Tender For The last remaining work of beautification of Saubhari Rishi water body near Saubhari Rishi temple in village Sunrakh, district Mathura - Earth work in excavation in foundation in ordinary soil (loam, clay, or sand) including lift upto 1.5 m and lead up to 30 m and including filling watering ramming of excavated earth in to the trenches or in to the space between the building and the sides of the foundation trenches or into the space between the building and the side of the foundation or in the plinth and removal of surplus earth as directed by E/I upto a distance of 30m.from the foundation trenches 0.0m-1.50m 2 Provides & laying cement concrete in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) & curing complete, including cost of form work in foundation and under floors. 3 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) 4 Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 (GSB) 5 Laying of precast Interlocking tiles of required thickness(Compressive strength not less then 30Mpa and weight 4.50kg) Including 25mm thick local sand base levelling and dressing of surface to required level and slope, filling joints with local sand as per design approved by Architect or Engineer-in-charge all complete work.(rubber mould) 80mm thick 50% Coloured Rubber Molded Tile 6 50% Grey Rubber Molded Tile 7 Providing and laying at or near ground level factory made kerb stone of M-20 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge. (Precast C.C. kerb stone shall be approved by Engineer-in-charge).Kerb Stone Size 12 X 18 X 6 8 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level 9 Reinforcement of Reinforced concrete or reinforced brick work brought to required shape as necessary including bending for proper completion of the work and including the supply of steel and its waistage Bend, hooks, Binding wire and authorized over lapping shall be measured upto floor two level etc complete as per MoRT&H Specifications 12.40 (1600) as per Analysis (Make - Tata, Jindal, SAIL) 10 Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 400mm Dia Piles with Single Bulb Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used . 11 Class-150 (non Modular) brick workbut in in1:4 cement and coarse sand mortar super structure above plinth level upto floor five level (upto five stories) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cm. 12 Red Sand Stone work for wall lining etc. (Veneer work) 30mm thick in cement mortar 1:3 (cement:coarse sand) includingcamping jointing in white cement mortar 1:2 (white cement:stone dust)with an admixtureof pigment matching the stone shade 13 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand)with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. As per Bansiphadpur / Dholpur Pink complete as per direction of Engineer in-charge. 14 Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. 15 Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete Wedge expansion type Fastener with threaded dia 12 mm 16 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. (MARBLE/STONE WORK) 17 Mild steel or iron work in heavy sizes such as trusses, built up gates record rack, roof work gates etc, brought to required form including drilling holes, riveting or welding where necessary, and also including supply of steel bolts, nuts, wastage etc, and their fixing require for proper completion of work. 18 Painting two coat over priming coaton Steel and other metal surfaces up to 10 cm width or girth or small articles not exceeding 0.10 sq.m in area with superior synthetic enamel suchas luxol-3, Hi-gloss, apcolite, Superior, Duplex specified brushing to give an even shade and including cleaning the srface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all material, labor, tools and plants etc, required or proper completion of the work. 19 Extra for stone work ashlar sunk or moulded in cornices. 20 S/F making of Bansi paharpur Red Sand Stone garden gazebo 18*9*10 Height with 40mm thick flooring and 40mm thick roof stone including finishing with silicon polsih including all material labour T&P etc. complete as per directed by E/I. 21 Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding). For horizontal surface one coat @1.10 kg per Sqmt. MVDA Approved Rate 22 Providing & Laying Stone Chattri with column size 2.0x2.0x2.25m Height for Guard Room all complete as per design approved by Site-in-charge/ArchitectAnalysis No. 33, As per Sanction in Raskhan 23 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. 24 Providing and fixing of stone bench 25 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Analysis 26 Providing & laying P.C.C. in 1:2:4 in cement, coarse sand & 20mm guage approved stone grit including supply of all material, labour, etc required for proper completion of the work. 27 Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment) 28 Supplying and stacking sludge at site including royalty and carriage upto 5 km complete (sludge measured in stacks will be reduced by 8% for payment). 29 Cutting of Hedge/Edge including removing of cut material, cleaning, hoeing of hedge/edge bed watering, manureing and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. 30 Providing and wartering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge. 31 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)Trees Plant 32 Shrubs Plant 33 Pruning, trimming, shaping of trees /shrubs (ht 15 feet and above) i/c removal of cut materials upto 50mt. Lead, as per direction of officer in charge. T&P shall be arranged by the contractor. 34 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : HOLES 45CM DEEP, 45 CM DIA 35 Anti termite treatment by digging pits 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge. 36 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep 37 Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge. 38 Terminalia arjuna of plants height 150-165 cm. in big polybags of plants size 25 cm. DSR 2018 It No. 10343 39 Supply and stacking of Eugenia jambolana (Jamun) plant of height 150- 165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. DSR 2018 It No. 7.83 40 Nauclea cadamba (Kadam) of plants height 150-165 cm. in big poly bag of plants size 25 cm. DSR 2018 It No. 10315 41 Provind and laying selection no.1 grass turf with earthy 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and maintainenece for 30 days or more till the grass established prpoperly. DSR 2018 2.33