacity and any size canopy ofDG set at different locations complete all as specified and directed. |
| 129 | Taking down old/unserviceable control wiring by disconnecting unsv. AMF panel any capacity, M&L for complete rewiring of AMF panel with suitable size of copper cable by disconnecting all its electrical connection and checking all loose connectingof accessories and tightening properly, cleaning of carbonised panelby the help of carbon tatra chloride and welding of panel door and supply and fixing door hinges and locking arrangements, LT jointing kits for incoming and out going cables and other connected accessories,complete commissioning ,testingto the entire satisfaction of the Engr-in-Charge. |
| 130 | S&F in repair/replacement the following items in AMF/LT Panel :- |
| 131 | MCB TPN 415V 32A \"C\" Series. Make:- L&T/ Legrand/Schneider as approved |
| 132 | MCB TPN 415V 63A \"C\" SeriesMake:- L&T/ Legrand/Schneider as approved |
| 133 | MCB SP 6 to 32A \"C\" Series. Make:- L&T/ Legrand/Schneider as approved |
| 134 | MCB SPN 32A \"C\"series. Make:- L&T/ Legrand/Schneider as approved |
| 135 | Air Break Contactor 2NO+2NC 240/415V AC with auxiliary contact blocksMake : L&T/ C&S / Siemens as approved |
| 136 | VMR 3P 415V. Make: Proton/ Minilec or equivalent as approved |
| 137 | ETM DI timer 12V/24V DC. Make:- L&T/ Siemens/ Minilec as approved |
| 138 | ETM DI timer 240V/415V AC. Make: L&T/ Siemens/ Minilec as approved |
| 139 | On delay timer 5-100 sec. 240V AC. Make:- L&T/Siemens or equivalent as approved |
| 140 | Copper Lugs 35 sqmm |
| 141 | Copper Lugs 95 sqmm |
| 142 | CT ratio 200/5. Make:- L&T/AE or equivalent as approved |
| 143 | Two position selector actuator with 1NO+1NC contacts. Make: Siemens or equivalent as approved |
| 144 | Digital panel meter, multifunctional type3 phase, 4 wire, 5A balance 90-300 V AC, Model A Class 1.Make :- L&T, AE or equivalent as approved |
| 145 | Ammeter 0-500A with CTs of size 96x96mm panel mounting digital type accuracy class -1. Make :L&T/ Rishab/AE as approved |
| 146 | Voltmeter 0-500V with CTs of size 96x96mm panel mounting digital type accuracy class -1. Make :L&T/ Rishab/AE as approved |
| 147 | Phase Indication lamp LED type of any colour as per site requirement directed by Engr-in-Charge. |
| 148 | Fuse links kitkat type 230V 6A to 32A. |
| 149 | Start and Stop push button 3 NO , including NO and NC Contacts |
| 150 | 8 /11 Pin relay 12V/24V DC with base. Make : L&T / Pla/Omron as approved |
| 151 | Rotary switches or mode selector switches 10A 3P, 3W Make : L&T/SCI or equivalent as approved |
| 152 | S&F 8/11 Pin relay 240V/415V AC with base complete all as specified and directed. Make:L&T/Pla/Omron as approved |
| 153 | S&F in replacement of Thermal Overload relay having a range of 24-40 A suitable for 62.50 to 125 KVA AMF Panel complete all as specified and directed. Make:L&T/Siemens/C&S as approved |
| 154 | M&L for replacingpanel door locks brass HEAVY DUTY Allen key operated suitable to match the existing one including taking down the existing defective one all as directed. |
| 155 | S&F Under voltage/Over voltage relay 240/415V AC 3 phase, 4 wire, time & power ON-delay 1-10 Sec. Complete all as specified and directed. |
| 156 | S&F On delay Multifunction ET timer 24 - 240 V complete all as specifed and directed. Make: L&T/Siemens or equivalent as approved |
| 157 | S&F in replacementon line battery charger 12Volt complete with connection, testing all as specified and directed. Make:Teknika/NHP/Stronger as approved |
| 158 | S&F in replacementon line battery charger 24Volt complete with connection, testing all as specified and directed. Make:Teknika/NHP/Stronger as approved |
| 159 | Taking down alternator battery charger system 12 V from existing DG set and rapair of alternator by replacing of following spare parts with greasing, servicing, polishing completeand refixing in DG set complete and testing all as specified and directed :- |
| 160 | Rectifier assembly |
| 161 | Stator coil |
| 162 | Cut out |
| 163 | Carbon set |
| 164 | Taking down alternator battery charger system 24 V from existing DG set and rapair of alternator by replacing of following spare parts with greasing, servicing, polishing completeand refixing in DG set complete and testing all as specified and directed :- |
| 165 | Rectifier assembly |
| 166 | Stator coil |
| 167 | Cut out |
| 168 | Carbon set |
| 169 | S&F in replacement Fan belt for the following DG Sets complete all as specified and directed by Engr-in-Charge:- |
| 170 | 15 KVA to 30KVA DG Set |
| 171 | 50 KVA to 125 KVA DG Set |
| 172 | 200 KVA to 320KVA DG Set |
| 173 | 400 KVA DG Set |
| 174 | Taking out fuel tank from the DG set any capacity by disconnecting its connection from the DG set and carrying out necessary checking for leakage and welding work for make tank leak proof, cleaning of fuel tank by removing all the sludge material deposited in the tank and also cleaning of chocked fuel pipe including replacing of unserviceable/broken Gate valve, elbows, sockets, etc. complete all as specified and directed and re-installing to the DG set complete all as specified and directed. |
| 175 | S&F in replacement of ML-06 Power Contactor any type. (Make- L&Tor equivalent as approved) in existing panel/ location and connection incl necessary alteration in panel/ door as required for proper fixing & connection complete all as specified and directed. |
| 176 | S&F in replacement of Power Contactor 200 Amp 4P (Make- L&Tor equivalent as approved) in existing panel/ location and connection incl necessary alteration in panel/ door as required for proper fixing & connection complete all as specified and directed. |
| 177 | S&F in replacement of Power Contactor 250 Amp 4P (Make- L&Tor equivalent as approved) in existing panel/ location and connection incl necessary alteration in panel/ door as required for proper fixing & connection complete all as specified and directed. |
| 178 | S&F maintenance free dry type battery 12 V, 65 AH with various DG Set with replacement of old for depositing to MES stores complete all as specified and directed. Make Pulse (Cummins) or equivalent as approved |
| 179 | S&F in replacement MCCB 250 Amps,4 pole, breaking capacity 36 KA at 415 volts, 50 HZ, including necessary connection complete all as specified and directed. Make :- Legrand DPX³ 250 Cat No 420249 or equivalent Schneider/ Siemens as approved |
| 180 | S&F CT Coil of Ratio 300/5 of alternator of DG Set 125 KVA complete all as specified and directed by Engr-in-Charge. Make: Stamford or equivalent as approved |
| 181 | S&F in replacement of ON load Changeover switch 250 Amp, 4 Pole in existing panel/ location and connection incl necessary alteration in panel/ door as required for proper fixing & connection complete all as specified and directed. |
| 182 | S&F in replacement of ON load Changeover switch 125 Amp,4 Pole with enclocure at various location and connection incl necessary alteration in panel/ door as required for proper fixing & connection complete all as specified and directed. |
| 183 | S&F Relay Card 12/24V for suitable DG Set and including taking down old unserviceable relay card from existing DG Set complete all as specified and directed by the Engr-in-Charge. |
| 184 | S&F Fuel guage ofDG Sets of any capacity and including taking down old unserviceable fuel guage from existing DG Set complete all as specified and directed by the Engr-in-Charge. |
| 185 | Taking out aerator motor pumping set from existing foundation after disconnecting of elect connection & necessary pipe line by opening nut bolts etc and dismantling the aerator motor pumping set & M&L for rewinding to aerator motor of capacity upto15 HP of any make with supper enamelled copper winding wire of existing size and quantity including insulating materials ie varnish , sleeves etcincluding dismantling for repair and commissioning after repair complete all as specified and directed by Engr-in-Charge. |
| 186 | Taking out non clog submesible pump set from existing shoak wellafter disconnecting of necessary pipe line by opening nut bolts etc and dismantling the pump of any make for carrying out the repairs, reassembling the same including replacement of wornout nuts,bolts and washers etc reinstalling,testing and making good all water line and electric connections to ensure proper functioning entire unit and commisioning complete all as specified and directed by Engr-in-charge for the following capacity of pump sets :- Note :- spare parts shall be measured and paid separately under relevant items |
| 187 | (a) Non clog submesible pump set 2 HP |
| 188 | (b) Non clog submesible pump set 3 HP |
| 189 | (c) Non clog submesible pump set 5 HP |
| 190 | (d) Non clog submesible pump set 15 HP |
| 191 | M&L for rewinding to undermentioned non clog submesible pump set of any make with supper enamelled copper winding wire of existing size and quantity including insulating materials ie varnish , sleeves etc completeincluding dismantling and commissioning after rewinding complete all as specified and directed by Engr-in-Charge:- |
| 192 | (a) Non clog submesible pump set 2 HP |
| 193 | (b) Non clog submesible pump set 3 HP |
| 194 | (c) Non clog submesible pump set 5 HP |
| 195 | (d) Non clog submesible pump set 15 HP |
| 196 | S&F in replacement ofBearing set (set of 02) for non clog submersible motor of capacity upto 10HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 197 | S&F in replacement ofOil seal chamber for non clog submersible motor of capacity upto 10 HP (Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 198 | S&F in replacement ofOil seal for non clog submersible motor of capacity 5- 10 HP (Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 199 | S&F in replacement of\"O\" ring set for non clog submersible motor of capacity 5-10 HP (Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 200 | S&F in replacement ofBearing set (set of 02) for non clog submersible motor of capacity upto 2 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 201 | S&F in replacement ofOil seal chamber for non clog submersible motor of capacity 2 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 202 | S&F in replacement ofOil seal for non clog submersible motor of capacity 2 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 203 | S&F in replacement of\"O\" ring set for non clog submersible motor of capacity 2 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 204 | S&F in replacement of Allen scew for non clog submerbsible motor .5HP/1.5HP/ 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 205 | S&F in replacement of screwed adjuster for non clog submerbsible motor .5HP/1.5HP/ 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 206 | S&F in replacement of Impeller nut cover for non clog submerbsible motor .5HP/1.5HP/ 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 207 | S&F in replacement of Hex bolts and nuts including washer for non clog submerbsible motor .5HP/1.5HP/ 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 208 | S&F in replacement of cable cap for non clog submerbsible motor 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 209 | S&F in replacement of upper seal for non clog submerbsible motor 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 210 | S&F in replacement of lower seal for non clog submerbsible motor 2HP/ 4HP/ 5HP complete all as specified and directed. |
| 211 | S&F in replacement of Allen scew for non clog submerbsible motor 15HP complete all as specified and directed. |
| 212 | S&F in replacement of screwed adjuster for non clog submerbsible motor 15 HP complete all as specified and directed. |
| 213 | S&F in replacement of Impeller nut cover for non clog submerbsible motor 15 HP complete all as specified and directed. |
| 214 | S&F in replacement of Hex bolts and nuts including washer for non clog submerbsible motor 15HP complete all as specified and directed. |
| 215 | S&F in replacement of cable cap for non clog submerbsible motor 15 HP complete all as specified and directed. |
| 216 | S&F in replacement of upper seal for non clog submerbsible motor 15 HP complete all as specified and directed. |
| 217 | S&F in replacement of lower seal for non clog submerbsible motor 15 HP complete all as specified and directed. |
| 218 | S&F in replacement ofMechanical seal (set of 02) for non clog submersible motor of capacity 2 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 219 | S&F in replacement ofMechanical seal (set of 02) for non clog submersible motor of capacity 3 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 220 | S&F in replacement ofMechanical seal (set of 02) for non clog submersible motor of capacity 5 HP ( Make :Kishore/ Kirloskar/ KSB/ Crompton as approved) complete all as specified and directed by Engr-in-Charge. |
| 221 | M&L for Gear oil suitable for aerator motor/pumping set. Make Veedol/Power gear/MAK as approved |
| 222 | M&L for replacement of compressor oil suitable for aerator motor/ pumping set. Make Veedol/Power gear/MAK as approved |
| 223 | Labour for taking out sludge from sand filter bed and transportation todepositing the existing plateform, cleaning of sand filter complete in side and out side removing of unwanted vegetation in sand filter complete all as specified and directed by Engr-in-Charge. |
| 224 | Labour for taking out sludge from existing plateform and transportation todepositing where directed by Engr-in-Charge, cleaning of Plateform complete, removing of unwanted vegetation in plateform complete all specified and directed by Engr-in-Charge. |
| 225 | M&L for clean dry sand (as specified for filter bed) laid in filter bedfor bedding, complete all as specified and directed by Engr-in-Charge. |
| 226 | M&L for pumping out sewage water mixed with sludge from aeration tank containing two tanks each of size 30 Mtrs x15 Mtrsx3 Mtr deep , detwatering of sludgefrom the sump by the help of pump, complete all as specified and directed.Note :- For the purpose of measurement depth of contents (Water/Sludge) shall be measured not exceeding 2.5 Mtr ). |
| 227 | All as per item No 88 above but from clarifier tank of 16 Mtr dia and 3 Mtr depth complete all as specified and directed. |
| 228 | Removing sedimented sludge by excavating not exceeding 75 cm deep (average) and getting out from aeration tank for removing out side of MOD and deposited where directed at a place allotted by local muncial/ corporation including spreading of sufficient bleachig powder over the sluge to take all precuative health hazzored complete all as specified and directed. |
| 229 | All as per item No 90 above but sump well 6 Nos sump well each of dia not less than 3 Mtr and average depth of excavation n.exc 90cm complete all as specified and directed. |
| 230 | M&L for opening choked line of sump well upto a depth of 10mtr from ground level with necessary tool and plant to make through the sludge from one system to another complete all as specified and directed. Note: 1. The T&P will be given by the contractor. 2. The contractor should be fully responsible for safety of the labourer engaged during the said work. |
| 231 | S&F in replacement non clog submersible pump controller in sheet enclosure Type MU-G6 DOL for three phase motor 415 volts, 50 HZ, 5 HP, 6-10 Amps relay range including suitable size LT panel, outdoor type, for mounting/fixing the pump controller, cubical compartmentalised of 2mm thick CRCA sheet powder coated front door openable with angle iron 45x45x5 mm frame bottom of the panel board, grouted by using PCC foundation 1:2:4 type C1 with 20 mm graded stone aggregate, thimbling and cable entry boxes with cable gland inculding painting with two coat of powder coated paintingover a coat of red oxide primercomplete all specified and directed. Make Cat Part No. SS97756COVO of L&T or equivalent inLegrand or equivalent as approved |
| 232 | Supply and laying in replacement of PVC flexible suction pipe of size 50mm dia, thickness 6 with all fitting laid in sump complete all as specifeid and directed. Make: Supreme / Premier / Finolex as approved |
| 233 | Supply and laying in replacement of PVC flexible suction pipe of size 80mm dia, thickness 6mm with all fitting laid in sump complete all as specifeid and directed. Make: Supreme / Premier / Finolex as approved |
| 234 | Supply and laying in replacement of Nylone rope of 24mm thick, complete all as specifeid and directed. |
| 235 | M&L for welding LT panel i.e. door front/ rear, hinges, compartment etc and making good the existing surface after necessary work complete all as specified and directed. Note: 1. Necessary electric shutdown to the panel will be given before the work. 2. Painting work should be measured seperately as schedule of work. |
| 236 | Cleaning the area as directed by cutting grasses, bushes etc and making neat and clean the area complete all as spcified and directed. |
| 237 | S&F PVC Copper cable 4 Sqmm 6 core round type complete all as specified and directed. Make Havells/Plaza/Finolex as approved |
| 238 | Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material |
