|
| 1 | SUPPLY OF C.I/C.S/G.M. Casting Items |
| 2 | C.I. Items such as bush, rod, hollow, drum, square etc as per drg. Rough machine |
| 3 | -Do- Supply Basis |
| 4 | -Do- Conversion Basis |
| 5 | G.M. Items such as bush, rod, hollow, drum,square etc as per drg. Rough machine |
| 6 | -Do- Supply Basis |
| 7 | -Do- Conversion Basis |
| 8 | G.M. bearing of side roller, top roller, bottom roller, transmissiongear etc. as per drg. Dully machined in 85:5:5:5 ratio |
| 9 | -Do- Supply Basis |
| 10 | -Do- Conversion Basis |
| 11 | C.I. wheel for lime slakar as per drg. & ETP Clarifier as per drg |
| 12 | -Do- Supply Basis |
| 13 | -Do- Conversion Basis |
| 14 | C.I. drum coupling as per drg. 8\"& below |
| 15 | -Do- Supply Basis |
| 16 | -Do- Conversion Basis |
| 17 | C.I. drum coupling as per drg. 10\"& above |
| 18 | -Do- Supply Basis |
| 19 | -Do- Conversion Basis |
| 20 | C.I. scraper as per drg. No.KSCMS/MH-15R1 rough machine |
| 21 | -Do- Supply Basis |
| 22 | -Do- Conversion Basis |
| 23 | C.I. Nozzleas per drg. |
| 24 | -Do- Supply Basis |
| 25 | -Do- Conversion Basis |
| 26 | C.I. boiler ash plate for gratebar as per drg. |
| 27 | -Do- Supply Basis |
| 28 | -Do- Conversion Basis |
| 29 | C. lever for boiler as per sample: |
| 30 | -Do- Supply Basis |
| 31 | -Do- Conversion Basis |
| 32 | Repairing/Replacement of hy.cap liner (after repairing/replacement of liner hy.Tested of the pressure 4500 LBS/02 & polishing of R/M 85:5:5:5 completion (G.M) |
| 33 | -Do- Supply Basis |
| 34 | -Do- Conversion Basis |
| 35 | C.I. mouth piece for boiler as per drg. |
| 36 | -Do- Supply Basis |
| 37 | -Do- Conversion Basis |
| 38 | C.I. \"V\" belt pully (machined) with pilot bore per 10 mm OD per groove. |
| 39 | -Do- Supply Basis |
| 40 | -Do- Conversion Basis |
| 41 | C.I. boiler door (Machinned) as per drg/sample |
| 42 | -Do- Supply Basis |
| 43 | -Do- Conversion Basis |
| 44 | Axle for tie rod crank as per drg. |
| 45 | -Do- Supply Basis |
| 46 | -Do- Conversion Basis |
| 47 | C.I. worm wheel 72 teeth |
| 48 | -Do- Supply Basis |
| 49 | -Do- Conversion Basis |
| 50 | C.I worm wheel 65 teeth |
| 51 | -Do- Supply Basis |
| 52 | -Do- Conversion Basis |
| 53 | C.I flate coupling (different size per 10mm OD with pilot bore |
| 54 | -Do- Supply Basis |
| 55 | -Do- Conversion Basis |
| 56 | C.S. Pick Off Gear (Spur) - Nos. of Teeth - 42, Module - 1.75 |
| 57 | -Do- - Nos. of Teeth - 72, Module - 1.75 |
| 58 | -Do- - Nos. of Teeth - 84, Module - 1.75 |
| 59 | New Supply Basis CS/EN-9 worm Wheel for 40:1- Ratio R.G. Box |
| 60 | New Supply Basis GM worm Wheel for 40:1- Ratio R.G. Box |
| 61 | Replacement of GM linner for Mill Hydraulic Cap |
| 62 | C.S. Trash Beam as per Drg. KSCMS/MH-96-93-2002 On Supply Basis |
| 63 | C.S. Trash Beam as per Drg. KSCMS/MH-96-93-2002 On Conversion Basis |
| 64 | C.S. Crown Pinion On Supply Basis |
| 65 | C.S. Crown Pinion On Conversion Basis |
| 66 | C.S. Base Plate of BearingHousing as per drg. On Conversion Basis |
| 67 | C.S. Base Plate of BearingHousing as per drg. On Supply Basis |
| 68 | C.S. Coupling Set as per drg. Supply Basis |
| 69 | C.S. Coupling Set as per drg. Conversion Basis |
| 70 | C.S. Trash Plate as per drg. Conversion Basis |
| 71 | C.S. Trash Plate as per drg. Supply Basis |
| 72 | C.S. Tail Bar as per drg. KSCMS/MH-694-017 Supply Basis |
| 73 | C.S. Tail Bar as per drg. KSCMS/MH-694-017 Conversion Basis |
| 74 | C.S. Rail for Cane Unloader Wheel as per drg. Supply Basis |
| 75 | C.S. Rail for Cane Unloader Wheel as per drg. Conversion Basis |
| 76 | C.S. Tei Bar for Mill Trash Plate as per drg. KSCMS/MH-43 Conversion Basis |
| 77 | C.S. Tei Bar for Mill Trash Plate as per drg. KSCMS/MH-43 Supply Basis |
| 78 | C.I Drum for Cane Unloader as per drg. KSCMS/MH- 522-2001Supply Basis |
| 79 | C.I Drum for Cane Unloader as per drg. KSCMS/MH- 522-2001Conversion Basis |
| 80 | C.SCane Unloader gear wheel- No. of Teeth 68, Module - 6, PCD- 408, Outer Dia- 420, RD- 394.1 and Pinion teeth - 18, Module- 6, PCD- 108, OD- 120,as per drg. KSCMS/MH- 404-98Supply Basis |
| 81 | C.SCane Unloader gear wheel- No. of Teeth 68, Module - 6, PCD- 408, Outer Dia- 420, RD- 394.1 and Pinion teeth - 18, Module- 6, PCD- 108, OD- 120, as per drg. KSCMS/MH- 404-98Conversion Basis |
| 82 | Spur Gear no. of Teeth - 19, M- 8, PCD-152, OD- 168, RD- 133mm, FW- 130mm as per drg. No. KSCMS/MH- 647-01Supply Basis |
| 83 | C.I V-Belt Pulley no. of Grooves -3, OD- 225mm, Thick.- 75mm, BORe- 115mm Supply Basis |
| 84 | C.I V-Belt Pulley no. of Grooves -3, OD- 225mm, Thick.- 75mm, BORe- 115mm Conversion Basis |
| 85 | CI beam as per drg. For Boiler conversion Basis |
| 86 | CI beam as per drg. For Boiler Supply basis |
| 87 | CenterPin EN-24 with CS Casting Complete for Mill Head Stock |
| 88 | Lever Pin EN-24 with CS Axle Complete of Mill Head Stock |
| 89 | CI Hanger for Bagasse Chute Approx 5mtr. |
