Annual Maintenance, Repairs and other emergent works of various water supply schemes falling in the area of Block Matchil of Sub-Division Kupwarafor the year 2025-26-- 1 Earth work in excavation by manual means in trenches for foundations, drains,pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspitsand the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: 1 meter from cutting edge 2 In all kinds of soils 3 Ordinary rock 4 Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) includingdisposal of excavated earth lead upto 50meters and lift upto 1.5 m,as directed by Engineer-in-Charge. 5 In all kinds of soils 6 Ordinary rock 7 Hard Rock (Requiring Blasting ) 8 Hard Rock (Blasting Prohibited) 9 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: 10 In all kinds of soils 11 Ordinary rock 12 Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earthlead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. 13 In all kinds of soils 14 Ordinary rock 15 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil. 16 Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. 17 Beyond 30 cm girth upto and including 60 cm girth. 18 Beyond 60 cm girth upto and including 120 cm girth. 19 Beyond 120 cm girth upto and including 240 cm girth. 20 Above 240 cm girth 21 Providing & fixing upto floor five level precast cement concrete hollow blocks, including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete. 22 1:1½:3(1 cement :1½ coarse sand :3 graded stone aggregate 20 mmnominal size) 23 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) 24 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size) 25 Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement) 26 Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 (1 cement: 3 fine sand) including curing. 27 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : 28 Cement mortar 1:6 ( 1 cement : 6 coarse sand) 29 Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: 30 Cement mortar 1:6 (1 Cement : 6 coarse sand) nallah 31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 32 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): 33 Second class kail 34 Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete 35 First class Budloo/Fir wood 36 Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete. 37 With 2nd class teak wood beading 62x19 mm 38 Providing and fixing specified board medium density exterior grade (Grade I) to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) : 39 Flat pressed 3 layer particle board or graded wood particle board IS:3087 18 mm 40 Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : 41 Second class Kail wood 42 Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work. 43 100 mmand 150 mm dia GI pipes 44 65 mm and 80 mm dia GI pipes 45 40 mm and 50 mmdia GI pipes 46 25 mm and 32 mm dia GI pipes 47 15 mm and 20 mm dia GI pipes 48 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating eachdeposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. 49 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge : 50 Above 40 mm nominal bore 51 15 - 40 mm nominal bore 52 Laying in position centrifugally cast (spun) iron S&S or flanged pipes (excluding cost of pipe) 53 Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket. 54 100 mm dia pipes 55 125 mm dia pipes 56 150 mm dia pipes 57 200 mm dia pipes 58 250 mm dia pipes 59 300 mm dia pipes 60 Dismantling of spindle / rod and check nuts of flanged type sluice valves by way of manufacturing of new spindle / rod made out of mild steel & new check nut made out of gun metal material. The job includes dismantling of sluice valve reassembling after fixing of spindle & check nut duly manufactures and threaded in workshop including cost of welding, packing, carriage to & fro upto the workshop and back to site of work (Complete job) from 100 mm dia sluice valve upto 300 mm dia sluice valve including cost of salvaged material. 61 Decamping of main cable at Filtration Plants from LT poles, cutting of main cable by Hexa blades, providing / fixing of bone china insulators, thimbles, cost of PVC tape rolls, fuse wire, engagement of skilled/ non skilled labours, cost of rope, hire charges of long stair etc.complete job 62 Providing / fixing of M.S double collers/ arresting of leakagesby way of weldingincluding all sorts of carriages 63 80 mm dia 64 100 mm dia 65 150 mm dia 66 200 mm dia 67 Providing / fixing of double collers, G.I./ M.S. for arresting of leakages by using led & spun yarn incld. earthwork excavation, refilling etc. including all sorts of carriages (length verying from 0.60 to 1 Mtr.) 68 40 mm dia 69 50 mm dia 70 65 mm dia 71 80 mm dia 72 100 mm dia 73 150 mm dia 74 200 mm dia 75 Providing and fixing including testing, commissioning & fabricating at site M.S pipe Specials Etc. & all sorts of carriages upto site of work, as per requirement at site complete job. 76 Providing and fixing of Electrical points (heating and lighting) incld. cost of wire switches, necessary MCB’s switch boards, ceiling roses reputed make ISI mark screws, casing / conduit materials of allsorts of carriage and labour charges required for the job. 77 Lighting points 78 Heating points 79 Supply/ fixing of pipe specials from open market, if not available in the Divisional stores of ISI marked standard make. 80 100 mm dia G.IUnion 81 80 mm dia G.IUnion 82 65 mm dia G.I. Union 83 50 mm dia G.I. Union 84 40 mm dia G.I. Union 85 25 mm dia G.I. Union 86 20 mm dia G.I. Union 87 80 mm dia G.I. Elbow 88 65 mm dia G.I. Elbow 89 50 mm dia G.I. Elbow 90 40 mm dia G.I. Elbow 91 25 mm dia G.I. Elbow 92 20 mm dia G.I. Elbow 93 80 mm dia G.I. Socket 94 65 mm dia G.I. Socket 95 50 mm dia G.I. Socket 96 40 mm dia G.I. Socket 97 25 mm dia G.I. Socket 98 20 mm dia G.I. Socket 99 80 mm dia G.I. Nipple upto 10 100 65 mm dia G.I. Nipple upto 10 101 50 mm dia G.I. Nipple upto 10 102 40 mm dia G.I. Nipple upto 10 103 25 mm dia G.I. Nipple upto 10 104 20 mm dia G.I. Nipple upto 10 105 15 mm dia G.I. Nipple upto 10 106 25x25x20 mm dia G.I. Equal Tee 107 40x40x25 mm dia G.I. Equal Tee 108 50x50x40 mm dia G.I. Equal Tee 109 65x65x50 mm dia G.I. Equal Tee 110 80x80x65 mm dia G.I. Equal Tee 111 25x20 mm dia Socket/ Reducer 112 40x25 mm dia Socket/ Reducer 113 50x40 mm dia Socket/ Reducer 114 65x50 mm dia Socket/ Reducer 115 80x65 mm dia Socket/ Reducer 116 25x20 mm dia Elbow/ Reducer 117 40x25 mm dia Elbow/ Reducer 118 50x40 mm dia Elbow/ Reducer 119 65x50 mm dia Elbow/ Reducer 120 80x65 mm dia Elbow/ Reducer 121 100mm dia Elbow 122 100mm dia Equal Tee 123 100 mm dia G.I. Bend 124 80 mm dia G.I. Bend 125 65 mm dia G.I. Bend 126 50 mm dia G.I. Bend 127 40 mm dia G.I. Bend 128 Supply of Kerosene 129 Re-threading of damaged pipe ends including carriage from site to workshop and back. 130 20 mm dia 131 25 mm dia 132 40 mm dia 133 50 mm dia 134 65 mm dia 135 80 mm dia 136 100 mm dia 137 Dismentalling of backwash motors/ Alum motors/ bleaching motors of filtration plants by way of rewinding of core made out of copper metal fiber superior type of required thickness and guage. The job includes replacing of bearings, water seal, nuts, bolts, rubber washers and painting of instruments. The job also includes all sorts of carriage from site to work upto workshop to & fro including testing & commissioning of following capacity. 138 For 0.50 HP to 2.00 HP 139 For 3.00 HP to 5.00 HP 140 For 5.00 HP to 10.00 HP 141 Dismentalling of complete reduction gear unit of de-sludge bridges for repairs by way of providing & manufacuring of complete reduction gear with hub. The job includes costing of brass material, grinding & finishing of virme in order to make the new teeth, replacement of damaged oil seals by way of new one, replacemnet of ball bearings, pouring of required specific gravity ear oil in order to run the reduction gear in smooth order, refixing of same at the site of work incld. all sorts of carriage fro site of work upto workshop and back to site of work including testing & successful commissioning (complete job) 142 Hire charges of vehicle alongwith comercial driver licensed for Supervision of Works/ attending Workshops/meetings etc. 143 From 0 - 10 kms 144 From 10 to 20 kms 145 From 20 to 30 kms 146 From 30 to 45 kms 147 From 45 to 60 kms 148 beyond 60 kms 149 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 150 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 151 White washing with lime to give an even shade on Old Work (two or more coats) 152 Colour washing such as green blue or buff to give an even shade 153 New work (two or more coats) with a basecoat of white washing with lime. 154 New work (two or more coats) with basecoat of whiting 155 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer 156 Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre, two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications 157 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. 158 Finishing walls with water proofing cement paint of required shade: Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete including cost of priming coat. 159 Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 160 Applying priming coat: With ready mixed aluminum primer of approved brand and manufacture on resinous wood and ply wood 161 Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works 162 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work 163 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 164 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete. On steel work 165 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete. On concrete work 166 Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work 167 With ready mixed pink or grey primer on wood work (hard and soft wood) havingVOC content less than 50 grams/ liter 168 With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter 169 Overhauling voltage stabilizers installed at site. The job includes pouring / filling of transformer oil of required specified gravity, replacement of driven rotars (automatic), replacement of voltage meters, Amp meters, indicators, thimbles etc. complete job, making the unit complete functional for bearing of required load. The job also includes labour charges, cost of wiring, pin sockets and all sorts of carriages from site of work upto the workshop & back to actual site of work incld. installation at site & testing, successful commissioning complete job. 170 5 KV to 10 KV 171 11 KV to 20 KV 172 21 KV to 30 KV 173 Providing and fitting at site 3-phase, Voltage stabilizer 30 KVA of following ratings, oil emersed, of standard make and quality including accessories as required. The job includes making of connections with main panel board and service line. To be paid in fitted and finished form after testing on full load capacity, complete job. 174 Providing and fitting at site 3-phase, Voltage stabilizer 25 KVA of following ratings, oil emersed, of standard make and quality including accessories as required. The job includes making of connections with main panel board and service line. To be paid in fitted and finished form after testing on full load capacity, complete job. 175 Supply and filling of filter media from approved source - Gravel (Graded gravel - size ranging from 2.0mm to 40.00 mm) in filter beds. Including all carriages, complete job 176 Supply and filling of filter media from approved source - Sand (Coarse filter sand - in filter beds. Including all carriages, complete job 177 Flooring with marble stone of specified thickness as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including skirting in vertical, rubbing, polishing and curing complete with: Makrana White Second quality (16mm) 178 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters: 80x1.25 mm M.S. laths with 1.25 mm thick top cover 179 80x1.25 mm M.S. laths with 1.25 mm thick top cover 180 80x1.20 mm M.S. laths with 1.20 mm thick top cover 181 80x0.90 mm M.S. laths with 0.90 mm thick top cov 182 Providing and fixing ball bearing for rolling shutters. 183 Bore Packing: All the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout - GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pipe and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent. 184 Desilting of various structures incld. Disposal of desilted material from site premises with all carriages lead & lifts etc. The job also includes, washing and cleaning of walls, beds, drains and floor etc with bleaching powder solution complete job. 185 Using buckets, ropes etc. Manually 186 Through washout by Mix silt with water 187 Making connection of G.I. distribution branch with G.I. main offollowing sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 188 Upto 40mm Nominal Bore 189 Above 40mm Nominal Bore 190 Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. 191 Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix) 192 Demolishing RCC work manually by mechanical means including stacking of steel bars and disposalof unserviceable material within 50 meters lead as per direction of Engineer-incharge 193 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 194 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 195 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) 196 Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and strutsupto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 197 Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 198 Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 gradedstone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate. 199 Replacement / supply of PVC gate valves for bleaching / alum tanks/ Foot valves and PVC pipes of ISI marked standard make 200 20 mm dia Gate valve 201 25 mm dia Gate valve 202 32 mm dia Gate valve 203 40 mm dia Gate valve 204 50 mm dia Gate valve 205 20 mm dia PVC pipe (B-class) 206 25 mm dia PVC pipe (B-class) 207 32 mm dia PVC pipe (B-class) 208 40 mm dia PVC pipe (B-class) 209 50 mm dia PVC pipe (B-class) 210 80 mm dia PVC pipe (B-class) 211 100 mm dia PVC pipe (B-class) 212 Replacement of old damaged G.I. Gate valves by providing / fixing of new Gate valves including cost of nuts, bolts, rubber insulations of ISI marked standard make all carriages upto site of works, complete and providing of check certificate from the standard manufacturer. 213 100 mm dia Gate valve 214 80 mm dia Gate valve 215 65 mm dia Gate valve 216 50 mm dia Gate valve 217 40 mm dia Gate valve 218 25 mm dia Gate valve 219 20 mm dia Gate valve 220 Providing / fixing of newDI/CI Sluice valve including cost of nuts, bolts, rubber insulations, flanges and welding incl tail pieces etc of ISI marked (Kirlosker/Vage or equalivent made)incl all carriages upto site of works, complete . and providing of check certificate from the standard manufacturer 221 350 mm dia Sluice valve 222 250 mm dia Sluice valve 223 200 mm dia Sluice valve 224 150 mm dia Sluice valve 225 100 mm dia Sluice valve 226 80 mm dia Sluice valve 227 65 mm dia Sluice valve 228 50 mm dia Sluice valve 229 Supply of CFL Bulbs for filtration plant sites etc. 230 20W CFL 231 15W CFL 232 12W CFL 233 9W CFL 234 Welding, including transportation of plant at site etc. complete 235 By gas plant 236 By electric plant 237 Carriage of material from divisional store up to dumping site of work, including loading, unloading and stacking etc. complete by Mechanical Transport 238 Cement & steel, G.I/C.I pipe avg. lead upto 01 Kms 239 Cement & steel, G.I/C.I pipe avg. lead upto 02 Kms 240 Cement & steel, G.I/C.I pipe avg. lead upto 03Kms 241 Cement & steel, G.I/C.I pipe avg. lead upto 04 Kms 242 Cement & steel, G.I/C.I pipe avg. lead upto 05 Kms 243 Cement & steel, G.I/C.I pipe avg. lead beyond 5 Kms upto 10 Kms (per Km) 244 Cement & steel, G.I/C.I pipe avg. lead beyond 10 Kms upto 20 Kms (per Km) 245 Cement & steel, G.I/C.I pipe avg. lead beyond 20 Kms per additional Km 246 Sand & Agg. 20 mm avg. lead of upto 01 Kms 247 Sand & Agg. 20 mm avg. lead upto 02 Kms 248 Sand & Agg. 20 mm avg. lead upto 03Kms 249 Sand & Agg. 20 mm avg. lead upto 04Kms 250 Sand & Agg. 20 mm avg. lead upto 05Kms 251 Sand & Agg. 20 mm avg. lead beyond 5 Kms upto 10 Kms (per Km) 252 Sand & Agg. 20 mm avg. lead beyond 10 Kms upto 20 Kms (per Km) 253 Sand & Agg. 20 mm avg. lead beyond 20 Kms per additional Km 254 40 mm Agg. avg. lead of upto 01 Km 255 40 mm Agg. avg. lead upto 2 Kms 256 40 mm Agg. avg. lead upto 3 Kms 257 40 mm Agg. avg. lead upto 4 Kms 258 40 mm Agg. avg. lead upto 5 Kms 259 40 mm Agg. avg. lead beyond 05 Kms upto 10 Kms (per Km) 260 40 mm Agg. avg. lead beyond 10 Kms upto 20 Kms (per Km) 261 40 mm Agg. avg. lead beyond 20 Kms per additional Km 262 Stone soiling avg. lead of upto 1 Km 263 Stone soiling avg. lead upto 2 Kms 264 Stone soiling avg. lead upto 3 Kms 265 Stone soiling avg. lead upto 4 Kms 266 Stone soiling avg. lead upto 5 Kms 267 Stone soiling avg. lead beyond 05 Kms upto 10 Kms (per Km) 268 Stone soiling avg. lead beyond 10 Kms upto 20 Kms (per Km) 269 Stone soiling avg. lead beyond 20 Kms per additional Km 270 Carriage of pipes from divisional store up to dumping site of work, including loading, unloading and stacking etc. complete by Mechanical Transport 271 100 mm and 125 mm dia DI/ GI pipes 1Km 272 100 mm and 125 mm dia DI/ GI pipes 2Km 273 100 mm and 125 mm dia DI/ GI pipes 3Km 274 100 mm and 125 mm dia DI/ GI pipes 4Km 275 100 mm and 125 mm dia DI/ GI pipes 5Km to 10 Km 276 100 mm and 125 mm dia DI/ GI pipes 10Km to 20 Km 277 100 mm and 125 mm dia DI/ GI pipes beyond 20 Km every additional lead 278 150 mm to 200 mmdia DI pipes 1 Km 279 150 mm to 200 mmdia DI pipes 2 Km 280 150 mm to 200 mmdia DI pipes 3 Km 281 150 mm to 200 mmdia DI pipes 4 Km 282 151 mm to 200 mmdia DI pipes 5 Km 283 150 mm to 200 mmdia DI pipes 5Km to 10Km 284 150 mm to 200 mmdia DI pipes 10Km to 20Km 285 150 mm to 200 mmdia DI pipes beyond 20Km for every additional lead 286 Centering and shuttering including strutting, propping etc, and removal of form for. 287 Foundations, footings, bases of columns etc for mass concrete. 288 Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. 289 Columns, pillars, piers, abutments, posts and struts. 290 Suspended floors, roofs, landings, balconies and access platforms. 291 Lintel, beams, plinth beams, girders, bressumers and cantilevers. 292 Stairs (excluding landings) except spiral staircases. 293 Edges of slabs and breaks in floors and walls under 20cm wide 294 Extra for shuttering in circular work (20% of respective centring and strutting items) 295 Clearing snow (with frost) from roads, manually using picks and shovels; snow depth upto 150 mm 296 Clearing snow avalanche mixed with frost and compressed snow, including all types of equipments and safety to the workers while clearing the avalanches at head site 297 Supply of fire wood / rejection wood incld. all carriages upto site of work, complete 298 Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with:Cement mortar 1:6 (1 Cement : 6 coarse sand) Quarry 299 Dry random rubble masonry with hard stone in foundation and plinth: With bond stone. (Nallah) 300 Providing / fixing of M.S. step collers from 100 mm to 450 mm dia including all sorts of carriages, complete 301 Renewing glass panes and re-fixing existing wooden fillets: Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm) 302 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 303 Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded 304 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 305 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. 306 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 307 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 308 M.S. tube 309 E.R.W. tubes 310 G.I. pipes 311 Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete. 312 Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides 313 Stainless steel (grade 304) wire gauze of 0.5mm dia wire and 1.4 mm aperture on both sides. 314 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. 315 In colour such as White, Ivory, Grey, Fume Red Brown 316 In all colours, shades, except White, Ivory, Fume Red Brown 317 Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.50 mm thick with zinc coating not less than 275 gram/m2 318 Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 319 1.00 mm thick with zinc coating not less than 275 gram/m2 320 Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2 321 Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 322 75 mm diametre 323 110 mm diametre 324 12mm Cement plaster finished with a floating coat of neat cement of mix: 325 1 : 3 ( 1 cement : 3 fine sand) 326 1 : 4 ( 1 cement : 4 fine sand) 327 Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm) 328 Renewing glass panes, with wooden fillets wherever necessary : 329 Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm) 330 Cleaning of under ground sump, Over Head R.C.C. Tank (independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of silt and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge 331 Providing and Laying of Stone Soling Hand Packed and compacted manually including all carriages complete 332 Good Earth 333 Moorum 334 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. 335 Made of G.I. wire of dia 4 mm 336 Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). 16.67.1 Overhead informatory road signage. 337 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 338 Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 339 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 340 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc. if required will be paid separately). 341 50 mm dia 342 80 mm dia. 343 100 mm dia. 344 Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) 345 80 mm dia. nominal bore 346 100 mm dia. nominal bore 347 150 mm dia. nominal bore 348 200 mm dia. nominal bore 349 Providing and laying D.I. Specials of Class K-12 suitable for push-on jointing as per IS : 9523 350 Upto 600 mm dia. 351 Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. One coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge. 352 Weed clearance 353 From lakes(using boats) 354 From canals/Springs(including extraction of roots) 355 Powder coated aluminum (minimum thickness of powder coated 50 microns) 356 Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns) 357 Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. 358 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. 359 Pre-laminated particle board with decorative lamination on both sides 360 Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic items) 361 With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm) 362 With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm) 363 With float glass panes of 8 mm thickness (weight not less than 20.0 kg / sqm) 364 Supply and fixing of Inaugration stone with custom carved letters complete including Making of Foundationmade out of Brick work including 15mm thick Plater in 1:4 Mix including all sorts of carriages wherever required 365 Providing and fixing of printed PVC type flex banners as per requirement complete job 366 Without the supporting frame of steel rolled hollow Sq. bars 367 With the supporting frame of steel rolled hollow Sq. bars 368 With the supporting frame of steel rolled hollow Sq. bars and cardboard backing 369 Supply of unskilled labours 370 Supply of skilled labour 371 Supply of Carpenter 2nd class 372 Supply of Mason 2nd class 373 Providing / Fixed of GI barbed wire weight 9.3 Kg per 100m (min) between two ports fitted and fixed with GI staples on wooden plugs or GI binding wire tied to 6mm bar nibs, Complete Job 374 Repairs to barbed wire fencing, complete job 375 Providing and Fixing of M.C.C.B.of ISI marked standard make the job includes dismantling of damaged/non functional Amp. M.C.C.B. and fixing of new one including all sorts carriage from source to workshop including carriages of salvaged material from filtration plant upto Divisional Stores including testing, installing and commissioning complete job 376 03 Pole 200 Amp. 377 03 Pole 100 Amp. 378 04 Pole 100 Amp. 379 02 Pole 32 Amp. 380 03 Pole 32 Amp. 381 04 Pole 32 Amp. 382 63 Amp 04 pole change over 383 3.5 core cable 50 mm thick 384 Providing and Fixing of 5-10 H.P. Starter of of ISI marked standardMake, the job includes dismantling of damaged /non functional starter and fixing of new one incl. all sorts of carriages from source to workshop including carriages of salvaged materials from filtration plant upto Divisional Stores, including testing, installing and commissioning complete job. 385 Providing and Fixing of running V-Belt of groove type for air blower, the job includes dismantling damages ones and fixing of new ones incl. successful testing, commissioning. All types of carriage complete 386 Providing fixing & commissioning of LED Flood Lights of 50 Watts with stand including all accessories required at site complete job inclusive all carriages. 387 Providing fixing & commissioning of LED Flood Lights ofwith stand including all accessories required at site complete jobinclusive all carriages. 388 50 W 389 30W 390 20 W 391 15W 392 Supply of LED lights of different Wattage of approved m ake ISI marked complete in all respects 393 15 W 394 11 W 395 9 W 396 7 W 397 Providing fixing & commissioningof 10/12 mm thick Flanges in pairs including welding, cutting of threaded portion, washers including cost of Flanges with Nuts and Bolts including making joint leak proof including all sorts of labours whatsoever required 398 250mm dia 399 200mm dia 400 150mm dia 401 100mm dia 402 80mm dia 403 65mm dia 404 Restoration of damaged pipes due to frost / frozen including earth works excavation /dismantling /refilling /making good the samecomplete job in all respects. Upto 20mmto 100mm dia (by using blue lamp including cost of K.oil) 405 P/F of Air Releasing Valves (single acting) including cutting of bore hole , welding of the pedestal rod and providing laying of cement concrete 1:3:6 mix with shuttering box PGI 9”X9”x12” around the pedestal rod with all carriages and head load upto actual site of work 406 25mm dia Air Valve 407 20mm dia Air Valve 408 Laying& fixingof HDPE Pipes complete excluding earth work, but including all carriages upto site of work 409 25mm dia 410 32mm dia 411 40mm dia 412 50mm dia 413 Fixing charges of Sluice Valves including Testing, Commissioning and carriages from divisional store to actual site of work including dismantling of old (in case of replacement) and carriage of same to divisional store, Complete job 414 200 mm dia 415 150 mm dia 416 100mm dia 417 80mm dia 418 50mm dia 419 Engagement of JCB including haltage charges and one side POL Charges 420 Removal of dead animals fromcanals including disposal within 50 mts complete job 421 By Mechanical means 422 By Mannual means 423 Constructing muthu bunds, comprising boulders and wood bushes in alternate layers; including working in water situations 424 Supplying and Laying of polythene sheets (Black) at off take points during lean dscharge / Freezing 425 Opening out old wire crates those and re-binding after filling. 426 Filling empty cement bags with sand/ earth including cost of bags and earth / sand (Earth or sand to be locally excavated) including all sorts of carriages upto actual site of work 427 Siltclearance from canalsInclusive of initial lead of 50 mts and all lift Comp Job 428 Providing necessary complete personnel protective clothing kitincluding Jackets and shoes to the PHE Staff during severe conditions 429 Jackets With PHE Tagging 430 Long Shoes for under water works 431 Helmets / Gloves 432 Water Proof rain Coats 433 Removing, washing of old filter media including washing of filter beds and laying of same in position complete job. 434 Supplying & fixing as per site requirement of Nylon rope on 10 mm dia of Standartd make including all carriages comp job 435 Hire charges of boat including charges of operator and other allied items required, complete. 436 Small Boat 437 Big Boat(Shikara) 438 Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like. 439 Providing / fixing of slip ring complete set with cliffs, bushes all accessories for clarifloculator bridge. The job includes disassembling of the damaged slipring returned back to store and fixing of new one, including all carriages. 440 Dismantling of C.I. sluice valve including stacking of useful materials within a lead of 50 meters. 441 Upto 150 mm diameter. 442 Above 150 mm diameter. 443 Dismantling C.I. pipes manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes and lead at site within 50 meter lead as per direction of Engineerin-charge 444 Upto 150 mm diameter. 445 Above 150 mm diaupto 300 mm dia. 446 Cutting road and making good the same including supply of extra quantities of material i.e. crushed aggregate, moorum screening, red bajri and labour required. 447 Water bound macadam. 448 Bituminous portion 449 Labour for cutting C.I. pipe with steel saw. 450 80 mm diameter C.I. pipe 451 100 mm diameter C.I. pipe 452 125 mm diameter C.I. pipe 453 150 mm diameter C.I. pipe 454 200 mm diameter C.I. pipe 455 250 mm diameter C.I. pipe 456 Hire charges for welding plant for necessary repairs of pipe network/structures etc as per requirement including C/O operator, Genrator, welding rods, wiring and carriage of man and machinary complete in all respects as per requirement at site but excluding additional materials like collar, pipe specials, steel section etc. 457 Hand-packing stones in wire-crates; excluding cost of crates and stones 458 Supply of wire crates including all types of carriages upto site of work. 459 Supply of stones including all types of carriages upto site of work. 460 Providing coloured Photographs as per requirement/ works executed at various places on photo paper of size 4X6 461 Repair of Computer Desktops/Laptops, Inktank Printers, copiers, cables etc. complete 462 Supply of Ink to Office Printer for Epson Ecotank L 3210/Canon 2012/Epson L130 including all carriages complete 463 Supply of Cartridge for HP Laserjet office printer 464 Providing Installation of tents for mela/ Necessary functions 465 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 466 Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete. 467 Repairment of monoblock motors of different capacities including dismembering, rewinding, refixing, testing, commissioning and all types of carriages complete in all respects 468 1.00 H.P 469 1.5 H.P 470 2.00 H.P 471 5.00 H.P 472 Providing of Bombai massala for prevention of leakages in pipe and pipe specials 473 Supply of Necessary Items For Operators of Plant for maintening cleanliness of Plant/ ensuring watch and ward of Plants 474 Blankets approved by Engineer In Charge 475 Curtainsof Size 7feet x4 feet approved by Engineer in Charge 476 UnbreakableBuckets of ISI Mark 477 UnbreakableMugs of ISI Mark 478 Brooms/wipers 479 Slippers/ Sandal 480 Providing completeGas Chula with Filled Gas Cylinder 481 Cup Sets of approved quality as approved by Engineer in Charge 482 Steel Plates as approved by Engineer in Charge 483 Complete Bedding Set including 4x6 Matresses Including Cover, King Size Quilt with cover, 02No Pillows with cover, Bed Sheet. 484 Providing Flower Bookies during VIP Visits, Inaugrations etc. 485 Providing of LPG Heaters 486 Measuring Tap 15.0m Tape of Approved Quality 487 Vernair Calliapir 488 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. 489 For thickness of tiles 10 mm to 25 mm 490 For thickness of tiles above 25 mm and upto 40 mm. 491 Supply and installation of Inverter with battery of standard make including all accessories for filtration Plants etc. Complete JOB 492 Documentation of various offical documents/DPRs including 493 Paper Ream 494 Spiral Binding 495 Thermal Binding 496 Supply of Spun yarn 497 Supply of Pig Lead at site of work 498 P/F of PPR pipe, including all pipe fitting, carriages upto Site of work complete in all respects 499 25 mm 500 32 mm 501 Providing of PPR Gate valves/ Ball valves including all necessary accessories as per requirement at site complete 502 25 mm Gate valve/ Ball valve 503 32 mm Gate Valve/ Ball valve 504 40 mm Gate valve/ Ball valve 505 Supply of Nallah Muck including laying of same manually/ mechanically including all sorts of carriage complete 506 Supply of stone dust including laying of same manually including all sorts of carriages complete 507 P/F of wooden pannelling work using budloo/Rat Wood including frame work made from 50x50mm wooden section of same type to prepare smooth base, c/o nails, wooden polish, all types of carriages complete in all respects. 508 Hire charges of Sumo for various anouncements regarding the water usage/registration/awarances etc including the mic, speaker, driver, fuel etc complete as per requirements and directions. 509 Supply of coloured banners using PVC/Vinyle roll including writing of description as per directions complete in all respects. 510 Providing and fixing basin mixer of approved quality. 511 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia 512 Providing and fixing CP Brass tapes of quality & make as approved by Engineer in charge. 15 mm nominal dia 513 Providing and fixing P.V.C low level flushing cistern with manually18.0 (Sanitary Installation) 240 CODE NO. DESCRIPTION UNIT RATE ₹ controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 litre capcity -white 514 Lettering with black Japan paint of approved brand and manufacture. 515 Providing of plastic buckets, Mug, Brooms, Wippers etc of good quality at various plants complete. 516 Fabrication of GI bends of required angle/size, Tees, tail pices etc at site using welding job including cutting of pipes, fixing of flunges, nuts, bolts, washers etc for Washout system. The job includes carriage of man , machinary, carriage of pipe material from departmental store upto site of work complete in all respects. Cost of flanges will be paid separately 517 80mm dia 518 100mm dia 519 150mm dia 520 Fabrication of M.S Glands/pipe specialsof required size, Tees, tail pices etc at site as per ground profile using welding job including cutting of pipes, fixing of flunges, nuts, bolts, washers etc for Washout system. The job includes cost of M.S pipe, flanges, nuts , bolts glands, R.I clothcomplete job 521 P/F of stainless steel mesh with 2,50 to 3.50mm thick mesh fixed in angle iron frame 45x45x6mm complete in all respects to cover varios SSFPS, gratings, at head sites etc as per requirement. 522 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto/above plinth level 523 Thermo-Mechanically Treated bars of grade Fe-500D or more. 524 Providing of blue lamps including all sorts of carriages complete 525 1 ltr capacity 526 0.75 ltr capacity 527 Providing/ fixing of Rubber Gaskets 528 80 mm dia 529 100 mm dia 530 150 mm dia 531 200 mm dia 532 250 mm dia 533 Providing/ fixing of Rubber Washers 534 80 mm dia 535 100 mm dia 536 150 mm dia 537 200 mm dia 538 250 mm dia 539 Packing of sluice valves from 400 mm dia to 100 mm dia including rubber washers, nut bolts etc. complete in all respects 540 Providing and fixing 1st quality ceramic glazed floor/ wall tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 541 Supply and Installation of acrylic Boards 5 mm thick with laser cut etc. complete Job 542 Supply of cast iron general purpose pipe wrenches of Stilson type as per IS: 4003(Part-I) - 1978 inclusive of all taxes and carriages. 543 Size 10 inch, length 250 mm suitable for pipe dia upto 32 mm 544 Size 300 mm, Length 12.5 inchupto 40 mm dia 545 Size 350 mm, Length 14 inchupto 50 mm 546 Size 450 mm, Length 18 inchupto 65 mm 547 Size 600 mm, Length 24 inchupto 80 mm 548 Supply of high grade carbon steel chain pipe wrenches as per IS: 4123 - 1982/95inclusive of all taxes and carriages 549 Chain length 900 mm for pipe dia upto 100 mm 550 Chain length 1000 mm for pipe dia upto 150 mm 551 Supply of steel ratched die sets inculsive of all taxes and carriages (Taparya/ Inder make or equivalent) 552 for pipe dia 1/2,3/4 and 1 inch 553 for pipe dia 1_1/2 and 2 inch 554 Providing of Hammer 1 kg weight with handle 555 Providing of Hammer 1.5 kg weight with handle 556 Providing of Pick Axe with handle 557 Hire and installation charges of Shamyana’s of good quality/shape/colour/hygiene (as per the directions of Engineer In-charge) for VIP’s, Guests, Officers, School Children etc with all leads, lifts, handing, rehandling and carriage upto site and lifting back after conclusion of ceremony. 558 Hire charges for supply of furnishing/furniture items of good quality/shape/colour/hygiene (as per the directions of Engineer In-charge) of required size with all leads, lifts and carriage including fixing of the same in arranged manner as will be directed at site all complete 559 VIP Chairs 560 P.V.C Chairs (heavy duty) 561 Druggets (12’x12’) 562 Carpets (12’x12’) 563 Red Runners of required width 564 Hire and installation charges of Pindals having size (50’-0’x150’-0”) for four days fixed with G.I tube with water proofing top and sides white house ornamental celling with crewel lining of required size for VIP’s, civil and police officers of district administration distinguished guests, panches and surpanches and other designates to grace the occasion (it should be of good quality, shape , colour, hygiene as per the Directions of Engineer In-charge) 565 Preparation and making arrangements of Zaffron, Kehwa with Shrmal ready to serve with all crockery items like cups, spoons and plates etc of Superior quality free from cracks etc incl, supplying of medium size Shirmal of good quality to be obtained from Standard baker complete. 566 Supplying and serving of Fresh Mixed Dry Fruit incl. serving in bowls and hire charges of the same. 567 Supply and fixing of Banners of required sizes with required letter writing as directed size (3’x6’) complete 568 Hire and installation charges of view cutter canath 7’-0’ including to fixing for covering of the area around venue and removal of same after conclusion of the function as per the directions of Engineer incharge complete. 569 Hire charges for standard Air Cooler for VIP’s incl. all carriage etc complete. 570 Hire Charges Of loudSpeakers for necessary announcements 571 Making holes to the R.C.C walls, the job includes making of hole of required size as per site requirement and making it good leakproof after fixing pipe etc., complete job 572 carriage of chemicals viz Alum, Bleaching Powder from divisional Store upto dumping site of work, including loading, unloading and stacking etc. Complete by Mechanical Transport 573 Engagement of water tanker service (subject to the approval from this office) with minimum 4 trips per day or as per requirement incld. Hire charges of tanker with capacity of minimum 8000 litres including driver and POL/HSD charges 574 Engagement of dewatering pump for arresting leakages including cost of fuel/ hire charges of pump andall carriages upto site of work complete 575 Engagment of 125/150mm desluge motor along with Generator for desilting of dug wells raw water sumps etc incl all charges of operator of fuel all carriages complete job 576 Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) 577 15 mm dia. nominal bore 578 20 mm dia. nominal bore 579 25 mm dia. nominal bore 580 32 mm dia. nominal bore 581 40 mm dia. nominal bore 582 50 mm dia. nominal bore 583 65 mm dia. nominal bore 584 80 mm dia. nominal bore 585 100 mm dia. nominal bore 586 Providing stabilizer oil 587 Lightenning/decoration for 15 Aug and 26 Jan 588 Fixing of 125mm Sluice Valave as directed by Site Engineer Complete job 589 Hire charges of dewatering pumping moter/sludge pump 40/65/80mm Dia for bailing out water from trenches etc incl. fuel charges, operational) charges to and fro complete job
