Tender For Petty Repair Of B/R Works, Welcome Maint In Md Accn And Periodical Services To Bldgs, Repair To Plaster, Fins, Facia And Tank Cleaning And Misc B/R Repair To Otm And Tech Area Buildings And Mes Installations & Officers At Af Stn Kasauli Under G
Tender Value
45 Lakhs
Estimated cost
Bid Submission
07 Jun 2025
0 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kasauli → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
PETTY REPAIR OF B/R WORKS, WELCOME MAINT IN MD ACCN AND PERIODICAL SERVICES TO BLDGS, REPAIR TO PLASTER, FINS, FACIA AND TANK CLEANING AND MISC B/R REPAIR TO OTM AND TECH AREA BUILDINGS AND MES INSTALLATIONS & OFFICERS AT AF STN KASAULI UNDER GE KASAULI.
BOQ
| Sl. No. | Item Description |
| 1 | Schedule \"A\" Section - I |
| 2 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal the rubbish/ demolished material outside defence land, complete all as specified and directed |
| 3 | Material and labour for applying water proofing treatment to sunken slab comprising of the following specifications complete all as specified.(i)Cleaning of roof surface with mechanical means i.e. wire brush/air blower etc. andremove all loose /unsound material,dirt,dust etc.(ii)Providing and laying water proofing treatment of sunken portion of WCs, bathroom etc by applying cement slurry mixed with acrylic based polymer modified cementitous composit compound coating of make as approved in Technical Instruction 5/2003(iii)First layer of cement slurry @ 0.488 Kg/Sqmmixed with acrylic based polymer modifiedcementitious composite compound @ 0.253 Kg/Sqm of approved make and allowed layer to air cure for 04 hours.(iv)Second layer of cement slurry @ 0.244 Kg/Sqmmixed with acrylic based polymer modifiedcementitious composite compound @ 0.126 Kg/Sqmand allowed layer to air cure for 04 hours followed with water curing for 48 hrs .(v) 200 micron thick polythene film pasted with the hepl of adhesive shall be provided over treatment . |
| 4 | item No. 2.00(contd....)Note :-(i) Concrete for sunken slabs shall be mixed with WP compounds as per manufacture instruction(ii) The slope of slab shall be 1:20 towards the corner of outer walls and GI pipe of 50-80mm dia ( Medium grade ) be inserted at corner projecting out side 20 cm . The sunken slab shall invariably rest on inverted beam from sides.(iii) 15mm plaster mixed with WP compound shall be provided whileconcrete is still green .If any leakage/dampness is seen in ceiling exposed below then a proper treatment is given and again tested befoe passing for next stage . (iv) Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound.(v) P/Straps and Nahani/Floor traps with long arm shall be provided as per latest instruction .(vi) Testing of all trap & joint and sunken slab shall be as per IS-1742 before filling and tilling of sunken slabs, including smoke test .(vii)The water proofing treatment shall be carried out by the manufacturer or his authorised applicators and contractor shall also provide 07 yearsGuranttee forwater proofing treatment carried out in the work. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work. |
| 5 | Material andlabour for plain cement concrete 1:5:10 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed. |
| 6 | Material and labour for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as levelling course, finished even and fair to receive floor finishes, complete all as specified and directed. Note- This item shall not be executed in the location, where dismantling of tiles work have been done. |
| 7 | supply and fixing 40 mm dia GI pipe , medium grade as in spout for sunken floor,fixed as in wall inside end fixed with wire netting and external bevelled edge at 45 degree, complete allas specified and directed. |
| 8 | Supply andfixing in repair, bib tap screwed down high pressure, cast copper alloy, chromium plated, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified.(Note : Weight of bib tap shall not be less than 0.400 Kg and Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. |
| 9 | Supply and fixing in repairs stop valves, 15 mm dia pipe,cast copper alloy, chromium plated, ISI marked,screwed down, high pressure with crutch or butterfly handle (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete all as specified. (Note : Weight of stop valve shall not be less than 0.575 Kg and Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. |
| 10 | Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed . |
| 11 | Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and directed . |
| 12 | Supply and fixing steel water tubing of 15 mm bore, medium grade galvanized , laids in floor , wall and on ceiling, complete all as specifiedand directed . |
| 13 | Supply and fixing steel water tubing of 20 mm bore, medium grade galvanized , laids in floor , wall and on ceiling, complete all as specifiedand directed . |
| 14 | Refixingsteel water tubing of 15 mm bore in new or old position withall new fittings as required, laids in floor , wall and on ceiling, complete all as specifiedand directed. |
| 15 | Refixingsteel water tubing of 20 mm bore in new or old position withall new fittings as required, laids in floor , wall and on ceiling, complete all as specifiedand directed. |
| 16 | Supply and fixed (in repair), vitreous china wash down water closet pedestal pattern, coloured including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap,plastic water closet seat cover with mild steel chromium plated hingesand chromium plated jet spray suitable for EWC with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified. |
| 17 | Supply and fixed (in repairs) vitreous China coloured squatting pan of Orissa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including making good to floor surface with the existing surface and connection to flush pipe complete all as specified. |
| 18 | Supply andfixing in repair,vitreous china wash hand basin white flat back of size 550x440mm excluding CI brackets but including PVC waste pipe, PVC connections and chromium plated waste coupling, etc.,complete all as specified. Note- Old pillar tap and other accessories are reused in this items. |
| 19 | Supply and fixing 110mm dia of outlet, PVC (SWR) floor trap plain with grating including jointing with solvent cement, complete all as specified.(Note- UPVCfittings shall be conforming to BS 4515 DIN 19531 and DIN 19534) |
| 20 | Supply and fixing 110mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) |
| 21 | Supply and fixing110 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified.(Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) |
| 22 | Supply and fixing (in repair), PVC connections 45cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified. |
| 23 | Supply and fixing (in repair), PVC connections 60cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified. |
| 24 | Supply andfixing ( in repair ) galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified and as directed. |
| 25 | Hacking out old broken glasses of any description and in any position from wooden/steel frames fixed with oil putty or beads etc. and removing from site, complete all as specified. |
| 26 | Supply andfixing for sheet glass 4mm thick, ordinary quality and glazing with oil putty, in square not exceeding 0.5 Square metre in each pane or with wooden beads to wooden shutters, complete all as specified. |
| 27 | Supply and fixing figured glass 4mm thick pin head type, in squarenot exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified. |
| 28 | Cutting or uprooting completely grass tree/ plants (upto 30 cm girth) from wall or any part of building upto triple story buildings, removing off the rubbish off the premises making good disturbed portion and filling holes in cement mortar (1:3) or PCC (1:2:4) to match with the existing surfaces, complete all as specified. |
| 29 | Supply and fixing 10 litre capacity virgin polypropylene cistern, ISI marked, coloured at low level complete with PVC bend/flush pipe and making all connectionincluding taking down existing high or low level unerviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified. |
| 30 | Takingdown pelmet box with curtain rod, making good the disturbed surface with the surrounding surface and supply andfixing of mild steel 32mm dia, 1.6mm thick, PVC coated, fancy type, heavy dutydrapery rod, complete all as specified and as directed. |
| 31 | Material andlabour for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. |
| 32 | Material and labour for premium quality, glazed coloured ceramic tiles 300 x 450 x 7mm thick on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified. |
| 33 | Material andlabour for premium quality, joint free, non skid, coloured ceramic 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm tiles, as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and includingcement screed bed 15mm thick in cement mortar (1:4) base, complete all as specified. |
| 34 | Material andlabour for premium quality, joint free, non skid, coloured ceramic 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm tiles, as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and includingcement screed bed 15mm thick in cement mortar (1:4) base, complete all as specified. |
| 35 | Material and Labour for Easing , adjusting, greasing of sliding rolling shutter of height not exceeding than 4.00 Mtr including minor repair/welding etc to sliding door leaf for noiseless smooth operation (area of door leaf not exceeding 10 Sqm and height not exceeding 4.00 Mtr, complete all as specified. |
| 36 | Material and labour for repairing existing aluminium door/windows, area of shutter not exceeding 3 sqm each, in following steps, complete all as specified and as directed.(a) Taking down shutter from the frame.(b) Replacement of jointing cleats, glazing clips, rubber packing, snap beading, screws etc complete to make the shutter fully functional (c)Refixing the shutter in same location after carrying out repairs. |
| 37 | Supply and fixing water storage tank 500 ltr capacity HDPE double layer ISI marked fixed andhoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut , ISI marked, screwed andsuitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site,complete all as specified. |
| 38 | Supply and fixing water storage tank 1000 ltr capacity HDPE double layer ISI marked fixed andhoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut , ISI marked, screwed andsuitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site,complete all as specified. |
| 39 | Supply and fixingbrass valve high pressure with polythene float and flynut , screwed for iron pipe size 20mm bore, complete all as specified |
| 40 | Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof covering, complete all as specified and directed. |
| 41 | Supply andfixing 0.63 mm thick galvanised corrugated mild steel sheeting, class-8 with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts and washers, ISI markedin roofs, walls etc. with grade of zink coating 275, complete all as specified and directed. |
| 42 | Supply andfixing (in repairs) for 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with L type or J type or cranked hook bolt in roof, wall etc. complete all as specified and as directed |
| 43 | Supply andfixing 0.80 mm thick Plain, galvanized mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zink coating 275 complete all as specified and directed. |
| 44 | Supply and fixing of Pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. |
| 45 | Supply and fixing ofPre-painted galvalume aluminuim zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. |
| 46 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified and directed. |
| 47 | Supply and fix 600mmx600mmx6mm thick ‘E’ Board Classicas in false ceilingincluding supply and fixingGI ‘Tee” grid frame work made of special section of M.S galvanized sheet 0.30mm thick , bottom portion painted with cellular nitro painting, warping the suspending wire around theexistingwooden/steel purlin /rafterfor suspending grid frame work of size 605mmx605mm suspendedwith 4 mm dia GI wire @ 1200mm c/c on main Tee and fixed to T-grid with the help of level clip oras per manufacturer direction.The section consisting of main Tee 37mmx24mmx0.60mm, cross runner tee 37mmx24mmx0.60mm and perimeter angle of 24mmx24mmx0.50mm thick. Perimeter angle to be fixed to wall with GI screw of 40mm long @ 450 mm c/calong the perimeter of wall including applyingtwo coats of distemper oil emulsion complete all as specified and directed.Note : Contractor shall produced voucher andmanufacture test certificateto Engineer-in-charge before claiming of payment. |
| 48 | Dismantling of wrought iron or mild steelwork of any description not otherwise specially providedcomplete all as specified and directed. |
| 49 | Supply andfixing mild steel, rolled sections as in main orcross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting platesconforming to grade Fe-410(Gde 250), complete all as specified and directed. |
| 50 | Demolition ofcement concrete in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and directed. |
| 51 | Material and labour for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in sub base to floor, complete all as specified. |
| 52 | Material andLabour for cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed, set jointed and pointed in neat cement slurry with grey cement and pigments, in floors, cut and polishedover and including 20 mm thick (average thickness) cement screed (1:4) base, complete all as specified. |
| 53 | Material andlabour for preparation of old treated surfaceand applying one coats of oil bound distemper with hand roller, over a coat of primeronplastered surface complete all as specified and directed |
| 54 | Material andlabour for complete removal of existing treatment on surfaces of wall by using appropriate technique as approved by Engr-in-chargefor complete removal of all layers of old treatment and reaching upto old plastered surface and applying two coats of oil bound distemper with hand roller, over a coat of primeronplastered surface complete all as specified and directed |
| 55 | Material andlabour for complete removal of existing treatment on walls including washing down, rubbing down and applying anti-fungal treatment as required andapplying one coats of weather shield Acrylic exterior paint over a coat of primer, complete all as specified and directed. |
| 56 | Material andlabour for Preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 57 | Material and Labour for Preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.. |
| 58 | Material and Labour for taking down cement or cement lime plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete,including removal of rubbish outside MoD land complete all as specified and directed. |
| 59 | Material andLabour for 15mm thick rendering on fair surfaceof brick work, concrete surfaces in cement mortar 1:4 including with WPC @2% by weight of cement or as per manufacturer’s instructions,finished even and fair, complete all as specified. |
| 60 | Material andlabour for 10mm thick rendering in cement mortar (1:6)on surface of any description and any height of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified. |
| 61 | Material andlabour for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer, complete all as specified. |
| 62 | Material and labour for two coat of cement base paintover newly plastered surface of any heightincluding preparation of surface complete all as specified and directed |
| 63 | Supply andfixingFloor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length of cover plate 150 mm, ISI marked complete all as specified and as directed. |
| 64 | Taking down wooden chowkats or frames areanot exceeding 1.50 Square metre(w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fastsand making good the disturbed portion of jambs andadjoining surfaces to match with existing finish, complete all as specified and as directed. |
| 65 | Taking down wooden chowkats or frames area exceeding 1.50 Square metre andnot exceeding 4.00 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfaces to match with existing finish, complete all as specified and as directed. |
| 66 | Taking down shutters of any description but not exceeding 1.00 Sq.m eachfrom chowkhat, complete all as specified. |
| 67 | Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat complete all as specified. |
| 68 | Supply andfixing for 2nd class hard wood plain, solid straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified. |
| 69 | Supply andfixing for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290-Gde E-165, complete all as specified and as directed. |
| 70 | Material and Labour for plain cement concrete 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregates) as in fixing of hold fasts, copings, bed plates,kerbs or mud stops,lintels upto 1.50m span, plinth courses , seismic and other bands and the like, finished the surface fair andeven, including necessary form work complete all as specified and directed. Note- If reinforced concrete, reinforcement shall be measured and paid for separately. |
| 71 | Supplyand fixing factory made flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, ISI marked complete all as specified. Note : Contractor shall produced voucher andmanufacture test certificateto Engineer-in-charge before claiming of payment. |
| 72 | Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed .Note : Contractor shall produced voucher andmanufacture test certificateto Engineer-in-charge before claiming of payment. |
| 73 | Suppling and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification complete all as specified and as directed. |
| 74 | Suppling and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement,fixing in the frame as per specification complete all as specified and as directed. Note : Contractor shall produced voucher andmanufacture test certificateto Engineer-in-charge before claiming of payment. |
| 75 | Supply andfixing mild steel butt hinge of 100mm length, cold rolled, medium weight, ISI marked complete all as specified and directed. |
| 76 | Supply andfixing stainless steel butt hinge of 75mm length,medium weight, ISI marked complete all as specified and directed. |
| 77 | Supply andfixing200 mm mild steel barrel tower bolt, ISI marked, stove enameled black with bright bolt and fixed, complete all as specified and directed. |
| 78 | Supply andfixing300 mmmild steel sliding door bolt, ISI marked, stove enameled black, with bright bolt not less than 16mm diawith and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified and directed. |
| 79 | Supply andfixing aluminum handle, cast type, anodized 100mm long, complete all as specified and directed. |
| 80 | Supply and Fixing 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specifiedand directed |
| 81 | Supply andfixing framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, angle iron chowkats for door ,barred iron doors, ladders framed balusters, walk ways, railings, and similar work conforming to Fe-290-Gde E-165 complete all as specified. |
| 82 | Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified. |
| 83 | Supply and fixingHealth Faucet with 8mm dia, 1metre long flexible tube and wall hook complete, all as specified and directed . |
| 84 | Supply andfixing aluminium (Die cast) body door closer, hydraulically regulated, designation No. 1, universal type, suitable for door shutters up to 700mm in width and of weight not more than 35kg complete all as specified and as directed. |
| 85 | Supply and fixed5.5mm thick looking mirror of selected quality, beveled edge 450mmx600mm glass mounted on 6mm thick AC building board with aluminiumbeading andrubber packing and fixed to wall with wooden plug with chromium plated brass screw and cup washercomplete all as specified. |
| 86 | Supply and fixing in repair 20mm ballvalve ,high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball ISI ( Minimum weight 210 gms) screwed & suitable for iron pipe 20mm bore complete all as specified and directed |
| 87 | Supply andfixing in repairs 15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified.(Note : Weight of pillar tap shall not be less than 0.665 Kg) |
| 88 | Supply and fix 75mm dia of outlet, PVC (SWR) floor trap plain with grating including jointing with solvent cement, complete all as specified..(Note- UPVCfittings shall be conforming to BS 4515 DIN 19531 and DIN 19534) |
| 89 | Supply and fixing 75mm diaUPVC, soil waste drain pipe, type ‘B’ ,conforming toIS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall, complete all as specified anddirected.(Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985) |
| 90 | Supply and fixing 75 mm bore UPVC (SWR) plain bend any radius including jointing with solvent cement, complete all as specified.(Note- UPVCbends shall be confirm to BS 4515 DIN 19531 and DIN 19534) |
| 91 | Supply and fixing 75 mm bore UPVC (SWR), branch piece, single Y (equal or unequal), including jointing with solvent cement, complete all as specified. |
| 92 | Supply andfixing in repairs aluminum anodized, barrel tower bolt of extruded section 125mm long, ISI marked, complete all as specified and directed. |
| 93 | Supply andfixing in repairs300 mmaluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed. |
| 94 | Supply andfixing in repairs mild steel butt hinge of 100mm length, cold rolled, medium weight, ISI marked complete all as specified and directed. |
| 95 | Supply andfixing in repairsmild steel butt hinge of 75mm length, cold rolled, medium weight, ISI marked complete all as specified and directed. |
| 96 | Labour for welding in repairs exceeding 2.5 cm but not exceeding 5 cm in length, thickness of metal to be welded not exceeding 6 mm, complete all as specified and directed. |
| 97 | Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat and refixing in the same opening after erasing complete all as specified. |
| 98 | Supply andfixing 0.80 mm thick galvanised corrugated mild steel sheeting, class-8 with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts and washers, ISI markedin roofs, walls etc. with grade of zink coating 275, complete all as specified and directed. |
| 99 | Supply and fixing,Metal suspended ceiling system OREO GI laid in plain 600X600X0.50 mm (tegular) edge tiles in global white colour to be laid on strong 24mm T-section flanges colour white having rotary stitching on the main runner with web height of 38mm. Note:(i) To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit at 1200mm maximum centre.The first/last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200x600 mm mould.Cut cross tees longer than 600mm require independent support. 600X600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm,secured to walls at 450mm maximum centres. (ii) Suspension system accessories consisting of HLC sleeve anchor fasterners of thread size 6.50 mmx25/5 with soffit cleat made of galvanised steel of size 27x37x25x1.60mMaterial and Labourevel clip in dimensions of 85x30x0.80 mm with 4mm GI wire complete all as specified & directed.Note : Contractor shall produced voucher andmanufacture test certificateto Engineer-in-charge before claiming of payment. |
| 100 | Material and labour for preparation of old painted woodsurfaces of any descriptionn exe 10cm width or girth and applying one coat of synthetic enamel paint complete, all as specified and as directed by the Engineer-in-Charge. |
| 101 | Supply and fixing Steel windows with side hung shutterswith glazing bars, dovetailed or welded including projecting type hinges with steel handle, and steel peg stay complete all as specified. |
| 102 | Supply andfixing300 mmaluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed. |
| 103 | Supply andfixing aluminum handle, cast type, anodized 150mm long, complete all as specified and directed. |
| 104 | Amount of credit of Rs. 128530.00 for retrived old material as mentioned in Schedule \"A\" section-II of tender document in pdf form, will be deducted offline while acceptence of tender. |
AI Tender Summary
Tender Timeline
May 16, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedJun 07, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 09, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender